Added PWR and JTAG signals, added generated interface file.
This commit is contained in:
parent
35b1d52945
commit
06b0b6d731
GPG Key ID:
17F01E106F9F5E0A
|
|
@ -44,6 +44,8 @@ add_executable(${MCUX_SDK_PROJECT_NAME}
|
|||
"${ProjDirPath}/source/freertos_hello.c"
|
||||
"${ProjDirPath}/source/usb_application.c"
|
||||
"${ProjDirPath}/source/usb_application.h"
|
||||
"${ProjDirPath}/source/usb_device_interface_0_cic_vcom.c"
|
||||
"${ProjDirPath}/source/usb_device_interface_0_cic_vcom.h"
|
||||
"${ProjDirPath}/source/generated/usb_device_composite.c"
|
||||
"${ProjDirPath}/source/generated/usb_device_composite.h"
|
||||
"${ProjDirPath}/source/generated/usb_device_descriptor.c"
|
||||
|
|
|
|||
|
|
@ -40,6 +40,70 @@ BOARD_InitPins:
|
|||
- {pin_num: K14, peripheral: LPUART1, signal: TX, pin_signal: GPIO_AD_B0_12, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
|
||||
pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
|
||||
- {pin_num: G13, peripheral: GPIO1, signal: 'gpio_io, 10', pin_signal: GPIO_AD_B0_10, direction: OUTPUT, gpio_init_state: 'true'}
|
||||
- {pin_num: E14, peripheral: JTAG, signal: TMS, pin_signal: GPIO_AD_B0_06}
|
||||
- {pin_num: F12, peripheral: JTAG, signal: TCK, pin_signal: GPIO_AD_B0_07}
|
||||
- {pin_num: N1, peripheral: SUPPLY, signal: 'DCDC_GND, 0', pin_signal: DCDC_GND0}
|
||||
- {pin_num: N2, peripheral: SUPPLY, signal: 'DCDC_GND, 1', pin_signal: DCDC_GND1}
|
||||
- {pin_num: L1, peripheral: SUPPLY, signal: 'DCDC_IN, 0', pin_signal: DCDC_IN0}
|
||||
- {pin_num: L2, peripheral: SUPPLY, signal: 'DCDC_IN, 1', pin_signal: DCDC_IN1}
|
||||
- {pin_num: K4, peripheral: SUPPLY, signal: dcdc_in_q, pin_signal: DCDC_IN_Q}
|
||||
- {pin_num: M1, peripheral: SUPPLY, signal: 'DCDC_LP, 0', pin_signal: DCDC_LP0}
|
||||
- {pin_num: M2, peripheral: SUPPLY, signal: 'DCDC_LP, 1', pin_signal: DCDC_LP1}
|
||||
- {pin_num: K3, peripheral: SUPPLY, signal: dcdc_pswitch, pin_signal: DCDC_PSWITCH}
|
||||
- {pin_num: J5, peripheral: SUPPLY, signal: dcdc_sense, pin_signal: DCDC_SENSE}
|
||||
- {pin_num: N10, peripheral: SUPPLY, signal: gpanaio, pin_signal: GPANAIO}
|
||||
- {pin_num: K9, peripheral: SUPPLY, signal: ngnd_kel0, pin_signal: NGND_KEL0}
|
||||
- {pin_num: F5, peripheral: SUPPLY, signal: 'NVCC_EMC, 0', pin_signal: NVCC_EMC0}
|
||||
- {pin_num: E6, peripheral: SUPPLY, signal: 'NVCC_EMC, 1', pin_signal: NVCC_EMC1}
|
||||
- {pin_num: E9, peripheral: SUPPLY, signal: 'NVCC_GPIO, 0', pin_signal: NVCC_GPIO0}
|
||||
- {pin_num: F10, peripheral: SUPPLY, signal: 'NVCC_GPIO, 1', pin_signal: NVCC_GPIO1}
|
||||
- {pin_num: J10, peripheral: SUPPLY, signal: 'NVCC_GPIO, 2', pin_signal: NVCC_GPIO2}
|
||||
- {pin_num: P10, peripheral: SUPPLY, signal: nvcc_pll, pin_signal: NVCC_PLL}
|
||||
- {pin_num: J6, peripheral: SUPPLY, signal: nvcc_sd0, pin_signal: NVCC_SD0}
|
||||
- {pin_num: K5, peripheral: SUPPLY, signal: nvcc_sd1, pin_signal: NVCC_SD1}
|
||||
- {pin_num: K6, peripheral: SUPPLY, signal: test_mode, pin_signal: TEST_MODE}
|
||||
- {pin_num: N12, peripheral: SUPPLY, signal: usb_otg1_chd_b, pin_signal: USB_OTG1_CHD_B}
|
||||
- {pin_num: M8, peripheral: SUPPLY, signal: usb_otg1_dn, pin_signal: USB_OTG1_DN}
|
||||
- {pin_num: L8, peripheral: SUPPLY, signal: usb_otg1_dp, pin_signal: USB_OTG1_DP}
|
||||
- {pin_num: N6, peripheral: SUPPLY, signal: usb_otg1_vbus, pin_signal: USB_OTG1_VBUS}
|
||||
- {pin_num: N7, peripheral: SUPPLY, signal: usb_otg2_dn, pin_signal: USB_OTG2_DN}
|
||||
- {pin_num: P7, peripheral: SUPPLY, signal: usb_otg2_dp, pin_signal: USB_OTG2_DP}
|
||||
- {pin_num: P6, peripheral: SUPPLY, signal: usb_otg2_vbus, pin_signal: USB_OTG2_VBUS}
|
||||
- {pin_num: P8, peripheral: SUPPLY, signal: VDD_HIGH_CAP, pin_signal: VDD_HIGH_CAP}
|
||||
- {pin_num: P12, peripheral: SUPPLY, signal: VDD_HIGH_IN, pin_signal: VDD_HIGH_IN}
|
||||
- {pin_num: M10, peripheral: SUPPLY, signal: VDD_SNVS_CAP, pin_signal: VDD_SNVS_CAP}
|
||||
- {pin_num: M9, peripheral: SUPPLY, signal: VDD_SNVS_IN, pin_signal: VDD_SNVS_IN}
|
||||
- {pin_num: F6, peripheral: SUPPLY, signal: 'VDD_SOC_IN, 0', pin_signal: VDD_SOC_IN0}
|
||||
- {pin_num: G6, peripheral: SUPPLY, signal: 'VDD_SOC_IN, 1', pin_signal: VDD_SOC_IN1}
|
||||
- {pin_num: H6, peripheral: SUPPLY, signal: 'VDD_SOC_IN, 2', pin_signal: VDD_SOC_IN2}
|
||||
- {pin_num: F7, peripheral: SUPPLY, signal: 'VDD_SOC_IN, 3', pin_signal: VDD_SOC_IN3}
|
||||
- {pin_num: F8, peripheral: SUPPLY, signal: 'VDD_SOC_IN, 4', pin_signal: VDD_SOC_IN4}
|
||||
- {pin_num: F9, peripheral: SUPPLY, signal: 'VDD_SOC_IN, 5', pin_signal: VDD_SOC_IN5}
|
||||
- {pin_num: G9, peripheral: SUPPLY, signal: 'VDD_SOC_IN, 6', pin_signal: VDD_SOC_IN6}
|
||||
- {pin_num: H9, peripheral: SUPPLY, signal: 'VDD_SOC_IN, 7', pin_signal: VDD_SOC_IN7}
|
||||
- {pin_num: J9, peripheral: SUPPLY, signal: 'VDD_SOC_IN, 8', pin_signal: VDD_SOC_IN8}
|
||||
- {pin_num: K8, peripheral: SUPPLY, signal: VDD_USB_CAP, pin_signal: VDD_USB_CAP}
|
||||
- {pin_num: N14, peripheral: SUPPLY, signal: VDDA_ADC_3P3, pin_signal: VDDA_ADC_3P3}
|
||||
- {pin_num: A1, peripheral: SUPPLY, signal: 'VSS, 0', pin_signal: VSS0}
|
||||
- {pin_num: P1, peripheral: SUPPLY, signal: 'VSS, 1', pin_signal: VSS1}
|
||||
- {pin_num: E2, peripheral: SUPPLY, signal: 'VSS, 2', pin_signal: VSS2}
|
||||
- {pin_num: K2, peripheral: SUPPLY, signal: 'VSS, 3', pin_signal: VSS3}
|
||||
- {pin_num: B5, peripheral: SUPPLY, signal: 'VSS, 4', pin_signal: VSS4}
|
||||
- {pin_num: N5, peripheral: SUPPLY, signal: 'VSS, 5', pin_signal: VSS5}
|
||||
- {pin_num: G7, peripheral: SUPPLY, signal: 'VSS, 6', pin_signal: VSS6}
|
||||
- {pin_num: H7, peripheral: SUPPLY, signal: 'VSS, 7', pin_signal: VSS7}
|
||||
- {pin_num: J7, peripheral: SUPPLY, signal: 'VSS, 8', pin_signal: VSS8}
|
||||
- {pin_num: G8, peripheral: SUPPLY, signal: 'VSS, 9', pin_signal: VSS9}
|
||||
- {pin_num: H8, peripheral: SUPPLY, signal: 'VSS, 10', pin_signal: VSS10}
|
||||
- {pin_num: J8, peripheral: SUPPLY, signal: 'VSS, 11', pin_signal: VSS11}
|
||||
- {pin_num: N8, peripheral: SUPPLY, signal: 'VSS, 12', pin_signal: VSS12}
|
||||
- {pin_num: L9, peripheral: SUPPLY, signal: 'VSS, 13', pin_signal: VSS13}
|
||||
- {pin_num: B10, peripheral: SUPPLY, signal: 'VSS, 14', pin_signal: VSS14}
|
||||
- {pin_num: E13, peripheral: SUPPLY, signal: 'VSS, 15', pin_signal: VSS15}
|
||||
- {pin_num: K13, peripheral: SUPPLY, signal: 'VSS, 16', pin_signal: VSS16}
|
||||
- {pin_num: A14, peripheral: SUPPLY, signal: 'VSS, 17', pin_signal: VSS17}
|
||||
- {pin_num: P14, peripheral: SUPPLY, signal: 'VSS, 18', pin_signal: VSS18}
|
||||
- {pin_num: H10, peripheral: USB1, signal: usb_otg1_id, pin_signal: GPIO_AD_B0_01}
|
||||
* BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
|
||||
*/
|
||||
|
||||
|
|
@ -61,6 +125,9 @@ void BOARD_InitPins(void) {
|
|||
/* Initialize GPIO functionality on GPIO_AD_B0_10 (pin G13) */
|
||||
GPIO_PinInit(GPIO1, 10U, &INT1_COMBO_config);
|
||||
|
||||
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B0_01_USB_OTG1_ID, 0U);
|
||||
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B0_06_JTAG_TMS, 0U);
|
||||
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B0_07_JTAG_TCK, 0U);
|
||||
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B0_10_GPIO1_IO10, 0U);
|
||||
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B0_12_LPUART1_TX, 0U);
|
||||
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B0_13_LPUART1_RX, 0U);
|
||||
|
|
|
|||
|
|
@ -17,6 +17,7 @@ board: IMXRT1050-EVKB
|
|||
|
||||
#include "fsl_common.h"
|
||||
#include "fsl_iomuxc.h"
|
||||
#include "fsl_gpio.h"
|
||||
#include "pin_mux.h"
|
||||
|
||||
/* FUNCTION ************************************************************************************************************
|
||||
|
|
@ -38,6 +39,7 @@ BOARD_InitPins:
|
|||
pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
|
||||
- {pin_num: K14, peripheral: LPUART1, signal: TX, pin_signal: GPIO_AD_B0_12, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
|
||||
pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
|
||||
- {pin_num: G13, peripheral: GPIO1, signal: 'gpio_io, 10', pin_signal: GPIO_AD_B0_10, direction: OUTPUT, gpio_init_state: 'true'}
|
||||
* BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
|
||||
*/
|
||||
|
||||
|
|
@ -50,6 +52,16 @@ BOARD_InitPins:
|
|||
void BOARD_InitPins(void) {
|
||||
CLOCK_EnableClock(kCLOCK_Iomuxc);
|
||||
|
||||
/* GPIO configuration of INT1_COMBO on GPIO_AD_B0_10 (pin G13) */
|
||||
gpio_pin_config_t INT1_COMBO_config = {
|
||||
.direction = kGPIO_DigitalOutput,
|
||||
.outputLogic = 1U,
|
||||
.interruptMode = kGPIO_NoIntmode
|
||||
};
|
||||
/* Initialize GPIO functionality on GPIO_AD_B0_10 (pin G13) */
|
||||
GPIO_PinInit(GPIO1, 10U, &INT1_COMBO_config);
|
||||
|
||||
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B0_10_GPIO1_IO10, 0U);
|
||||
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B0_12_LPUART1_TX, 0U);
|
||||
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B0_13_LPUART1_RX, 0U);
|
||||
IOMUXC_SetPinConfig(IOMUXC_GPIO_AD_B0_12_LPUART1_TX, 0x10B0U);
|
||||
|
|
|
|||
|
|
@ -61,6 +61,36 @@ void BOARD_InitBootPins(void);
|
|||
#define BOARD_INITPINS_INT1_COMBO_PIN 10U /*!< PORT pin number */
|
||||
#define BOARD_INITPINS_INT1_COMBO_PIN_MASK (1U << 10U) /*!< PORT pin mask */
|
||||
|
||||
/* NVCC_SD0 (coord J6), NVCC_SD */
|
||||
/* Routed pin properties */
|
||||
#define BOARD_INITPINS_NVCC_SD_PERIPHERAL SUPPLY /*!< Peripheral name */
|
||||
#define BOARD_INITPINS_NVCC_SD_SIGNAL nvcc_sd0 /*!< Signal name */
|
||||
|
||||
/* NVCC_SD1 (coord K5), FLASH_VCC */
|
||||
/* Routed pin properties */
|
||||
#define BOARD_INITPINS_FLASH_VCC_PERIPHERAL SUPPLY /*!< Peripheral name */
|
||||
#define BOARD_INITPINS_FLASH_VCC_SIGNAL nvcc_sd1 /*!< Signal name */
|
||||
|
||||
/* USB_OTG1_DN (coord M8), OTG1_DN */
|
||||
/* Routed pin properties */
|
||||
#define BOARD_INITPINS_OTG1_DN_PERIPHERAL SUPPLY /*!< Peripheral name */
|
||||
#define BOARD_INITPINS_OTG1_DN_SIGNAL usb_otg1_dn /*!< Signal name */
|
||||
|
||||
/* USB_OTG1_DP (coord L8), OTG1_DP */
|
||||
/* Routed pin properties */
|
||||
#define BOARD_INITPINS_OTG1_DP_PERIPHERAL SUPPLY /*!< Peripheral name */
|
||||
#define BOARD_INITPINS_OTG1_DP_SIGNAL usb_otg1_dp /*!< Signal name */
|
||||
|
||||
/* USB_OTG2_DN (coord N7), OTG2_DN */
|
||||
/* Routed pin properties */
|
||||
#define BOARD_INITPINS_OTG2_DN_PERIPHERAL SUPPLY /*!< Peripheral name */
|
||||
#define BOARD_INITPINS_OTG2_DN_SIGNAL usb_otg2_dn /*!< Signal name */
|
||||
|
||||
/* USB_OTG2_DP (coord P7), OTG2_DP */
|
||||
/* Routed pin properties */
|
||||
#define BOARD_INITPINS_OTG2_DP_PERIPHERAL SUPPLY /*!< Peripheral name */
|
||||
#define BOARD_INITPINS_OTG2_DP_SIGNAL usb_otg2_dp /*!< Signal name */
|
||||
|
||||
|
||||
/*!
|
||||
* @brief Configures pin routing and optionally pin electrical features.
|
||||
|
|
|
|||
|
|
@ -47,6 +47,20 @@ void BOARD_InitBootPins(void);
|
|||
#define BOARD_INITPINS_UART1_TXD_PERIPHERAL LPUART1 /*!< Peripheral name */
|
||||
#define BOARD_INITPINS_UART1_TXD_SIGNAL TX /*!< Signal name */
|
||||
|
||||
/* GPIO_AD_B0_10 (coord G13), JTAG_TDO/J21[13]/INT1_COMBO/ENET_INT/J22[6]/U32[11] */
|
||||
/* Routed pin properties */
|
||||
#define BOARD_INITPINS_INT1_COMBO_PERIPHERAL GPIO1 /*!< Peripheral name */
|
||||
#define BOARD_INITPINS_INT1_COMBO_SIGNAL gpio_io /*!< Signal name */
|
||||
#define BOARD_INITPINS_INT1_COMBO_CHANNEL 10U /*!< Signal channel */
|
||||
|
||||
/* Symbols to be used with GPIO driver */
|
||||
#define BOARD_INITPINS_INT1_COMBO_GPIO GPIO1 /*!< GPIO peripheral base pointer */
|
||||
#define BOARD_INITPINS_INT1_COMBO_GPIO_PIN 10U /*!< GPIO pin number */
|
||||
#define BOARD_INITPINS_INT1_COMBO_GPIO_PIN_MASK (1U << 10U) /*!< GPIO pin mask */
|
||||
#define BOARD_INITPINS_INT1_COMBO_PORT GPIO1 /*!< PORT peripheral base pointer */
|
||||
#define BOARD_INITPINS_INT1_COMBO_PIN 10U /*!< PORT pin number */
|
||||
#define BOARD_INITPINS_INT1_COMBO_PIN_MASK (1U << 10U) /*!< PORT pin mask */
|
||||
|
||||
|
||||
/*!
|
||||
* @brief Configures pin routing and optionally pin electrical features.
|
||||
|
|
|
|||
|
|
@ -39,6 +39,21 @@
|
|||
<data>true</data>
|
||||
</feature>
|
||||
</dependency>
|
||||
<dependency resourceType="Peripheral" resourceId="JTAG" description="Peripheral JTAG is not initialized" problem_level="1" source="Pins:BOARD_InitPins">
|
||||
<feature name="initialized" evaluation="equal">
|
||||
<data>true</data>
|
||||
</feature>
|
||||
</dependency>
|
||||
<dependency resourceType="Peripheral" resourceId="SUPPLY" description="Peripheral SUPPLY is not initialized" problem_level="1" source="Pins:BOARD_InitPins">
|
||||
<feature name="initialized" evaluation="equal">
|
||||
<data>true</data>
|
||||
</feature>
|
||||
</dependency>
|
||||
<dependency resourceType="Peripheral" resourceId="USB1" description="Peripheral USB1 is not initialized" problem_level="1" source="Pins:BOARD_InitPins">
|
||||
<feature name="initialized" evaluation="equal">
|
||||
<data>true</data>
|
||||
</feature>
|
||||
</dependency>
|
||||
<dependency resourceType="SWComponent" resourceId="platform.drivers.common" description="Pins initialization requires the COMMON Driver in the project." problem_level="2" source="Pins:BOARD_InitPins">
|
||||
<feature name="enabled" evaluation="equal" configuration="core0">
|
||||
<data>true</data>
|
||||
|
|
@ -88,6 +103,70 @@
|
|||
<pin_feature name="gpio_init_state" value="true"/>
|
||||
</pin_features>
|
||||
</pin>
|
||||
<pin peripheral="JTAG" signal="TMS" pin_num="E14" pin_signal="GPIO_AD_B0_06"/>
|
||||
<pin peripheral="JTAG" signal="TCK" pin_num="F12" pin_signal="GPIO_AD_B0_07"/>
|
||||
<pin peripheral="SUPPLY" signal="DCDC_GND, 0" pin_num="N1" pin_signal="DCDC_GND0"/>
|
||||
<pin peripheral="SUPPLY" signal="DCDC_GND, 1" pin_num="N2" pin_signal="DCDC_GND1"/>
|
||||
<pin peripheral="SUPPLY" signal="DCDC_IN, 0" pin_num="L1" pin_signal="DCDC_IN0"/>
|
||||
<pin peripheral="SUPPLY" signal="DCDC_IN, 1" pin_num="L2" pin_signal="DCDC_IN1"/>
|
||||
<pin peripheral="SUPPLY" signal="dcdc_in_q" pin_num="K4" pin_signal="DCDC_IN_Q"/>
|
||||
<pin peripheral="SUPPLY" signal="DCDC_LP, 0" pin_num="M1" pin_signal="DCDC_LP0"/>
|
||||
<pin peripheral="SUPPLY" signal="DCDC_LP, 1" pin_num="M2" pin_signal="DCDC_LP1"/>
|
||||
<pin peripheral="SUPPLY" signal="dcdc_pswitch" pin_num="K3" pin_signal="DCDC_PSWITCH"/>
|
||||
<pin peripheral="SUPPLY" signal="dcdc_sense" pin_num="J5" pin_signal="DCDC_SENSE"/>
|
||||
<pin peripheral="SUPPLY" signal="gpanaio" pin_num="N10" pin_signal="GPANAIO"/>
|
||||
<pin peripheral="SUPPLY" signal="ngnd_kel0" pin_num="K9" pin_signal="NGND_KEL0"/>
|
||||
<pin peripheral="SUPPLY" signal="NVCC_EMC, 0" pin_num="F5" pin_signal="NVCC_EMC0"/>
|
||||
<pin peripheral="SUPPLY" signal="NVCC_EMC, 1" pin_num="E6" pin_signal="NVCC_EMC1"/>
|
||||
<pin peripheral="SUPPLY" signal="NVCC_GPIO, 0" pin_num="E9" pin_signal="NVCC_GPIO0"/>
|
||||
<pin peripheral="SUPPLY" signal="NVCC_GPIO, 1" pin_num="F10" pin_signal="NVCC_GPIO1"/>
|
||||
<pin peripheral="SUPPLY" signal="NVCC_GPIO, 2" pin_num="J10" pin_signal="NVCC_GPIO2"/>
|
||||
<pin peripheral="SUPPLY" signal="nvcc_pll" pin_num="P10" pin_signal="NVCC_PLL"/>
|
||||
<pin peripheral="SUPPLY" signal="nvcc_sd0" pin_num="J6" pin_signal="NVCC_SD0"/>
|
||||
<pin peripheral="SUPPLY" signal="nvcc_sd1" pin_num="K5" pin_signal="NVCC_SD1"/>
|
||||
<pin peripheral="SUPPLY" signal="test_mode" pin_num="K6" pin_signal="TEST_MODE"/>
|
||||
<pin peripheral="SUPPLY" signal="usb_otg1_chd_b" pin_num="N12" pin_signal="USB_OTG1_CHD_B"/>
|
||||
<pin peripheral="SUPPLY" signal="usb_otg1_dn" pin_num="M8" pin_signal="USB_OTG1_DN"/>
|
||||
<pin peripheral="SUPPLY" signal="usb_otg1_dp" pin_num="L8" pin_signal="USB_OTG1_DP"/>
|
||||
<pin peripheral="SUPPLY" signal="usb_otg1_vbus" pin_num="N6" pin_signal="USB_OTG1_VBUS"/>
|
||||
<pin peripheral="SUPPLY" signal="usb_otg2_dn" pin_num="N7" pin_signal="USB_OTG2_DN"/>
|
||||
<pin peripheral="SUPPLY" signal="usb_otg2_dp" pin_num="P7" pin_signal="USB_OTG2_DP"/>
|
||||
<pin peripheral="SUPPLY" signal="usb_otg2_vbus" pin_num="P6" pin_signal="USB_OTG2_VBUS"/>
|
||||
<pin peripheral="SUPPLY" signal="VDD_HIGH_CAP" pin_num="P8" pin_signal="VDD_HIGH_CAP"/>
|
||||
<pin peripheral="SUPPLY" signal="VDD_HIGH_IN" pin_num="P12" pin_signal="VDD_HIGH_IN"/>
|
||||
<pin peripheral="SUPPLY" signal="VDD_SNVS_CAP" pin_num="M10" pin_signal="VDD_SNVS_CAP"/>
|
||||
<pin peripheral="SUPPLY" signal="VDD_SNVS_IN" pin_num="M9" pin_signal="VDD_SNVS_IN"/>
|
||||
<pin peripheral="SUPPLY" signal="VDD_SOC_IN, 0" pin_num="F6" pin_signal="VDD_SOC_IN0"/>
|
||||
<pin peripheral="SUPPLY" signal="VDD_SOC_IN, 1" pin_num="G6" pin_signal="VDD_SOC_IN1"/>
|
||||
<pin peripheral="SUPPLY" signal="VDD_SOC_IN, 2" pin_num="H6" pin_signal="VDD_SOC_IN2"/>
|
||||
<pin peripheral="SUPPLY" signal="VDD_SOC_IN, 3" pin_num="F7" pin_signal="VDD_SOC_IN3"/>
|
||||
<pin peripheral="SUPPLY" signal="VDD_SOC_IN, 4" pin_num="F8" pin_signal="VDD_SOC_IN4"/>
|
||||
<pin peripheral="SUPPLY" signal="VDD_SOC_IN, 5" pin_num="F9" pin_signal="VDD_SOC_IN5"/>
|
||||
<pin peripheral="SUPPLY" signal="VDD_SOC_IN, 6" pin_num="G9" pin_signal="VDD_SOC_IN6"/>
|
||||
<pin peripheral="SUPPLY" signal="VDD_SOC_IN, 7" pin_num="H9" pin_signal="VDD_SOC_IN7"/>
|
||||
<pin peripheral="SUPPLY" signal="VDD_SOC_IN, 8" pin_num="J9" pin_signal="VDD_SOC_IN8"/>
|
||||
<pin peripheral="SUPPLY" signal="VDD_USB_CAP" pin_num="K8" pin_signal="VDD_USB_CAP"/>
|
||||
<pin peripheral="SUPPLY" signal="VDDA_ADC_3P3" pin_num="N14" pin_signal="VDDA_ADC_3P3"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 0" pin_num="A1" pin_signal="VSS0"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 1" pin_num="P1" pin_signal="VSS1"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 2" pin_num="E2" pin_signal="VSS2"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 3" pin_num="K2" pin_signal="VSS3"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 4" pin_num="B5" pin_signal="VSS4"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 5" pin_num="N5" pin_signal="VSS5"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 6" pin_num="G7" pin_signal="VSS6"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 7" pin_num="H7" pin_signal="VSS7"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 8" pin_num="J7" pin_signal="VSS8"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 9" pin_num="G8" pin_signal="VSS9"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 10" pin_num="H8" pin_signal="VSS10"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 11" pin_num="J8" pin_signal="VSS11"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 12" pin_num="N8" pin_signal="VSS12"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 13" pin_num="L9" pin_signal="VSS13"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 14" pin_num="B10" pin_signal="VSS14"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 15" pin_num="E13" pin_signal="VSS15"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 16" pin_num="K13" pin_signal="VSS16"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 17" pin_num="A14" pin_signal="VSS17"/>
|
||||
<pin peripheral="SUPPLY" signal="VSS, 18" pin_num="P14" pin_signal="VSS18"/>
|
||||
<pin peripheral="USB1" signal="usb_otg1_id" pin_num="H10" pin_signal="GPIO_AD_B0_01"/>
|
||||
</pins>
|
||||
</function>
|
||||
</functions_list>
|
||||
|
|
|
|||
Loading…
Reference in New Issue