sunxi: dts: arm: update devicetree files from Linux-v6.6-rc6

Sync the devicetree files from the official Linux kernel tree, v6.6-rc6.
This is covering Allwinner SoCs with 32-bit ARM cores, minus the T113s
board and related .dtsi files, which come separately.

Only small changes: Bluetooth got enabled on the C.H.I.P., and a clock
got renamed. More interesting is the addition of a board, for which
U-Boot enablement patches are pending.

As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>

arch/arm/dts/axp209.dtsi

@@ -48,6 +48,13 @@
  * http://dl.linux-sunxi.org/AXP/AXP209%20Datasheet%20v1.0_cn.pdf
  */
 
+/ {
+	pmic-temp {
+		compatible = "iio-hwmon";
+		io-channels = <&axp_adc 4>; /* Internal temperature */
+	};
+};
+
 &axp209 {
 	compatible = "x-powers,axp209";
 	interrupt-controller;

arch/arm/dts/sun5i-r8-chip.dts

@@ -255,6 +255,12 @@
 	pinctrl-0 = <&uart3_pg_pins>,
 		    <&uart3_cts_rts_pg_pins>;
 	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723bs-bt";
+		device-wake-gpios = <&axp_gpio 3 GPIO_ACTIVE_HIGH>;
+		host-wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+	};
 };
 
 &usb_otg {

arch/arm/dts/sun5i.dtsi

@@ -286,7 +286,7 @@
 			clock-names = "ahb",
 				      "tcon-ch0",
 				      "tcon-ch1";
-			clock-output-names = "tcon-pixel-clock";
+			clock-output-names = "tcon-data-clock";
 			#clock-cells = <0>;
 			status = "disabled";
 
@@ -517,6 +517,15 @@
 				bias-pull-up;
 			};
 
+			/omit-if-no-ref/
+			mmc2_4bit_pe_pins: mmc2-4bit-pe-pins {
+				pins = "PE4", "PE5", "PE6", "PE7",
+				       "PE8", "PE9";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
 			mmc2_8bit_pins: mmc2-8bit-pins {
 				pins = "PC6", "PC7", "PC8", "PC9",
 				       "PC10", "PC11", "PC12", "PC13",

arch/arm/dts/sun7i-a20-icnova-a20-adb4006.dts

@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2023 In-Circuit GmbH
+
+/dts-v1/;
+
+#include "sun7i-a20-icnova-a20.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "In-Circuit ICnova A20 ADB4006";
+	compatible = "incircuit,icnova-a20-adb4006", "incircuit,icnova-a20",
+		     "allwinner,sun7i-a20";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_YELLOW>;
+			gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* PH21 */
+			default-state = "on";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* PH20 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&ahci {
+	target-supply = <&reg_ahci_5v>;
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&reg_ahci_5v {
+	status = "okay";
+};
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+	usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};

arch/arm/dts/sun7i-a20-icnova-a20.dtsi

@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2023 In-Circuit GmbH
+
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_mii_pins>;
+	phy-handle = <&phy1>;
+	phy-mode = "mii";
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&gmac_mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};

arch/arm/dts/sun8i-a23-a33.dtsi

@@ -190,7 +190,7 @@
 			clock-names = "ahb",
 				      "tcon-ch0",
 				      "lvds-alt";
-			clock-output-names = "tcon-pixel-clock";
+			clock-output-names = "tcon-data-clock";
 			#clock-cells = <0>;
 			resets = <&ccu RST_BUS_LCD>,
 				 <&ccu RST_BUS_LVDS>;

arch/arm/dts/sun8i-a83t.dtsi

@@ -456,7 +456,7 @@
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
 			clock-names = "ahb", "tcon-ch0";
-			clock-output-names = "tcon-pixel-clock";
+			clock-output-names = "tcon-data-clock";
 			#clock-cells = <0>;
 			resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>;
 			reset-names = "lcd", "lvds";

arch/arm/dts/sun8i-v3s.dtsi

@@ -191,7 +191,7 @@
 				 <&ccu CLK_TCON0>;
 			clock-names = "ahb",
 				      "tcon-ch0";
-			clock-output-names = "tcon-pixel-clock";
+			clock-output-names = "tcon-data-clock";
 			#clock-cells = <0>;
 			resets = <&ccu RST_BUS_TCON0>;
 			reset-names = "lcd";