Similar change was done by commit b4c2c151b1 ("Kconfig: Remove all
default n/no options") and again sync is required.
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com> # tegra
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@kernel-space.org>
On Rockchip SoCs the first boot stages are written on NAND
with help of manufacturer software that uses a different format
then the MTD framework. Skip the automatic BBT scan with the
NAND_SKIP_BBTSCAN option to be able to pass the driver probe
function and to let the original data unchanged.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the iproc Broadcom NAND controller,
used in Northstar SoCs for example. Based on the Linux
driver.
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/all/20230308214231.378013-1-linus.walleij@linaro.org/
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add a new Kconfig option CONFIG_MVEBU_SPL_BOOT_DEVICE_NAND which instruct
make to generate kwbimage with NAND header. This image is used for booting
from NAND flash (either SPI or parallel).
Support is very simple, SPL after finishes DDR training returns back to the
BootROM (via CONFIG_SPL_BOOTROM_SUPPORT option) and BootROM then loads and
executes U-Boot proper.
To generate correct kwbimage NAND header, it is required to set following
Kconfig options:
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_MVEBU_SPL_NAND_BADBLK_LOCATION
They are used only by make / mkimage when generating final kwbimage.
CONFIG_MVEBU_SPL_NAND_BADBLK_LOCATION is a new mvebu specific Kconfig
option which is set into kwbimage NAND_BADBLK_LOCATION header field.
Signed-off-by: Pali Rohár <pali@kernel.org>
- rawnand: omap_gpmc: driver model support
-----BEGIN PGP SIGNATURE-----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=Agfn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20230108' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash into next
Pull request for u-boot-nand-20230108
- rawnand: omap_gpmc: driver model support
The symbol is required for NAND support in SPL when using
OMAP_GPMC driver.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-7-rogerq@kernel.org
Enables SPL NAND support for ARCH_K3 by enabling
SPL_NAND_INIT and SPL_SYS_NAND_SELF_INIT.
Legacy OMAP2plus platforms still rely on SPL_NAND_AM33XX_BCH
instead.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-6-rogerq@kernel.org
Adds driver model support.
We need to be able to self initialize the NAND controller/chip
at probe and so enable CONFIG_SYS_NAND_SELF_INIT.
Doing so requires nand_register() API which is provided by nand.c
and needs to be enabled during SPL build via CONFIG_SPL_NAND_INIT.
But nand.c also provides nand_init() so we need to get rid of nand_init()
in omap_gpmc driver if CONFIG_SPL_NAND_INIT is set.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221220102203.52398-5-rogerq@kernel.org
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmO2mnEcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBAOB/4y7e9y0jdKSWDwMdZj
enXK/U/GREFyuiSdadil0aJl9WfayjwZkh7uHSTj4pi9ApNivfoqsL7WZYpJxhRD
WlpNhs3TZ70i8CgKUosdzcpquAQZUZhg6iV5DCObrK6yNJRGOXLIwMOd+vw/Xz6/
YTGqzivEDMBuH/9HLuC0m+26PEpff8nenNEjC2k8ssG26ojLz7oCQh2HoHcSgNRc
HkEYlFJ/Le8kM8Ak2F3ebmsfgMTnFrRVwV1BsZa5vO0BrMYgJCORsl7Cnfcw6/2N
LEHG7kwlSorJeETn/gkLiZ+NyqzU+oFH0jGRZ5Ciqg1qcCO3k9yBMgWQzd7nTL6C
5oZA
=Ocdd
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.04 cycle:
This feature set includes the new DM-based NAND flash driver (old non-DM
driver is still kept for backwards compatibility), and the move to DM
NAND flash driver for sam9x60ek board. Feature set also includes
devicetree alignment for sama7g5 with Linux, devicetree alignment on USB
with Linux for all boards (sama5, sam9x60), chip id for sama7g5, minor
configs and tweaks.
Add the CONFIG_SYS_NAND_SELF_INIT to the Kconfig to follow the changes from
mainline.
Signed-off-by: Lokanathan, Raaj <raaj.lokanathan@intel.com>
Signed-off-by: Jit Loon Lim <jit.loon.lim@intel.com>
The GPMC module is present on some K2 and K3 SoCs.
Enable building GPMC NAND driver for K2/K3 platforms.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-By: Michael Trimarchi <michael@amarulasolutions.com>
Link: https://lore.kernel.org/all/20221011115012.6181-3-rogerq@kernel.org
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
This implementation is ported from the rework done by Boris Brezillon
in Linux. This porting is done based on linux-5.4-at91. The driver is
tested in sam9x60ek, sama5d3_xplained, sam9x75eb and sama7g54-ddr3-eb.
Changes done includes
- Adapt GPIO descriptor apis for U-Boot. Use gpio_request_by_name_nodev,
dm_gpio_get_value etc.
- Use U_BOOT_DRIVER instead of platform_driver.
- Replace struct platform_device with struct udevice
- Check the status of nfc exec operation by polling the status
register instead of interrupt based handling
- DMA operations not supported. Remove it
- Adapt DT parsing to U-Boot APIs
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_PAGE_2K
CONFIG_SYS_NAND_PAGE_4K
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_HW_ECC
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_HW_ECC_OOBFIRST
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_DBW_8
CONFIG_SYS_NAND_DBW_16
Note that all instances of the code check for CONFIG_SYS_NAND_DBW_16
being defined, and then "else" to CONFIG_SYS_NAND_DBW_8 whereas all of
the configs set CONFIG_SYS_NAND_DBW_8. So we introduce
CONFIG_SYS_NAND_DBW_16 as an option.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_MAX_NAND_DEVICE
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As CONFIG_ARCH_BCM6753 is replaced with CONFIG_BCM6855, update the
driver Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
As CONFIG_ARCH_BCM6858 is replaced with CONFIG_BCM6858, update the
driver Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
As CONFIG_ARCH_BCM68360 is replaced with CONFIG_BCM6856, update the
driver Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
As CONFIG_ARCH_BCM63158 is replaced with CONFIG_BCM63158, update the
Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
This patch adds NAND flash controller driver for MediaTek MT7621 SoC.
The NAND flash controller of MT7621 supports only SLC NAND flashes.
It supports 4~12 bits correction with maximum 4KB page size.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Tighten up symbol dependencies in a number of places. Ensure that a SPL
specific option has at least a direct dependency on SPL. In places
where it's clear that we depend on something more specific, use that
dependency instead. This means in a very small number of places we can
drop redundant dependencies.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This allows boards to specify NAND settings via standard DT properties.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In order to finish this conversion we need to add a symbols for
SPL_SYS_NAND_SELF_INIT and TPL_SYS_NAND_SELF_INIT as there are cases
there where we need to, or need to not, use that framework as things
stand.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
In order to do this conversion, expose this option to the user and
use "save" not "safe" in the text.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FSL_IFC
This is done via select statements to match previous logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a driver for Macronix raw NAND controller.
This patch referred from linux mxic_nand.c. The difference from the
linux version is described here.
1. In order to adapt to the uboot nand framework, add function
binding (cmdfunc, read_byte, read_buf, write_buf).
2. Added parsing command format to use hardware correctly.
3. Remove the incompatible functions of Uboot.
Signed-off-by: Zhengxun Li <zhengxunli@mxic.com.tw>
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
