Fix flash@0 partition node name with correct offset.
Fixes: 90f992e6a5 ("arm: dts: stm32: Add partitions in flash0 and nand
node for stm32mp15xx-dhcom/dhcor")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The patch fixed by this commit renders ST STM32MP15xx EV1 board and
all DHSOM SoM based boards unbootable from SPI NOR. Fix the damage
by updating -u-boot.dtsi to match the stm32mp15-pinctrl.dtsi update.
Fixes: 08002ffd08 ("ARM: dts: stm32mp: alignment with v6.3")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The DHCOM SoM has two options for supplying ETHRX clock to the DWMAC
block and PHY. Either (1) ETHCK_K generates 50 MHz clock on ETH_CLK
pad for the PHY and the same 50 MHz clock are fed back to ETHRX via
internal eth_clk_fb clock connection OR (2) ETH_CLK is not used at
all, MCO2 generates 50 MHz clock on MCO2 output pad for the PHY and
the same MCO2 clock are fed back into ETHRX via ETH_RX_CLK input pad
using external pad-to-pad connection.
Option (1) has two downsides. ETHCK_K is supplied directly from either
PLL3_Q or PLL4_P, hence the PLL output is limited to exactly 50 MHz and
since the same PLL output is also used to supply SDMMC blocks, the
performance of SD and eMMC access is affected. The second downside is
that using this option, the EMI of the SoM is higher.
Option (2) solves both of those problems, so implement it here. In this
case, the PLL4_P is no longer limited and can be operated faster, at
100 MHz, which improves SDMMC performance (read performance is improved
from ~41 MiB/s to ~57 MiB/s with dd if=/dev/mmcblk1 of=/dev/null bs=64M
count=1). The EMI interference also decreases.
Ported from Linux kernel commit
73ab99aad50cd ("ARM: dts: stm32: Switch DWMAC RMII clock to MCO2 on DHCOM")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Fix the frequencies listed in PLL configuration comments to match
the actual frequencies programmed into hardware. Furthermore, add
a comment which explains how those frequencies are calculated, so
it won't be necessary to look it up all over the datasheet and
make more mistakes in the calculation in the future.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Perform long overdue conversion of ad-hoc FMC2 EBI bus initialization
to upstream FMC2 EBI driver. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
PA13 and PA14 are used for USB power control and can't be used
to enforce fastboot or stm32prog mode by pressing a button.
Defining CONFIG_FASTBOOT/CONFIG_CMD_STM32PROG without this patch applied
results in fastboot/stm32prog always starting, because PA13/PA14 are always
low during boot. So drop the wrong trigger gpios definitions.
Signed-off-by: Johann Neuhauser <jneuhauser@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This patch configures U-Boot SPL for DHCOM SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
The DFU usage procedure is identical to STM32MP1 DHCOR SoM, see commit
3919aa1722 ("ARM: dts: stm32: Add DFU support for DHCOR recovery") ,
except for switching the SoM into DFU mode. By default, the DHCOM SoM
has no dedicated mechanism for setting BOOTn straps into UART/USB mode,
therefore to enter DFU mode, the SoC must fail to boot from boot media
which can be selected by the BOOTn strap override mechanism first and
then fall back to DFU mode.
In case of a SoM with pre-populated BOOTn strap override button, power
the system off, remove microSD card (if applicable), hold down the BOOTn
strap override button located between eMMC and SoM edge connector, power
on the SoM. The SoC will fail to boot from SD card and fall back into
DFU mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Synchronize DH DHCOM DTs with Linux commit 25960cafa06e ("Linux 5.15.12").
There is no functional change to the resulting DTs. The eeprom0 alias and
PHY reset GPIO are now reinstated in SoM u-boot dtsi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The uSD level translator on DHSOM and Avenger96 are optional, however it
is possible to auto-detect it. This is done by setting SD CMD line high,
and then testing whether signal level on CK line matches the signal level
on CKIN line. If so, the uSD level translator is present, otherwise it is
not populated.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The nWP GPIO hog was used to unlock the SPI NOR write protect when U-Boot
used to operate the SPI NOR in 1-1-1 mode. Now that the SPI NOR is operated
in 1-1-4 mode, the hog has adverse effects and causes transfer corruption,
since the hogged pin is also the IO2 pin. Remove the hogs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Device tree alignment with Linux kernel v5.11-rc2
- fix DCMI DMA features on stm32mp15 family
- Add alternate pinmux for FMC EBI bus
- Harmonize EHCI/OHCI DT nodes name on stm32mp15
- update sdmmc IP version for STM32MP15
- Add LP timer irqs on stm32mp151
- Add LP timer wakeup-source on stm32mp151
- enable HASH by default on stm32mp15
- enable CRC1 by default on stm32mp15
- enable CRYP by default on stm32mp15
- set bus-type in DCMI endpoint for stm32mp157c-ev1 board
- reorder spi4 within stm32mp15-pinctrl
- add STUSB1600 Type-C using I2C4 on stm32mp15xx-dkx
- fix mdma1 clients channel priority level on stm32mp151
- fix dmamux reg property on stm32mp151
- adjust USB OTG gadget fifo sizes in stm32mp151
- update stm32mp151 for remote proc synchronization support
- support child mfd cells for the stm32mp1 TAMP syscon
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The LAN8710i PHY currently uses 50 MHz clock direct from PLL4P.
To permit PLL4P to run at faster frequency, use MCO2 as a divider.
The PLL4P runs at 100 MHz, supplies MCO2 which divides it by 2 to
50MHz, and supplies the PHY with 50 MHz via pin PG2. The feedback
clock are fed back in via pin PA1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change-Id: Ia9bf7119785d49b633a3ae761c3dc4a30b92628a
The STM32MP1 DHCOM has two ethernet interfaces, the on-SoM DWMAC and KS8851.
Set eth1addr for the KS8851 to a MAC address of the DWMAC incremented by 1.
The MAC of the DWMAC is set from on-SoM EEPROM already, but the MAC address
of KS8851 was left uninitialized, so fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Since commit f13ff88b61 ("gpio: stm32: add ops set_dir_flags")
the gpio flags are supported by stm32 pinctrl driver.
The cd-gpios is correctly handle in U-Boot and the patch on the
device tree can be removed.
This reverts commit 3c2e2a1a79.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch allows to switch the CPU frequency to 800MHz on the
ST Microelectronics board (DK1/DK2 and EV1) or dh electronics SOM
using the STM32MP15x SOC and when it is supported by the HW
(for STM32MP15xD and STM32MP15xF).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The cd-gpios with (GPIO_ACTIVE_LOW | GPIO_PULL_UP) gpio is thus far
unsupported, reinstate the old cd-gpios behavior until this handling
is fully implemented. This permits the DHSOM to boot from SD again,
without this patch the card detect fails.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The SPI NOR nWP line is connected to GPIO PF7 on the SoM,
pull the GPIO line high by default to clear SPI NOR WP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add custom DDR DRAM settings for the DHCOR and DHCOM SoMs and put them
into use by the board file instead of the default ones. These new DRAM
settings are a better fit for the SoMs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The DHCOR board does exist in multiple variants with different DDR3
DRAM sizes. To cater for all of them, implement DDR3 code handling.
There are two GPIOs which code the DRAM size populated on the SoM,
read them out and use the value to pick the correct DDR3 config.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
The AV96 board does exist in multiple variants. To cater for all of
them, implement board code handling. There are two GPIOs which code
the type of the board, read them out and use the value to pick the
correct device tree from an fitImage.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Iddb330b9a66500495885457cbe17edc0eacaaf43
Add DT entries, Kconfig entries and board-specific entries to configure
FMC2 bus and make KS8851-16MLL on that bus accessible to U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This commit manages diversity for STM32M15x SOCs with:
- dedicated files to support all STM32MP15 SOCs family.
The differences between those SOCs are:
-STM32MP151 [1]: common file.
-STM32MP153 [2]: STM32MP151 + CANs + a second CortexA7-CPU.
-STM32MP157 [3]: STM32MP153 + DSI + GPU.
- new files to manage security diversity on STM32MP15x SOCs.
On STM32MP15xY, "Y" gives information:
-Y = A means no cryp IP and no secure boot.
-Y = C means cryp IP + secure boot.
- stm32mp157 pinctrl files to better manage package diversity.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Fix the following DT dtc warnings for stm32mp1 boards:
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@0:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@1:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@2:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@3:
node has a unit name, but no reg property
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
LTDC modifies the clock frequency to adapt it to the display. Such
frequency change is not detected by the FDCAN driver that instead
cache the value at probe and pretend to use it later.
Keep the LTDC alone on PLL4_Q by moving the FDCAN to PLL4_R.
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
