f626382d08
When using a list of writeable variables, the initial values come from the built-in default environment since commit5ab8105836("env: Complete generic support for writable list"). Remove unnecessary misuse of CONFIG_ENV_IS_NOWHERE as default environment. Based on the fix done by commitb16fd7f75f("imx6q: acc: Remove misuse of env is nowhere driver"). Signed-off-by: Eduard Strehlau <eduard@lionizers.com> Signed-off-by: Fabio Estevam <festevam@denx.de>
114 lines
2.4 KiB
C
114 lines
2.4 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
// Copyright (C) 2021 Fabio Estevam <festevam@denx.de>
|
|
|
|
#include <init.h>
|
|
#include <net.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <asm/arch/mx7-pins.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/mach-imx/hab.h>
|
|
#include <asm/mach-imx/iomux-v3.h>
|
|
#include <asm/io.h>
|
|
#include <common.h>
|
|
#include <env.h>
|
|
#include <env_internal.h>
|
|
#include <asm/arch/crm_regs.h>
|
|
#include <asm/setup.h>
|
|
#include <asm/bootm.h>
|
|
#include <mmc.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUS_PU100KOHM | \
|
|
PAD_CTL_HYS)
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = PHYS_SDRAM_SIZE;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static iomux_v3_cfg_t const wdog_pads[] = {
|
|
MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const uart1_pads[] = {
|
|
MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
};
|
|
|
|
static void setup_iomux_uart(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
|
|
};
|
|
|
|
static int setup_fec(void)
|
|
{
|
|
struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs =
|
|
(struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
|
|
int ret;
|
|
|
|
/* Use 125M anatop REF_CLK1 for ENET1, clear gpr1[13], gpr1[17]*/
|
|
clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
|
|
(IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_MASK |
|
|
IOMUXC_GPR_GPR1_GPR_ENET1_CLK_DIR_MASK), 0);
|
|
|
|
ret = set_clk_enet(ENET_125MHZ);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
setup_iomux_uart();
|
|
setup_fec();
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* address of boot parameters */
|
|
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_late_init(void)
|
|
{
|
|
struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
|
|
unsigned char eth1addr[6];
|
|
|
|
imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
|
|
|
|
set_wdog_reset(wdog);
|
|
|
|
/*
|
|
* Do not assert internal WDOG_RESET_B_DEB(controlled by bit 4),
|
|
* since we use PMIC_PWRON to reset the board.
|
|
*/
|
|
clrsetbits_le16(&wdog->wcr, 0, 0x10);
|
|
|
|
/* Get the second MAC address */
|
|
imx_get_mac_from_fuse(1, eth1addr);
|
|
if (!env_get("eth1addr") && is_valid_ethaddr(eth1addr))
|
|
eth_env_set_enetaddr("eth1addr", eth1addr);
|
|
|
|
return 0;
|
|
}
|
|
|
|
uint mmc_get_env_part(struct mmc *mmc)
|
|
{
|
|
uint part = EXT_CSD_EXTRACT_BOOT_PART(mmc->part_config);
|
|
|
|
if (part == 7)
|
|
part = 0;
|
|
return part;
|
|
}
|
|
|