0cb6515cda
Since commit [1] A53 u-boot proper is broken. This is because nodes
marked as 'bootph-pre-ram' are not available at u-boot proper before
relocation.
To fix this we mark all nodes in u-boot.dtsi as 'bootph-all'.
[1]
9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Reported-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
196 lines
2.5 KiB
Plaintext
196 lines
2.5 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* https://beagleboard.org/play
|
|
*
|
|
* Copyright (C) 2022-2023 Texas Instruments Incorporated - https://www.ti.com/
|
|
* Copyright (C) 2022-2023 Robert Nelson, BeagleBoard.org Foundation
|
|
*/
|
|
|
|
#include "k3-am625-sk-binman.dtsi"
|
|
|
|
/ {
|
|
chosen {
|
|
tick-timer = &main_timer0;
|
|
};
|
|
|
|
memory@80000000 {
|
|
bootph-all;
|
|
};
|
|
|
|
/* Keep the LEDs on by default to indicate life */
|
|
leds {
|
|
bootph-all;
|
|
led-0 {
|
|
default-state = "on";
|
|
bootph-all;
|
|
};
|
|
|
|
led-1 {
|
|
default-state = "on";
|
|
bootph-all;
|
|
};
|
|
|
|
led-2 {
|
|
default-state = "on";
|
|
bootph-all;
|
|
};
|
|
|
|
led-3 {
|
|
default-state = "on";
|
|
bootph-all;
|
|
};
|
|
|
|
led-4 {
|
|
default-state = "on";
|
|
bootph-all;
|
|
};
|
|
};
|
|
};
|
|
|
|
&cbass_main {
|
|
bootph-all;
|
|
};
|
|
|
|
&main_timer0 {
|
|
clock-frequency = <25000000>;
|
|
bootph-all;
|
|
};
|
|
|
|
&dmss {
|
|
bootph-all;
|
|
};
|
|
|
|
&secure_proxy_main {
|
|
bootph-all;
|
|
};
|
|
|
|
&dmsc {
|
|
bootph-all;
|
|
};
|
|
|
|
&k3_pds {
|
|
bootph-all;
|
|
};
|
|
|
|
&k3_clks {
|
|
bootph-all;
|
|
};
|
|
|
|
&k3_reset {
|
|
bootph-all;
|
|
};
|
|
|
|
&dmsc {
|
|
bootph-all;
|
|
k3_sysreset: sysreset-controller {
|
|
compatible = "ti,sci-sysreset";
|
|
bootph-all;
|
|
};
|
|
};
|
|
|
|
&wkup_conf {
|
|
bootph-all;
|
|
};
|
|
|
|
&chipid {
|
|
bootph-all;
|
|
};
|
|
|
|
&main_pmx0 {
|
|
bootph-all;
|
|
};
|
|
|
|
&main_uart0 {
|
|
bootph-all;
|
|
};
|
|
|
|
&console_pins_default {
|
|
bootph-all;
|
|
};
|
|
|
|
&cbass_mcu {
|
|
bootph-all;
|
|
};
|
|
|
|
&cbass_wakeup {
|
|
bootph-all;
|
|
};
|
|
|
|
&mcu_pmx0 {
|
|
bootph-all;
|
|
};
|
|
|
|
&main_i2c0 {
|
|
bootph-all;
|
|
};
|
|
|
|
&local_i2c_pins_default {
|
|
bootph-all;
|
|
};
|
|
|
|
&gpio0_pins_default {
|
|
bootph-all;
|
|
};
|
|
|
|
&main_gpio0 {
|
|
bootph-all;
|
|
};
|
|
|
|
&main_gpio1 {
|
|
bootph-all;
|
|
};
|
|
|
|
&sdhci0 {
|
|
/* EMMC */
|
|
bootph-all;
|
|
};
|
|
|
|
&emmc_pins_default {
|
|
bootph-all;
|
|
};
|
|
|
|
&sd_pins_default {
|
|
bootph-all;
|
|
/* Force to use SDCD card detect pin */
|
|
pinctrl-single,pins = <
|
|
AM62X_IOPAD(0x023c, PIN_INPUT, 0) /* (A21) MMC1_CMD */
|
|
AM62X_IOPAD(0x0234, PIN_INPUT, 0) /* (B22) MMC1_CLK */
|
|
AM62X_IOPAD(0x0230, PIN_INPUT, 0) /* (A22) MMC1_DAT0 */
|
|
AM62X_IOPAD(0x022c, PIN_INPUT, 0) /* (B21) MMC1_DAT1 */
|
|
AM62X_IOPAD(0x0228, PIN_INPUT, 0) /* (C21) MMC1_DAT2 */
|
|
AM62X_IOPAD(0x0224, PIN_INPUT, 0) /* (D22) MMC1_DAT3 */
|
|
AM62X_IOPAD(0x0240, PIN_INPUT, 0) /* (D17) MMC1_SDCD.MMC1_SDCD */
|
|
>;
|
|
};
|
|
|
|
&tps65219 {
|
|
bootph-all;
|
|
};
|
|
|
|
&sdhci1 {
|
|
bootph-all;
|
|
};
|
|
|
|
#ifdef CONFIG_TARGET_AM625_A53_EVM
|
|
|
|
#define SPL_AM625_BEAGLEPLAY_DTB "spl/dts/k3-am625-beagleplay.dtb"
|
|
#define AM625_BEAGLEPLAY_DTB "arch/arm/dts/k3-am625-beagleplay.dtb"
|
|
|
|
&spl_am625_sk_dtb {
|
|
filename = SPL_AM625_BEAGLEPLAY_DTB;
|
|
};
|
|
|
|
&am625_sk_dtb {
|
|
filename = AM625_BEAGLEPLAY_DTB;
|
|
};
|
|
|
|
&spl_am625_sk_dtb_unsigned {
|
|
filename = SPL_AM625_BEAGLEPLAY_DTB;
|
|
};
|
|
|
|
&am625_sk_dtb_unsigned {
|
|
filename = AM625_BEAGLEPLAY_DTB;
|
|
};
|
|
|
|
#endif
|