u-boot/include/axp818.h
Samuel Holland 09cbd3858f gpio: axp/sunxi: Remove virtual VBUS detection GPIO
Now that this functionality is modeled using the device tree and
regulator uclass, the named GPIO is not referenced anywhere. Remove it.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2023-04-28 01:30:24 +01:00

76 lines
2.5 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510@gmail.com>
*
* X-Powers AXP818 Power Management IC driver
*/
#define AXP818_CHIP_ID 0x03
#define AXP818_OUTPUT_CTRL1 0x10
#define AXP818_OUTPUT_CTRL1_DCDC1_EN (1 << 0)
#define AXP818_OUTPUT_CTRL1_DCDC2_EN (1 << 1)
#define AXP818_OUTPUT_CTRL1_DCDC3_EN (1 << 2)
#define AXP818_OUTPUT_CTRL1_DCDC4_EN (1 << 3)
#define AXP818_OUTPUT_CTRL1_DCDC5_EN (1 << 4)
#define AXP818_OUTPUT_CTRL1_DCDC6_EN (1 << 5)
#define AXP818_OUTPUT_CTRL1_DCDC7_EN (1 << 6)
#define AXP818_OUTPUT_CTRL2 0x12
#define AXP818_OUTPUT_CTRL2_ELDO1_EN (1 << 0)
#define AXP818_OUTPUT_CTRL2_ELDO2_EN (1 << 1)
#define AXP818_OUTPUT_CTRL2_ELDO3_EN (1 << 2)
#define AXP818_OUTPUT_CTRL2_DLDO1_EN (1 << 3)
#define AXP818_OUTPUT_CTRL2_DLDO2_EN (1 << 4)
#define AXP818_OUTPUT_CTRL2_DLDO3_EN (1 << 5)
#define AXP818_OUTPUT_CTRL2_DLDO4_EN (1 << 6)
#define AXP818_OUTPUT_CTRL2_SW_EN (1 << 7)
#define AXP818_OUTPUT_CTRL3 0x13
#define AXP818_OUTPUT_CTRL3_FLDO1_EN (1 << 2)
#define AXP818_OUTPUT_CTRL3_FLDO2_EN (1 << 3)
#define AXP818_OUTPUT_CTRL3_FLDO3_EN (1 << 4)
#define AXP818_OUTPUT_CTRL3_ALDO1_EN (1 << 5)
#define AXP818_OUTPUT_CTRL3_ALDO2_EN (1 << 6)
#define AXP818_OUTPUT_CTRL3_ALDO3_EN (1 << 7)
#define AXP818_DLDO1_CTRL 0x15
#define AXP818_DLDO2_CTRL 0x16
#define AXP818_DLDO3_CTRL 0x17
#define AXP818_DLDO4_CTRL 0x18
#define AXP818_ELDO1_CTRL 0x19
#define AXP818_ELDO2_CTRL 0x1a
#define AXP818_ELDO3_CTRL 0x1b
#define AXP818_FLDO1_CTRL 0x1c
#define AXP818_FLDO2_3_CTRL 0x1d
#define AXP818_FLDO2_3_CTRL_FLDO3_VOL (1 << 4)
#define AXP818_DCDC1_CTRL 0x20
#define AXP818_DCDC2_CTRL 0x21
#define AXP818_DCDC3_CTRL 0x22
#define AXP818_DCDC4_CTRL 0x23
#define AXP818_DCDC5_CTRL 0x24
#define AXP818_DCDC6_CTRL 0x25
#define AXP818_DCDC7_CTRL 0x26
#define AXP818_ALDO1_CTRL 0x28
#define AXP818_ALDO2_CTRL 0x29
#define AXP818_ALDO3_CTRL 0x2a
#define AXP818_SHUTDOWN 0x32
#define AXP818_SHUTDOWN_POWEROFF (1 << 7)
/* For axp_gpio.c */
#ifdef CONFIG_AXP818_POWER
#define AXP_POWER_STATUS 0x00
#define AXP_POWER_STATUS_ALDO_IN BIT(0)
#define AXP_VBUS_IPSOUT 0x30
#define AXP_VBUS_IPSOUT_DRIVEBUS (1 << 2)
#define AXP_MISC_CTRL 0x8f
#define AXP_MISC_CTRL_N_VBUSEN_FUNC (1 << 4)
#define AXP_GPIO0_CTRL 0x90
#define AXP_GPIO1_CTRL 0x92
#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */
#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */
#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */
#define AXP_GPIO_STATE 0x94
#define AXP_GPIO_STATE_OFFSET 0
#endif