Embedded_SDK
/
MCUXpresso_MIMXRT1021xxxxx
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
MCUXpresso_MIMXRT1021xxxxx/boards/evkmimxrt1020/demo_apps/xbar_aoi
History
Yilin Sun 763d32be90
Updated SDK to v2.15.000 
Signed-off-by: Yilin Sun <imi415@imi.moe>
 		2024-03-15 22:23:36 +08:00
..
armgcc Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00
board.c Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00
board.h Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00
clock_config.c Updated to SDK v2.14.0 2023-08-31 23:30:31 +08:00
clock_config.h Updated to SDK v2.14.0 2023-08-31 23:30:31 +08:00
dcd.c Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
dcd.h Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
evkmimxrt1020_sdram_init.jlinkscript Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
pin_mux.c Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
pin_mux.h Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
readme.md Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00
xbar_aoi.bin Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00
xbar_aoi.c Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
xbar_aoi.mex Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
xbar_aoi_v3_14.xml Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00

readme.md

Overview

The XBAR AOI demo application demonstrates the usage of the XBAR, AOI peripheral to combine interrupt from CMP and PIT. If the button is pressed(CMP interrupt) and the PIT periodic interrupt occurs a message is printed.

SDK version

  • Version: 2.15.000

Toolchain supported

  • IAR embedded Workbench 9.40.1
  • Keil MDK 5.38.1
  • GCC ARM Embedded 12.2
  • MCUXpresso 11.8.0

Hardware requirements

  • Mini/micro USB cable
  • MIMXRT1020-EVK board
  • Personal Computer

Board settings

No special settings are required.

Prepare the Demo

  1. Connect a USB cable between the host PC and the OpenSDA USB port on the target board.
  2. Open a serial terminal with the following settings:
    • 115200 baud rate
    • 8 data bits
    • No parity
    • One stop bit
    • No flow control
  3. Download the program to the target board.
  4. Either press the reset button on your board or launch the debugger in your IDE to begin running the demo.

Running the demo

The log below shows the output of the xbar aoi demo in the terminal window:

XBAR and AOI Demo: Start...

Then change CMP analog input.
    - CMP1_IN0 (J17-7) connected to VCC =3.3V (J19-8): XBAR interrupt occurred
    - CMP1_IN0 (J17-7) connected to GND (J19-7): XBAT interrupt stopped

XBAR interrupt occurred

XBAR interrupt occurred