Embedded_SDK
/
MCUXpresso_MIMXRT1021xxxxx
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
MCUXpresso_MIMXRT1021xxxxx/boards/evkmimxrt1020/driver_examples/ewm
History
Yilin Sun 763d32be90
Updated SDK to v2.15.000 
Signed-off-by: Yilin Sun <imi415@imi.moe>
 		2024-03-15 22:23:36 +08:00
..
armgcc Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00
board.c Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00
board.h Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00
clock_config.c Updated to SDK v2.14.0 2023-08-31 23:30:31 +08:00
clock_config.h Updated to SDK v2.14.0 2023-08-31 23:30:31 +08:00
dcd.c Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
dcd.h Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
evkmimxrt1020_sdram_init.jlinkscript Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
ewm.c Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
ewm_v3_14.xml Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00
pin_mux.c Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
pin_mux.h Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
readme.md Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00

readme.md

Overview

The EWM Example project is to demonstrate usage of the KSDK EWM driver. In the example, EWM counter is continuously refreshed until button is pressed. Once the button is pressed, EWM counter will expire and interrupt will be generated. After the first pressing, another interrupt can be triggered by pressing button again.

Note: In flash boot mode, if you want to use the IDE reset program, please use systemReset.

SDK version

  • Version: 2.15.000

Toolchain supported

  • IAR embedded Workbench 9.40.1
  • Keil MDK 5.38.1
  • GCC ARM Embedded 12.2
  • MCUXpresso 11.8.0

Hardware requirements

  • Mini/micro USB cable
  • EVK-MIMXRT1020 board
  • Personal Computer

Board settings

No special settings are required.

Prepare the Demo

  1. Connect a USB cable between the host PC and the OpenSDA USB port on the target board.
  2. Open a serial terminal with the following settings:
    • 115200 baud rate
    • 8 data bits
    • No parity
    • One stop bit
    • No flow control
  3. Download the program to the target board.
  4. Either press the reset button on your board or launch the debugger in your IDE to begin running the demo.

Running the demo

When the example runs successfully, you can see the similar information from the terminal as below.

Press anykey to start the example...

EWM example
Press SW4 to expire EWM
EWM interrupt is occurred
Press SW4 to expire EWM again

Note: To debug in qspiflash, following steps are needed:

  1. Select the flash target and compile.
  2. Set the SW8: 1 off 2 off 3 on 4 off, then power on the board and connect USB cable to J23.
  3. Start debugging in IDE.
    • Keil: Click "Download (F8)" to program the image to qspiflash first then clicking "Start/Stop Debug Session (Ctrl+F5)" to start debugging.