Embedded_SDK/MCUXpresso_MIMXRT1021xxxxx
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
master
MCUXpresso_MIMXRT1021xxxxx/boards/evkmimxrt1020/driver_examples/gpt/capture
History
Yilin Sun 763d32be90
Updated SDK to v2.15.000 
Signed-off-by: Yilin Sun <imi415@imi.moe>
2024-03-15 22:23:36 +08:00
..
armgcc Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00
board.c Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00
board.h Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00
clock_config.c Updated to SDK v2.14.0 2023-08-31 23:30:31 +08:00
clock_config.h Updated to SDK v2.14.0 2023-08-31 23:30:31 +08:00
dcd.c Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
dcd.h Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
evkmimxrt1020_sdram_init.jlinkscript Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
gpt_capture_v3_14.xml Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00
gpt_capture.c Updated to SDK v2.14.0 2023-08-31 23:30:31 +08:00
pin_mux.c Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
pin_mux.h Initial SDK v2.12.0 2022-08-23 23:00:33 +08:00
readme.md Updated SDK to v2.15.000 2024-03-15 22:23:36 +08:00

readme.md

Overview

The gpt_capture project is a simple demonstration program of the SDK GPT driver's input capture feature. The example sets up a GPT channel for rise-edge capture. Once the input signal is received, this example will print the capture value.

SDK version

  • Version: 2.15.000

Toolchain supported

  • IAR embedded Workbench 9.40.1
  • Keil MDK 5.38.1
  • GCC ARM Embedded 12.2
  • MCUXpresso 11.8.0

Hardware requirements

  • Micro USB cable
  • EVK-MIMXRT1020 board
  • Personal Computer

Board settings

Connect input signal to J18-2 Test Point.

Prepare the Demo

  1. Connect a USB cable between the host PC and the OpenSDA USB port on the target board.
  2. Open a serial terminal with the following settings:
    • 115200 baud rate
    • 8 data bits
    • No parity
    • One stop bit
    • No flow control
  3. Download the program to the target board.
  4. Either press the reset button on your board or launch the debugger in your IDE to begin running the demo.

Running the demo

When the example runs successfully, following information can be seen on the terminal:

GPT input capture example
Once the input signal is received the input capture value is printed

Note: To debug in qspiflash, following steps are needed:

  1. Select the flash target and compile.
  2. Set the SW8: 1 off 2 off 3 on 4 off, then power on the board and connect USB cable to J23.
  3. Start debugging in IDE.
    • Keil: Click "Download (F8)" to program the image to qspiflash first then clicking "Start/Stop Debug Session (Ctrl+F5)" to start debugging.