Overview
========
The enet_rxtx_ptp1588 example shows the way to use ENET driver to
receive and transmit frame in the 1588 feature required cases.
1. This example shows how to initialize the ENET MAC.
2. How to use ENET MAC to receive and transmit frame.
3. How to add to the multicast group to receive PTP 1588 message.
4. How to get the time stamp of the PTP 1588 timer.
4. How to use Get the ENET transmit and receive frame time stamp.
The example transmits 20 number PTP event frame, shows the timestamp of the transmitted frame.
The length, source MAC address and destination MAC address of the received frame will be print.
The time stamp of the received timestamp will be print when the PTP message frame is received.
Note, The RMII mode is used for default setting to initialize the ENET interface between MAC and the external PHY. you
can change it to MII mode as you wish. Please make sure the MII Mode setting in the MAC is synchronize to the setting
in TWR-SERIAL board for the external PHY.
Toolchain supported
===================
- IAR embedded Workbench 9.30.1
- Keil MDK 5.37
- GCC ARM Embedded 10.3.1
- MCUXpresso 11.6.0
Hardware requirements
=====================
- Mini/micro USB cable
- Loopback network cable RJ45 standard
- EVK-MIMXRT1020 board
- Personal Computer
Board settings
==============
No special settings are required.
Prepare the Demo
================
1. Connect a USB cable between the host PC and the OpenSDA USB port on the target board.
2. Open a serial terminal with the following settings:
- 115200 baud rate
- 8 data bits
- No parity
- One stop bit
- No flow control
3. Insert loopback network cable to Ethernet RJ45 port.
4. Download the program to the target board.
5. Either press the reset button on your board or launch the debugger in your IDE to begin running the demo.
Make loopback network cable:
568B standard Unknowed standard
J1 orange+white green+white
J2 orange green
J3 green+white orange+white
J4 blue brown+white
J5 blue+white brown
J6 green orange
J7 brown+white blue
J8 brown blue+white
Connect J1 => J3, J2 => J6, J4 => J7, J5 => J8. 10/100M transfer only requires J1, J2, J3, J6, and 1G transfer requires all 8 pins.
Check your net cable color order and refer to 568B standard or the other standard. If your cable's color order is not showed in the list,
please connect J1~J8 based on your situation.
Note:
To debug in qspiflash, following steps are needed:
1. Select the flash target and compile.
2. Set the SW8: 1 off 2 off 3 on 4 off, then power on the board and connect USB cable to J23.
3. Start debugging in IDE.
- Keil: Click "Download (F8)" to program the image to qspiflash first then clicking "Start/Stop Debug Session (Ctrl+F5)" to start debugging.
Running the demo
================
When the demo runs, the log would be seen on the terminal like:
ENET PTP 1588 example start.
Get the 1-th time xx second xx nanosecond
........
Get the 10-th time xx second xx nanosecond
The 1 frame transmitted success! the timestamp is xx second, xx nanosecond
The 2 frame transmitted success! the timestamp is xx second, xx nanosecond
The 3 frame transmitted success! the timestamp is xx second, xx nanosecond
The 4 frame transmitted success! the timestamp is xx second, xx nanosecond
......
The 20 frame transmitted success! the timestamp is xx second, xx nanosecond
Note: the xx second and xx nanosecond should not be zero and should be number with solid increment.
when a 1000 length ptp event message frame is received, the log would be added to the terminal like:
A frame received. the length 1000 the timestamp is xx second, xx nanosecond
Dest Address xx:xx:xx:xx:xx:xx Src Address xx:xx:xx:xx:xx:xx
A frame received. the length 1000 Dest Address xx:xx:xx:xx:xx:xx Src Address xx:xx:xx:xx:xx:xx
