Embedded_SDK
/
MCUXpresso_MIMXRT1052xxxxB
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
MCUXpresso_MIMXRT1052xxxxB/boards/evkbimxrt1050/sdmmc_examples/sdcard_fatfs
History
Yilin Sun 6baf4427ce
Updated to v2.15.000 
Signed-off-by: Yilin Sun <imi415@imi.moe>
 		2024-03-18 23:15:10 +08:00
..
armgcc Updated to v2.15.000 2024-03-18 23:15:10 +08:00
board.c Updated to v2.15.000 2024-03-18 23:15:10 +08:00
board.h Updated to v2.15.000 2024-03-18 23:15:10 +08:00
clock_config.c Update SDK to v2.13.0 2023-01-26 09:35:56 +08:00
clock_config.h Update SDK to v2.13.0 2023-01-26 09:35:56 +08:00
dcd.c SDK v2.11.1 2022-04-08 22:46:35 +08:00
dcd.h SDK v2.11.1 2022-04-08 22:46:35 +08:00
evkbimxrt1050_sdram_init.jlinkscript Updated to v2.14.0 2023-11-30 20:55:00 +08:00
ffconf.h Updated to v2.15.000 2024-03-18 23:15:10 +08:00
pin_mux.c SDK v2.11.1 2022-04-08 22:46:35 +08:00
pin_mux.h SDK v2.11.1 2022-04-08 22:46:35 +08:00
readme.md Updated to v2.15.000 2024-03-18 23:15:10 +08:00
sdcard_fatfs.c SDK v2.11.1 2022-04-08 22:46:35 +08:00
sdcard_fatfs_v3_14.xml Updated to v2.15.000 2024-03-18 23:15:10 +08:00
sdmmc_config.c Updated to v2.12.0 2022-08-24 23:30:23 +08:00
sdmmc_config.h Updated to v2.14.0 2023-11-30 20:55:00 +08:00

readme.md

Overview

The SDCARD FATFS project is a demonstration program that uses the SDK software. It mounts a file system based on a SD card then does "creat directory/read directory/create file/write file/read file" operation. The file sdhc_config.h has default SDHC configuration which can be adjusted to let card driver has different performance. The purpose of this example is to show how to use SDCARD driver based FATFS disk in SDK software.

SDK version

  • Version: 2.15.000

Toolchain supported

  • IAR embedded Workbench 9.40.1
  • Keil MDK 5.38.1
  • GCC ARM Embedded 12.2
  • MCUXpresso 11.8.0

Hardware requirements

  • Mini/micro USB cable
  • EVKB-IMXRT1050 board
  • Personal Computer
  • SD card

Board settings

Please insert the SDCARD into card slot(J20) Note: If you want to use a SD3.0 card with SD3.0 protocol, just insert a SD3.0 card into the card slot will be ok.

Prepare the Demo

  1. Connect a micro USB cable between the PC host and the OpenSDA USB port on the board.
  2. Open a serial terminal on PC for OpenSDA serial device with these settings:
    • 115200 baud rate
    • 8 data bits
    • No parity
    • One stop bit
    • No flow control
  3. Insert SD card to card slot
  4. Download the program to the target board.
  5. Either press the reset button on your board or launch the debugger in your IDE to begin running the demo.

Running the demo

When the demo runs successfully, the log would be seen on the terminal like:


FATFS example to demonstrate how to use FATFS with SD card.

Please insert a card into board.
Detected SD card inserted.

Makes file system......This time may be long if the card capacity is big.

Creates directory......

Creates a file in that directory......

Lists the file in that directory......
General file : F_1.DAT.
Directory file : DIR_2.

Writes/reads file until encounters error......

Writes to above created file.
Reads from above created file.
Compares the read/write content......
The read/write content is consistent.
Input 'q' to quit read/write.
Input other char to read/write file again.