130 lines
9.7 KiB
C
130 lines
9.7 KiB
C
/*
|
|
* Copyright 2017-2021 NXP
|
|
* All rights reserved.
|
|
*
|
|
* SPDX-License-Identifier: BSD-3-Clause
|
|
*/
|
|
|
|
/***********************************************************************************************************************
|
|
* This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file
|
|
* will be overwritten if the respective MCUXpresso Config Tools is used to update this file.
|
|
**********************************************************************************************************************/
|
|
|
|
/*
|
|
* TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
|
|
!!GlobalInfo
|
|
product: Pins v9.0
|
|
processor: MIMXRT1052xxxxB
|
|
package_id: MIMXRT1052DVL6B
|
|
mcu_data: ksdk2_0
|
|
processor_version: 0.0.0
|
|
* BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
|
|
*/
|
|
|
|
#include "fsl_common.h"
|
|
#include "fsl_iomuxc.h"
|
|
#include "pin_mux.h"
|
|
|
|
/* FUNCTION ************************************************************************************************************
|
|
*
|
|
* Function Name : BOARD_InitBootPins
|
|
* Description : Calls initialization functions.
|
|
*
|
|
* END ****************************************************************************************************************/
|
|
void BOARD_InitBootPins(void) {
|
|
BOARD_InitPins();
|
|
}
|
|
|
|
/*
|
|
* TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
|
|
BOARD_InitPins:
|
|
- options: {callFromInitBoot: 'true', coreID: core0, enableClock: 'true'}
|
|
- pin_list:
|
|
- {pin_num: L14, peripheral: LPUART1, signal: RX, pin_signal: GPIO_AD_B0_13, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
|
|
pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
|
|
- {pin_num: K14, peripheral: LPUART1, signal: TX, pin_signal: GPIO_AD_B0_12, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
|
|
pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
|
|
- {pin_num: J11, peripheral: LPI2C1, signal: SCL, pin_signal: GPIO_AD_B1_00, software_input_on: Enable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_22K_Ohm,
|
|
pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Enable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
|
|
- {pin_num: K11, peripheral: LPI2C1, signal: SDA, pin_signal: GPIO_AD_B1_01, software_input_on: Enable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_22K_Ohm,
|
|
pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Enable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
|
|
- {pin_num: M13, peripheral: SAI1, signal: sai_mclk, pin_signal: GPIO_AD_B1_09, software_input_on: Enable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
|
|
pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
|
|
- {pin_num: G12, peripheral: SAI1, signal: sai_tx_bclk, pin_signal: GPIO_AD_B1_14, software_input_on: Enable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
|
|
pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
|
|
- {pin_num: H11, peripheral: SAI1, signal: sai_tx_data0, pin_signal: GPIO_AD_B1_13, software_input_on: Enable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
|
|
pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
|
|
- {pin_num: J14, peripheral: SAI1, signal: sai_tx_sync, pin_signal: GPIO_AD_B1_15, software_input_on: Enable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
|
|
pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
|
|
- {pin_num: H12, peripheral: SAI1, signal: sai_rx_data0, pin_signal: GPIO_AD_B1_12, software_input_on: Enable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
|
|
pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
|
|
- {pin_num: D13, peripheral: GPIO2, signal: 'gpio_io, 28', pin_signal: GPIO_B1_12, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm,
|
|
pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0, slew_rate: Fast}
|
|
- {pin_num: J3, peripheral: USDHC1, signal: usdhc_clk, pin_signal: GPIO_SD_B0_01, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm,
|
|
pull_keeper_select: Keeper, pull_keeper_enable: Disable, open_drain: Disable, speed: MHZ_100, drive_strength: R0, slew_rate: Fast}
|
|
- {pin_num: J4, peripheral: USDHC1, signal: usdhc_cmd, pin_signal: GPIO_SD_B0_00, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm,
|
|
pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0, slew_rate: Fast}
|
|
- {pin_num: J1, peripheral: USDHC1, signal: 'usdhc_data, 0', pin_signal: GPIO_SD_B0_02, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm,
|
|
pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0, slew_rate: Fast}
|
|
- {pin_num: K1, peripheral: USDHC1, signal: 'usdhc_data, 1', pin_signal: GPIO_SD_B0_03, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm,
|
|
pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0, slew_rate: Fast}
|
|
- {pin_num: H2, peripheral: USDHC1, signal: 'usdhc_data, 2', pin_signal: GPIO_SD_B0_04, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm,
|
|
pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0, slew_rate: Fast}
|
|
- {pin_num: J2, peripheral: USDHC1, signal: 'usdhc_data, 3', pin_signal: GPIO_SD_B0_05, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm,
|
|
pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0, slew_rate: Fast}
|
|
- {pin_num: C14, peripheral: USDHC1, signal: usdhc_vselect, pin_signal: GPIO_B1_14, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_47K_Ohm,
|
|
pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_4, slew_rate: Fast}
|
|
* BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
|
|
*/
|
|
|
|
/* FUNCTION ************************************************************************************************************
|
|
*
|
|
* Function Name : BOARD_InitPins
|
|
* Description : Configures pin routing and optionally pin electrical features.
|
|
*
|
|
* END ****************************************************************************************************************/
|
|
void BOARD_InitPins(void) {
|
|
CLOCK_EnableClock(kCLOCK_Iomuxc);
|
|
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B0_05_GPIO1_IO05, 0U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B0_12_LPUART1_TXD, 0U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B0_13_LPUART1_RXD, 0U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_B1_12_GPIO2_IO28, 0U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B1_00_LPI2C1_SCL, 1U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B1_01_LPI2C1_SDA, 1U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B1_09_SAI1_MCLK, 1U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B1_12_SAI1_RX_DATA00, 1U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B1_13_SAI1_TX_DATA00, 1U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B1_14_SAI1_TX_BCLK, 1U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_AD_B1_15_SAI1_TX_SYNC, 1U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_B1_14_USDHC1_VSELECT, 0U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_SD_B0_00_USDHC1_CMD, 0U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_SD_B0_01_USDHC1_CLK, 0U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_SD_B0_02_USDHC1_DATA0, 0U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_SD_B0_03_USDHC1_DATA1, 0U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_SD_B0_04_USDHC1_DATA2, 0U);
|
|
IOMUXC_SetPinMux(IOMUXC_GPIO_SD_B0_05_USDHC1_DATA3, 0U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_AD_B0_05_GPIO1_IO05, 0x10B0U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_AD_B0_12_LPUART1_TXD, 0x10B0U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_AD_B0_13_LPUART1_RXD, 0x10B0U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_B1_12_GPIO2_IO28, 0x017089U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_AD_B1_00_LPI2C1_SCL, 0xD8B0U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_AD_B1_01_LPI2C1_SDA, 0xD8B0U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_AD_B1_09_SAI1_MCLK, 0x10B0U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_AD_B1_12_SAI1_RX_DATA00, 0x10B0U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_AD_B1_13_SAI1_TX_DATA00, 0x10B0U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_AD_B1_14_SAI1_TX_BCLK, 0x10B0U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_AD_B1_15_SAI1_TX_SYNC, 0x10B0U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_B1_14_USDHC1_VSELECT, 0x0170A1U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_SD_B0_00_USDHC1_CMD, 0x017089U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_SD_B0_01_USDHC1_CLK, 0x014089U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_SD_B0_02_USDHC1_DATA0, 0x017089U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_SD_B0_03_USDHC1_DATA1, 0x017089U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_SD_B0_04_USDHC1_DATA2, 0x017089U);
|
|
IOMUXC_SetPinConfig(IOMUXC_GPIO_SD_B0_05_USDHC1_DATA3, 0x017089U);
|
|
}
|
|
|
|
/***********************************************************************************************************************
|
|
* EOF
|
|
**********************************************************************************************************************/
|