michal smulski <michal.smulski@ooma.com> reset now works

git-svn-id: svn://svn.berlios.de/openocd/trunk@2778 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This commit is contained in:
oharboe 2009-09-30 05:37:32 +00:00
parent e4de4251fe
commit 642519649e
3 changed files with 213 additions and 68 deletions

View File

@ -1,33 +1,34 @@
source [find target/c100.cfg]
source [find c100.cfg]
# basic register defintion for C100
source [find target/c100regs.tcl]
source [find c100regs.tcl]
# board-config info
source [find target/c100config.tcl]
source [find c100config.tcl]
# C100 helper functions
source [find target/c100helper.tcl]
source [find c100helper.tcl]
# Telo board & C100 support trst and srst
# however openocd does not support
# 1. setting srst reset pulse width
# 2. setting delay between srst pulse and JTAG access
# This really makes the srst useless for now.
# Note that libftd2xx.so tries to assert srst
# which break this script
# use libftdi.so library instead with this script
# make the reset asserted to
# allow RC circuit to discharge for: [ms]
jtag_nsrst_assert_width 100
jtag_ntrst_assert_width 100
# don't talk to JTAG after reset for: [ms]
jtag_nsrst_delay 100
jtag_ntrst_delay 100
reset_config trst_and_srst separate
# issue telnet: reset init
# issue gdb: monitor reset init
$_TARGETNAME configure -event reset-init {
jtag_khz 100
# setup GPIO used as control signals for C100
setupGPIO
# This will allow acces to lower 8MB or NOR
lowGPIO5
# setup NOR size,timing,etc.
setupNOR
# setup internals + PLL + DDR2
initC100
# this will setup Telo board
setupTelo
#turn up the JTAG speed
jtag_khz 3000
puts "JTAG speek now 3MHz"
@ -38,10 +39,15 @@ $_TARGETNAME configure -event reset-deassert-post {
# Force target into ARM state.
# soft_reset_halt # not implemented on ARM11
puts "Detected SRSRT asserted on C100.CPU"
}
proc power_restore {} { puts "Sensed power restore. No action." }
$_TARGETNAME configure -event reset-assert-post {
puts "Assering reset"
#sleep 10
}
proc power_restore {} { puts "Sensed power restore. No action." }
proc srst_deasserted {} { puts "Sensed nSRST deasserted. No action." }

View File

@ -3,7 +3,7 @@
# set CFG_REFCLKFREQ [configC100 CFG_REFCLKFREQ]
proc config {label} {
return [dict get [configC100] $label ]
return [dict get [configC100] $label ]
}
# show the value for the param. with label
@ -15,7 +15,7 @@ proc showconfig {label} {
# when there are more then one board config
# use soft links to c100board-config.tcl
# so that only the right board-config gets
# included (just like include/configs/board-configs.h
# included (just like include/configs/board-configs.h
# in u-boot.
proc configC100 {} {
# xtal freq. 24MHz
@ -28,7 +28,7 @@ proc configC100 {} {
# y = amba_clk * (w+1)*(x+1)*2/xtal_clk
dict set configC100 y_amba [expr ([dict get $configC100 CONFIG_SYS_HZ_CLOCK] * ( ([dict get $configC100 w_amba]+1 ) * ([dict get $configC100 x_amba]+1 ) *2 ) / [dict get $configC100 CFG_REFCLKFREQ]) ]
# Arm Clk 450MHz, must be a multiple of 25 MHz
# Arm Clk 450MHz, must be a multiple of 25 MHz
dict set configC100 CFG_ARM_CLOCK 450000000
dict set configC100 w_arm 0
dict set configC100 x_arm 1
@ -38,20 +38,34 @@ proc configC100 {} {
}
# This should be called for reset init event handler
proc setupTelo {} {
# setup GPIO used as control signals for C100
setupGPIO
# This will allow acces to lower 8MB or NOR
lowGPIO5
# setup NOR size,timing,etc.
setupNOR
# setup internals + PLL + DDR2
initC100
}
proc setupNOR {} {
puts "Setting up NOR: 16MB, 16-bit wide bus, CS0"
# this is taken from u-boot/boards/mindspeed/ooma-darwin/board.c:nor_hw_init()
set EX_CSEN_REG [regs EX_CSEN_REG ]
set EX_CS0_SEG_REG [regs EX_CS0_SEG_REG ]
set EX_CS0_CFG_REG [regs EX_CS0_CFG_REG ]
set EX_CS0_TMG1_REG [regs EX_CS0_TMG1_REG ]
set EX_CS0_TMG2_REG [regs EX_CS0_TMG2_REG ]
set EX_CS0_TMG3_REG [regs EX_CS0_TMG3_REG ]
set EX_CSEN_REG [regs EX_CSEN_REG ]
set EX_CS0_SEG_REG [regs EX_CS0_SEG_REG ]
set EX_CS0_CFG_REG [regs EX_CS0_CFG_REG ]
set EX_CS0_TMG1_REG [regs EX_CS0_TMG1_REG ]
set EX_CS0_TMG2_REG [regs EX_CS0_TMG2_REG ]
set EX_CS0_TMG3_REG [regs EX_CS0_TMG3_REG ]
set EX_CLOCK_DIV_REG [regs EX_CLOCK_DIV_REG ]
set EX_MFSM_REG [regs EX_MFSM_REG ]
set EX_CSFSM_REG [regs EX_CSFSM_REG ]
set EX_WRFSM_REG [regs EX_WRFSM_REG ]
set EX_RDFSM_REG [regs EX_RDFSM_REG ]
set EX_MFSM_REG [regs EX_MFSM_REG ]
set EX_CSFSM_REG [regs EX_CSFSM_REG ]
set EX_WRFSM_REG [regs EX_WRFSM_REG ]
set EX_RDFSM_REG [regs EX_RDFSM_REG ]
# enable Expansion Bus Clock + CS0 (NOR)
mww $EX_CSEN_REG 0x3
@ -62,7 +76,7 @@ proc setupNOR {} {
# set timings to NOR
mww $EX_CS0_TMG1_REG 0x03034006
mww $EX_CS0_TMG2_REG 0x04040002
#mww $EX_CS0_TMG3_REG
#mww $EX_CS0_TMG3_REG
# set EBUS clock 165/5=33MHz
mww $EX_CLOCK_DIV_REG 0x5
# everthing else is OK with default
@ -72,7 +86,7 @@ proc bootNOR {} {
set EXP_CS0_BASEADDR [regs EXP_CS0_BASEADDR]
set BLOCK_RESET_REG [regs BLOCK_RESET_REG]
set DDR_RST [regs DDR_RST]
# put DDR controller in reset (so that it comes reset in u-boot)
mmw $BLOCK_RESET_REG 0x0 $DDR_RST
# setup CS0 controller for NOR
@ -93,8 +107,8 @@ proc setupGPIO {} {
#GPIO17 reset for DECT module.
#GPIO29 CS_n for NAND
set GPIO_OUTPUT_REG [regs GPIO_OUTPUT_REG]
set GPIO_OE_REG [regs GPIO_OE_REG]
set GPIO_OUTPUT_REG [regs GPIO_OUTPUT_REG]
set GPIO_OE_REG [regs GPIO_OE_REG]
# set GPIO29=GPIO17=1, GPIO5=0
mww $GPIO_OUTPUT_REG [expr 1<<29 | 1<<17]
@ -104,14 +118,14 @@ proc setupGPIO {} {
proc highGPIO5 {} {
puts "GPIO5 high"
set GPIO_OUTPUT_REG [regs GPIO_OUTPUT_REG]
set GPIO_OUTPUT_REG [regs GPIO_OUTPUT_REG]
# set GPIO5=1
mmw $GPIO_OUTPUT_REG [expr 1 << 5] 0x0
}
proc lowGPIO5 {} {
puts "GPIO5 low"
set GPIO_OUTPUT_REG [regs GPIO_OUTPUT_REG]
set GPIO_OUTPUT_REG [regs GPIO_OUTPUT_REG]
# set GPIO5=0
mmw $GPIO_OUTPUT_REG 0x0 [expr 1 << 5]
}
@ -119,31 +133,32 @@ proc lowGPIO5 {} {
proc boardID {id} {
# so far built:
# 4'b1111
dict set boardID 15 name "EVT1"
dict set boardID 15 name "EVT1"
dict set boardID 15 ddr2size 128M
# dict set boardID 15 nandsize 1G
# dict set boardID 15 norsize 16M
# 4'b0000
dict set boardID 0 name "EVT2"
dict set boardID 0 name "EVT2"
dict set boardID 0 ddr2size 128M
# 4'b0001
dict set boardID 1 name "EVT3"
dict set boardID 1 name "EVT3"
dict set boardID 1 ddr2size 256M
# 4'b1110
dict set boardID 14 name "EVT3_old"
dict set boardID 14 ddr2size 128M
# 4'b0010
dict set boardID 2 name "EVT4"
dict set boardID 2 name "EVT4"
dict set boardID 2 ddr2size 256M
return $boardID
}
# converted from u-boot/boards/mindspeed/ooma-darwin/board.c:ooma_board_detect()
# figure out what board revision this is, uses BOOTSTRAP register to read stuffed resistors
# figure out what board revision this is, uses BOOTSTRAP register to read stuffed resistors
proc ooma_board_detect {} {
set GPIO_BOOTSTRAP_REG [regs GPIO_BOOTSTRAP_REG]
# read the current value of the BOOTSRAP pins
set tmp [mrw $GPIO_BOOTSTRAP_REG]
puts [format "GPIO_BOOTSTRAP_REG (0x%x): 0x%x" $GPIO_BOOTSTRAP_REG $tmp]
@ -152,12 +167,77 @@ proc ooma_board_detect {} {
# display board ID
puts [format "This is %s (0x%x)" [dict get [boardID $gpbt] $gpbt name] $gpbt]
# show it on serial console
putsUART0 [format "This is %s (0x%x)\n" [dict get [boardID $gpbt] $gpbt name] $gpbt]
# return the ddr2 size, used to configure DDR2 on a given board.
return [dict get [boardID $gpbt] $gpbt ddr2size]
}
proc configureDDR2regs_256M {} {
puts "ConfigureDDR2regs_256M TBD"
set DENALI_CTL_00_DATA [regs DENALI_CTL_00_DATA]
set DENALI_CTL_01_DATA [regs DENALI_CTL_01_DATA]
set DENALI_CTL_02_DATA [regs DENALI_CTL_02_DATA]
set DENALI_CTL_03_DATA [regs DENALI_CTL_03_DATA]
set DENALI_CTL_04_DATA [regs DENALI_CTL_04_DATA]
set DENALI_CTL_05_DATA [regs DENALI_CTL_05_DATA]
set DENALI_CTL_06_DATA [regs DENALI_CTL_06_DATA]
set DENALI_CTL_07_DATA [regs DENALI_CTL_07_DATA]
set DENALI_CTL_08_DATA [regs DENALI_CTL_08_DATA]
set DENALI_CTL_09_DATA [regs DENALI_CTL_09_DATA]
set DENALI_CTL_10_DATA [regs DENALI_CTL_10_DATA]
set DENALI_CTL_11_DATA [regs DENALI_CTL_11_DATA]
set DENALI_CTL_12_DATA [regs DENALI_CTL_12_DATA]
set DENALI_CTL_13_DATA [regs DENALI_CTL_13_DATA]
set DENALI_CTL_14_DATA [regs DENALI_CTL_14_DATA]
set DENALI_CTL_15_DATA [regs DENALI_CTL_15_DATA]
set DENALI_CTL_16_DATA [regs DENALI_CTL_16_DATA]
set DENALI_CTL_17_DATA [regs DENALI_CTL_17_DATA]
set DENALI_CTL_18_DATA [regs DENALI_CTL_18_DATA]
set DENALI_CTL_19_DATA [regs DENALI_CTL_19_DATA]
set DENALI_CTL_20_DATA [regs DENALI_CTL_20_DATA]
set DENALI_CTL_02_VAL 0x0100000000010100
set DENALI_CTL_11_VAL 0x433a32164a560a00
mw64bit $DENALI_CTL_00_DATA 0x0100000101010101
# 01_DATA mod [40]=1, enable BA2
mw64bit $DENALI_CTL_01_DATA 0x0100010100000001
mw64bit $DENALI_CTL_02_DATA $DENALI_CTL_02_VAL
mw64bit $DENALI_CTL_03_DATA 0x0102020202020201
mw64bit $DENALI_CTL_04_DATA 0x0000010100000001
mw64bit $DENALI_CTL_05_DATA 0x0203010300010101
mw64bit $DENALI_CTL_06_DATA 0x060a020200020202
mw64bit $DENALI_CTL_07_DATA 0x0000000300000206
mw64bit $DENALI_CTL_08_DATA 0x6400003f3f0a0209
mw64bit $DENALI_CTL_09_DATA 0x1a000000001a1a1a
mw64bit $DENALI_CTL_10_DATA 0x0120202020191a18
# 11_DATA mod [39-32]=16,more refresh
mw64bit $DENALI_CTL_11_DATA $DENALI_CTL_11_VAL
mw64bit $DENALI_CTL_12_DATA 0x0000000000000800
mw64bit $DENALI_CTL_13_DATA 0x0010002000100040
mw64bit $DENALI_CTL_14_DATA 0x0010004000100040
mw64bit $DENALI_CTL_15_DATA 0x04f8000000000000
mw64bit $DENALI_CTL_16_DATA 0x000000002cca0000
mw64bit $DENALI_CTL_17_DATA 0x0000000000000000
mw64bit $DENALI_CTL_18_DATA 0x0302000000000000
mw64bit $DENALI_CTL_19_DATA 0x00001300c8030600
mw64bit $DENALI_CTL_20_DATA 0x0000000081fe00c8
set wr_dqs_shift 0x40
# start DDRC
mw64bit $DENALI_CTL_02_DATA [expr $DENALI_CTL_02_VAL | (1 << 32)]
# wait int_status[2] (DRAM init complete)
puts -nonewline "Waiting for DDR2 controller to init..."
set tmp [mrw [expr $DENALI_CTL_08_DATA + 4]]
while { [expr $tmp & 0x040000] == 0 } {
sleep 1
set tmp [mrw [expr $DENALI_CTL_08_DATA + 4]]
}
puts "done."
# do ddr2 training sequence
# TBD (for now, if you need it, run trainDDR command)
}
# converted from u-boot/cpu/arm1136/comcerto/bsp100.c:config_board99()
@ -187,9 +267,9 @@ proc configureDDR2regs_128M {} {
set DENALI_CTL_20_DATA [regs DENALI_CTL_20_DATA]
set DENALI_CTL_02_VAL 0x0100010000010100
set DENALI_CTL_02_VAL 0x0100010000010100
set DENALI_CTL_11_VAL 0x433A42124A650A37
# set some default values
# set some default values
mw64bit $DENALI_CTL_00_DATA 0x0100000101010101
mw64bit $DENALI_CTL_01_DATA 0x0100000100000101
mw64bit $DENALI_CTL_02_DATA $DENALI_CTL_02_VAL
@ -218,11 +298,12 @@ proc configureDDR2regs_128M {} {
# wait int_status[2] (DRAM init complete)
puts -nonewline "Waiting for DDR2 controller to init..."
set tmp [mrw [expr $DENALI_CTL_08_DATA + 4]]
while { [expr $tmp & 0x040000] == 0 } {
while { [expr $tmp & 0x040000] == 0 } {
sleep 1
set tmp [mrw [expr $DENALI_CTL_08_DATA + 4]]
}
mw64bit $DENALI_CTL_11_DATA [expr ($DENALI_CTL_11_VAL & ~0x00007F0000000000) | ($wr_dqs_shift << 40) ]
# This is not necessary
#mw64bit $DENALI_CTL_11_DATA [expr ($DENALI_CTL_11_VAL & ~0x00007F0000000000) | ($wr_dqs_shift << 40) ]
puts "done."
# do ddr2 training sequence
@ -237,18 +318,18 @@ proc setupUART0 {} {
set GPIO_IOCTRL_REG [regs GPIO_IOCTRL_REG]
set GPIO_IOCTRL_VAL [regs GPIO_IOCTRL_VAL]
set GPIO_IOCTRL_UART0 [regs GPIO_IOCTRL_UART0]
set UART0_LCR [regs UART0_LCR]
set LCR_DLAB [regs LCR_DLAB]
set UART0_DLL [regs UART0_DLL]
set UART0_DLH [regs UART0_DLH]
set UART0_IIR [regs UART0_IIR]
set UART0_IER [regs UART0_IER]
set LCR_ONE_STOP [regs LCR_ONE_STOP]
set LCR_CHAR_LEN_8 [regs LCR_CHAR_LEN_8]
set UART0_LCR [regs UART0_LCR]
set LCR_DLAB [regs LCR_DLAB]
set UART0_DLL [regs UART0_DLL]
set UART0_DLH [regs UART0_DLH]
set UART0_IIR [regs UART0_IIR]
set UART0_IER [regs UART0_IER]
set LCR_ONE_STOP [regs LCR_ONE_STOP]
set LCR_CHAR_LEN_8 [regs LCR_CHAR_LEN_8]
set FCR_XMITRES [regs FCR_XMITRES]
set FCR_RCVRRES [regs FCR_RCVRRES]
set FCR_FIFOEN [regs FCR_FIFOEN]
set IER_UUE [regs IER_UUE]
set FCR_RCVRRES [regs FCR_RCVRRES]
set FCR_FIFOEN [regs FCR_FIFOEN]
set IER_UUE [regs IER_UUE]
# unlock writing to IOCTRL register
mww $GPIO_LOCK_REG $GPIO_IOCTRL_VAL
@ -274,7 +355,7 @@ proc setupUART0 {} {
proc putcUART0 {char} {
set UART0_LSR [regs UART0_LSR]
set UART0_LSR [regs UART0_LSR]
set UART0_THR [regs UART0_THR]
set LSR_TEMT [regs LSR_TEMT]
@ -308,17 +389,24 @@ proc trainDDR2 {} {
resume
}
proc flashUBOOT {} {
proc flashUBOOT {file} {
# this will update uboot on NOR partition
set EXP_CS0_BASEADDR [regs EXP_CS0_BASEADDR]
# setup CS0 controller for NOR
setupNOR
# make sure we are accessing the lower part of NOR
lowGPIO5
flash probe 0
puts "Erasing sectors 0-3 for uboot"
putsUART0 "Erasing sectors 0-3 for uboot\n"
flash erase_sector 0 0 3
puts "Programming u-boot, takes about 4-5 min for 256kb"
flash write_image ./images/u-boot.bin $EXP_CS0_BASEADDR
puts "Programming u-boot"
putsUART0 "Programming u-boot..."
memwrite burst enable
flash write_image $file $EXP_CS0_BASEADDR
memwrite burst disable
putsUART0 "done.\n"
putsUART0 "Rebooting, please wait!\n"
reboot
}

View File

@ -1,9 +1,60 @@
source [find c100.cfg]
# basic register defintion for C100
source [find c100regs.tcl]
# board-config info
source [find c100config.tcl]
# C100 helper functions
source [find c100helper.tcl]
# Telo board & C100 support trst and srst
# Note that libftd2xx.so tries to assert srst
# which break this script
# use libftdi.so library instead with this script
# make the reset asserted to
# allow RC circuit to discharge for: [ms]
jtag_nsrst_assert_width 100
jtag_ntrst_assert_width 100
# don't talk to JTAG after reset for: [ms]
jtag_nsrst_delay 100
jtag_ntrst_delay 100
reset_config trst_and_srst separate
# issue telnet: reset init
# issue gdb: monitor reset init
$_TARGETNAME configure -event reset-init {
jtag_khz 100
# this will setup Telo board
setupTelo
#turn up the JTAG speed
jtag_khz 3000
puts "JTAG speek now 3MHz"
puts "type helpC100 to get help on C100"
}
$_TARGETNAME configure -event reset-deassert-post {
# Force target into ARM state.
# soft_reset_halt # not implemented on ARM11
puts "Detected SRSRT asserted on C100.CPU"
}
$_TARGETNAME configure -event reset-assert-post {
puts "Assering reset"
#sleep 10
}
proc power_restore {} { puts "Sensed power restore. No action." }
proc srst_deasserted {} { puts "Sensed nSRST deasserted. No action." }
# boots from NOR on CS0: 8 MBytes CFI flash, 16-bit bus
# it's really 16MB but the upper 8mb is controller via gpio?
# it's really 16MB but the upper 8mb is controller via gpio
# openocd does not support 'complex reads/writes' to NOR
flash bank cfi 0x20000000 0x01000000 2 2 $_TARGETNAME
#
gdb_memory_map enable
# writing data to memory does not work without this
memwrite burst disable