imi415
/
openocd
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

doc/openocd.texi: Add documentation for bcm2835 interface 

This adds documentation for the bcm2835 interface configuration
parameters to the user manual. Documentation format is based on
the FTDI interface section, and was taken from the descriptions
in the driver source code.

Change-Id: I77b09b8bd44d8e8fe9cc5fb9de3c3a30550d943c
Signed-off-by: Matthew Mets <matt@blinkinlabs.com>
Reviewed-on: http://openocd.zylin.com/6376
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commit is contained in:
Matthew Mets 2021-07-22 01:25:15 +02:00 committed by Antonio Borneo
parent dbb10a57d1
commit d94e1ffef0
1 changed files with 67 additions and 0 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

67
doc/openocd.texi
View File

@ -3197,6 +3197,73 @@ configuration on exit.
See @file{interface/raspberrypi-native.cfg} for a sample config and
pinout.
@deffn {Config Command} {bcm2835gpio_jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
Set JTAG transport GPIO numbers for TCK, TMS, TDI, and TDO (in that order).
Must be specified to enable JTAG transport. These pins can also be specified
individually.
@end deffn
@deffn {Config Command} {bcm2835gpio_tck_num} @var{tck}
Set TCK GPIO number. Must be specified to enable JTAG transport. Can also be
specified using the configuration command bcm2835gpio_jtag_nums.
@end deffn
@deffn {Config Command} {bcm2835gpio_tms_num} @var{tms}
Set TMS GPIO number. Must be specified to enable JTAG transport. Can also be
specified using the configuration command bcm2835gpio_jtag_nums.
@end deffn
@deffn {Config Command} {bcm2835gpio_tdo_num} @var{tdo}
Set TDO GPIO number. Must be specified to enable JTAG transport. Can also be
specified using the configuration command bcm2835gpio_jtag_nums.
@end deffn
@deffn {Config Command} {bcm2835gpio_tdi_num} @var{tdi}
Set TDI GPIO number. Must be specified to enable JTAG transport. Can also be
specified using the configuration command bcm2835gpio_jtag_nums.
@end deffn
@deffn {Config Command} {bcm2835gpio_swd_nums} @var{swclk} @var{swdio}
Set SWD transport GPIO numbers for SWCLK and SWDIO (in that order). Must be
specified to enable SWD transport. These pins can also be specified individually.
@end deffn
@deffn {Config Command} {bcm2835gpio_swclk_num} @var{swclk}
Set SWCLK GPIO number. Must be specified to enable SWD transport. Can also be
specified using the configuration command bcm2835gpio_swd_nums.
@end deffn
@deffn {Config Command} {bcm2835gpio_swdio_num} @var{swdio}
Set SWDIO GPIO number. Must be specified to enable SWD transport. Can also be
specified using the configuration command bcm2835gpio_swd_nums.
@end deffn
@deffn {Config Command} {bcm2835gpio_swdio_dir_num} @var{swdio} @var{dir}
Set SWDIO direction control pin GPIO number. If specified, this pin can be used
to control the direction of an external buffer on the SWDIO pin (set=output
mode, clear=input mode). If not specified, this feature is disabled.
@end deffn
@deffn {Config Command} {bcm2835gpio_srst_num} @var{srst}
Set SRST GPIO number. Must be specified to enable SRST.
@end deffn
@deffn {Config Command} {bcm2835gpio_trst_num} @var{trst}
Set TRST GPIO number. Must be specified to enable TRST.
@end deffn
@deffn {Config Command} {bcm2835gpio_speed_coeffs} @var{speed_coeff} @var{speed_offset}
Set SPEED_COEFF and SPEED_OFFSET for delay calculations. If unspecified,
speed_coeff defaults to 113714, and speed_offset defaults to 28.
@end deffn
@deffn {Config Command} {bcm2835gpio_peripheral_base} @var{base}
Set the peripheral base register address to access GPIOs. For the RPi1, use
0x20000000. For RPi2 and RPi3, use 0x3F000000. For RPi4, use 0xFE000000. A full
list can be found in the
@uref{https://www.raspberrypi.org/documentation/hardware/raspberrypi/peripheral_addresses.md, official guide}.
@end deffn
@end deffn
@deffn {Interface Driver} {imx_gpio}