Fw: [PATCH] OpenRD board configuration
Ofrwarded from Ron, who's not subscribed. ----- Forwarded message from Ron <ron@debian.org> ----- From: Ron <ron@debian.org> Date: Wed, 14 Oct 2009 04:50:17 +1030 To: wookey@debian.org Subject: [PATCH] OpenRD board configuration X-Spam-Status: No, score=-3.6 required=4.5 tests=BAYES_00,RCVD_IN_DNSWL_LOW autolearn=ham version=3.2.5 This piggybacks on the 'sheevaplug' layout which uses the same Kirkwood SoC. Signed-off-by: Ron Lee <ron@debian.org>
This commit is contained in:
Wookey
Øyvind Harboe
parent
a894c2d8b2
commit
dd54981702
|
|
@ -0,0 +1,122 @@
|
|||
# Marvell OpenRD
|
||||
|
||||
source [find interface/openrd.cfg]
|
||||
source [find target/feroceon.cfg]
|
||||
|
||||
$_TARGETNAME configure \
|
||||
-work-area-phys 0x10000000 \
|
||||
-work-area-size 65536 \
|
||||
-work-area-backup 0
|
||||
|
||||
arm7_9 dcc_downloads enable
|
||||
|
||||
# this assumes the hardware default peripherals location before u-Boot moves it
|
||||
nand device orion 0 0xd8000000
|
||||
|
||||
proc openrd_init { } {
|
||||
|
||||
# We need to assert DBGRQ while holding nSRST down.
|
||||
# However DBGACK will be set only when nSRST is released.
|
||||
# Furthermore, the JTAG interface doesn't respond at all when
|
||||
# the CPU is in the WFI (wait for interrupts) state, so it is
|
||||
# possible that initial tap examination failed. So let's
|
||||
# re-examine the target again here when nSRST is asserted which
|
||||
# should then succeed.
|
||||
jtag_reset 0 1
|
||||
feroceon.cpu arp_examine
|
||||
halt 0
|
||||
jtag_reset 0 0
|
||||
wait_halt
|
||||
|
||||
arm926ejs cp15 0 0 1 0 0x00052078
|
||||
|
||||
mww 0xD0001400 0x43000C30 # DDR SDRAM Configuration Register
|
||||
mww 0xD0001404 0x37543000 # Dunit Control Low Register
|
||||
mww 0xD0001408 0x22125451 # DDR SDRAM Timing (Low) Register
|
||||
mww 0xD000140C 0x00000A33 # DDR SDRAM Timing (High) Register
|
||||
mww 0xD0001410 0x000000CC # DDR SDRAM Address Control Register
|
||||
mww 0xD0001414 0x00000000 # DDR SDRAM Open Pages Control Register
|
||||
mww 0xD0001418 0x00000000 # DDR SDRAM Operation Register
|
||||
mww 0xD000141C 0x00000C52 # DDR SDRAM Mode Register
|
||||
mww 0xD0001420 0x00000004 # DDR SDRAM Extended Mode Register
|
||||
mww 0xD0001424 0x0000F17F # Dunit Control High Register
|
||||
mww 0xD0001428 0x00085520 # Dunit Control High Register
|
||||
mww 0xD000147c 0x00008552 # Dunit Control High Register
|
||||
mww 0xD0001504 0x0FFFFFF1 # CS0n Size Register
|
||||
mww 0xD0001508 0x10000000 # CS1n Base Register
|
||||
mww 0xD000150C 0x0FFFFFF5 # CS1n Size Register
|
||||
mww 0xD0001514 0x00000000 # CS2n Size Register
|
||||
mww 0xD000151C 0x00000000 # CS3n Size Register
|
||||
mww 0xD0001494 0x00120012 # DDR2 SDRAM ODT Control (Low) Register
|
||||
mww 0xD0001498 0x00000000 # DDR2 SDRAM ODT Control (High) REgister
|
||||
mww 0xD000149C 0x0000E40F # DDR2 Dunit ODT Control Register
|
||||
mww 0xD0001480 0x00000001 # DDR SDRAM Initialization Control Register
|
||||
mww 0xD0020204 0x00000000 # Main IRQ Interrupt Mask Register
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
mww 0xD0020204 0x00000000 # "
|
||||
|
||||
mww 0xD0010000 0x01111111 # MPP 0 to 7
|
||||
mww 0xD0010004 0x11113322 # MPP 8 to 15
|
||||
mww 0xD0010008 0x00001111 # MPP 16 to 23
|
||||
|
||||
mww 0xD0010418 0x003E07CF # NAND Read Parameters REgister
|
||||
mww 0xD001041C 0x000F0F0F # NAND Write Parameters Register
|
||||
mww 0xD0010470 0x01C7D943 # NAND Flash Control Register
|
||||
|
||||
}
|
||||
|
||||
proc openrd_reflash_uboot { } {
|
||||
|
||||
# reflash the u-Boot binary and reboot into it
|
||||
openrd_init
|
||||
nand probe 0
|
||||
nand erase 0 0x0 0xa0000
|
||||
nand write 0 uboot.bin 0 oob_softecc_kw
|
||||
resume
|
||||
|
||||
}
|
||||
|
||||
proc openrd_load_uboot { } {
|
||||
|
||||
# load u-Boot into RAM and execute it
|
||||
openrd_init
|
||||
load_image uboot.elf
|
||||
verify_image uboot.elf
|
||||
resume 0x00600000
|
||||
|
||||
}
|
||||
|
||||
|
|
@ -0,0 +1,12 @@
|
|||
#
|
||||
# Marvell OpenRD
|
||||
#
|
||||
# http://www.marvell.com/products/embedded_processors/developer/kirkwood/openrd.jsp
|
||||
#
|
||||
|
||||
interface ft2232
|
||||
ft2232_layout sheevaplug
|
||||
ft2232_vid_pid 0x0403 0x9e90
|
||||
ft2232_device_desc "OpenRD JTAGKey FT2232D B"
|
||||
jtag_khz 3000
|
||||
|
||||
Loading…
Reference in New Issue