We changed the actual target name quite a while ago.
This changes the actual target function names/defines to also match
this change.
Change-Id: I4f22fb107636db2279865b45350c9c776e608a75
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1626
Tested-by: jenkins
Enable reading the SWO trace output via STLinkv2 dongles that support
it.
This adds an optional initialization parameter "trace" with which the user
specifies a destination file where SWO trace output is appended as it comes in
as well as the trace module's source clock rate.
STLink will be configured for a 2MHz SWO data rate (STLink's highest
supported rate) if the source clock is > 2MHz, otherwise the source
clock is used as the data rate directly.
For example:
trace swo.log 168000000
If "trace" is specified with a usable file path, the stlink_usb driver will
attempt to configure and read SWO trace data as follows:
- on _run(), the target's TPI and TMI are configured and the STLinkv2 is told
to enable tracing. Only generic ARM TPI and TMI registers are
configured, any MCU-specific settings (ex: pin routing) are the
responsibility of the target firmware. The configuration applied is
based on the STLinkv2's capabilities (UART emulation).
- on _v2_get_status(), the trace data (if any) is fetched from the
STLink after the target status is checked and the target is found to
be running.
- on _halt(), the STLink is told to disable tracing.
When fetching trace data, the entire trace frame is written to the output file
and that data is flushed. An external tool may be used to parse the
trace data into a more human-readable format.
Tested on ARM Cortex M4F and M3 MCUs (STM32F407 and STM32L152).
Change-Id: Ic3983d46c82ba77010c23b0e18ce7b275d917f12
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1524
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Watchpoints were not being enabled when the hl adapter target was resumed.
This effects both stlink and icdi interfaces.
Change-Id: Ia9f8a9415be97a467cd099b63b6bc9f7f37d0c0d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/931
Tested-by: jenkins
The stacking of ChibiOS/RT depends on the usage of an FPU. If the
FPU is enabled the FPU registers are also saved on context switch.
This patch adds automatic detection of FPU for armv7m targets.
Note: With this patch, openocd will only output an error message
warning that the FPU is enabled.
For further FPU support, the correct stacking information
also needs to be added.
Change-Id: I0984cbd9180f247ba2fa610e74a6413cc54239ea
Signed-off-by: Matthias Blaicher <matthias@blaicher.com>
Reviewed-on: http://openocd.zylin.com/961
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch determine all cpu types and not only
the cortex M3 and the stm32 target use the common
target examine function from the cortex_m sources.
Change-Id: If689dd994b3855284b927fc4b206f420cf32b6c7
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/511
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Change this functions to make it accessible for other
target implementations.
Change-Id: Ib41fc793cfb4de5439af026c2e8b52e7a9507c85
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/278
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This rename is in preparation for cortex_m4 support.
Change-Id: Ic08c298ec6ed2aabc2c39db67191f68b3a51f550
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/147
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Spencer Oliver
Andrey Yurovsky
Matthias Blaicher
Mathias K