Believe in using defines to make maintenance easier.
Change-Id: I8edf151352131bbf2b884dfcd67ca5764b11b13c
Signed-off-by: Kent Brinkley <jkbrinkley.imgtec@gmail.com>
Reviewed-on: http://openocd.zylin.com/2350
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Added new chip id based flash size.
Change-Id: I5b5e71074af0e50352443f66f88adfc6e14280bf
Signed-off-by: Peter Kuhar <peter@pkuhar.com>
Reviewed-on: http://openocd.zylin.com/3732
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
arm-none-eabi target triplet defaults to Little Endian, and so far any
submitted machine code snippets have been verified to be Little Endian.
However a user might override [ARM_]CROSS_COMPILE with an armeb toolchain,
potentially resulting in invalid machine code.
Let's be safe and enforce Little Endian mode for assembler and compiler.
Change-Id: I9cefe24689eaded25d60ffb1f254b254e8d76f9d
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3498
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Kinetis family employs strange concept of Flash Configuration Field at
address 0x400 of program flash. Writing incorrect data to FCF may
permanently lock the device.
The change introduces 'kinetis fcf_source protection' mode. In this mode
write of flash image data to FCF is prevented. FCF data build from
protection (set by 'flash protect' command) are written instead.
FCF data are written also just after erase of relevant sector. It
protects device from locking security by reset or power cycle after erase.
prot_blocks array is used as protection blocks have bigger size than sectors.
Alignment and padding programming sections is rewritten to fix
writing with not section boundary aligned begin.
Change-Id: I9fc8bd37d6f627fb8ed7abb7f7560e78a740b195
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3562
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Add kinetis_ftfx_decode_error() to show flash error type in human
readable message.
Add kinetis_ftfx_prepare() to prepare flash module just once in
command (not each time kinetis_ftfx_command() is called).
Change target_read/write_memory() to target_read/write_u8/32().
Make ftfx_fstat parameter of kinetis_ftfx_command() optional.
Longword flash write:
Fix huge memory leak after write of unaligned block.
Check flash address alignment properly.
Do not fill whole padding buffer but its end after original data.
Remove duplicite padding.
Change-Id: Ia5e312909f68d3cc724c8cbffe1cd903b9102124
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3561
Tested-by: jenkins
Reviewed-by: Steven Stallion <stallion@squareup.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Originally flash/nor infrastructure assumed protection blocks identical
to erase sectors. This assumption is not valid for many flash types.
Driver code fixed the problem either by increasing sector size to
size of protection block or by defining more protection block than
really existed in device. Both cases had drawbacks.
The change retains compatibility with the old driver.
Updated driver can set protection blocks table independent
of sector table.
Change-Id: I27f6d267528ad9ed9fe0a85f05436a8ec17603a4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3545
Tested-by: jenkins
Reviewed-by: Steven Stallion <stallion@squareup.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The change prevents starting mass_erase in unstable state of MCU
(RESET/WDOG loop).
mass_erase of secured MCU using manual reset button is supported.
Timeouts are measured by timeval_ms() instead of iteration count.
mass_erase timeout prolonged to 16 seconds because aborting
mass_erase in progress (deasserting reset) leaves the device
in security locked state.
Change-Id: I6605532df56080a54c2a1dfe49094e3db4ce534a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3551
Tested-by: jenkins
Reviewed-by: Steven Stallion <stallion@squareup.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Kinetis driver checks MDM STAT register to detect secured state of MCU.
Original version often reported a blank device as secured one.
Change #3010 has not fixed all false reports.
After changes in arm_adi_v5 infrastructure secured devices was not detected
at all.
New algorithm uses multiple MDM STAT reads and counts MDM_STAT_SYSSEC and
MDM_STAT_FREADY bits. Both secured MCU and MCU locked-up in RESET/WDOG loop
are detected reliably.
Detection is run in both kx.cfg and klx.cfg from examine-start event,
not examine-end as before. Event is configured only for non hla adapter.
Minor fix in klx.cfg: commented out adapter_khz 24000 in reset-init.
Such frequency is not supported in VLPR CPU mode and with JTAG.
Change-Id: I2ec2b68c45bde9898159cd15fbdcbcfa538c41d9
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3547
Tested-by: jenkins
Reviewed-by: Steven Stallion <stallion@squareup.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
NXP (nee Freescale) documents the mass erase procedure using the MDM-AP
block in AN4835. Existing support for this feature did not properly
handle boards without SRST. This patch updates the mass_erase command
such that it works correctly on these boards. Additionally, the core is
left in a halted state once complete to prevent reset loops due to the
watchdog as reported by some users.
Since the MDM-AP provides an additional method of halting and resetting
the core that is disconnected from the DAP, additional commands are
provided to manage this state. These commands are particularly helpful
when connecting to a target with an unknown state.
Change-Id: I40f006d5d964befb12b019c5d509988decdd3f91
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3540
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
at91sam7_read_part_info() walks throw all flash banks following
current one.
I don't know why it has to do it at all (possibly for multi-bank
devices like SAM7S512), but if there is more than one target in JTAG
chain, this lookup can touch flash bank of another (possibly not
halted) target, which cause probe error and current command
execution abort.
[andreas.fritiofson@gmail.com]: Change to for-loop and reduce
indentation
Change-Id: Ide50e93578786e1250f7a0fd0e3d296247924814
Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/2610
Tested-by: jenkins
This change adds JTAG transport in pass-through mode
to the cmsis-dap driver. The patch is originally from
Phillip Pearson <pp@myelin.co.nz>, with additions
by Maksym Hilliaka <oter@frozen-team.com>
Change-Id: I88d918d6576e9d875c3b611f29f255581e6a5424
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3568
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
XDS100v3 is software compatible with the XDS100v2, but has a
different usb pid. This commit adds `xds100v3.cfg` that sources
the v2 one and changes the usb pid.
Change-Id: Ie29d325e8992d2de2f97d70862beeb63932ffa80
Signed-off-by: Remco Bloemen <openocd-gerrit@xn--2-umb.com>
Reviewed-on: http://openocd.zylin.com/3632
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
MBFTDI is a very cheap FT2232-based JTAG adapter
for programming Marsohod FPGA board.
Please see http://www.marsohod.org/prodmbftdi for details.
Change-Id: I35f758b49d1566098dc27f9581829cccad93ceeb
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-on: http://openocd.zylin.com/3604
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The instructions to set the port to zero to disable a service has not
worked for several years: the effect of doing so is to start the service
on a port randomly selected by the bind(2) system call.
Update the documentation to reflect the new standard way of disabling
network services.
Change-Id: Ic5315a80f9956ea195f63e05d30d604a980bbc8f
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Reviewed-on: http://openocd.zylin.com/3638
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Although the documentation suggested this worked, and it is implemented
for tcl_port and telnet_port, the directive was not recognized for
gdb_port.
Change-Id: I38d95ee879ec3f6d551603b7313749a21e0e498e
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Reviewed-on: http://openocd.zylin.com/3637
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
- added ids for various parts
- rewrite of sector allocation to deal with dual-bank F76x/77x
- single- / dual-bank mode for F76x/77x
- sector protection adapted for F76x/77x in dual-bank mode
- handling of additional option bits (28-31) in FLASH_OPTCR
in options_read and options_write for F42x/43x/469/479/7xx,
options bits 0-1 masked out
- check for sensible value of user_options in options_write
- some #defines clarified, non-needed ones removed
- docs updated (options read, options write)
Change-Id: Ie4db80e60baa7d2663e024ab1f278640b1ce901b
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/3526
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This patch removes the display_str member in the thread_detail struct.
This member was not being used and provides no additional benefit over
the thread_name_str and extra_info_str members. This change is made in
preparation of support for the qXfer:threads:read packet, which will
modernize how thread information is shared with GDB.
Change-Id: I1f8bc6325e6aa790e02ea6caee9d6f44c5fedf36
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3558
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Only report non-erased or unknown sectors or if bank is fully erased.
Change-Id: I94f0bc2a0d6529d1ea5f66b284cefd6a2c61fe39
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/3501
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
1) wrong last bit was shifted out in the end of IRSHIFT/DRSHIFT in
jlink_execute_scan()
2) TDI buffer was not cleared in jlink_tap_init(), results in wrong
data shifted out to the TDI and "Bad value '00000000' captured
during DR or IR scan" error message.
3) sizeof(tdi_buffer) was used in memset() to clean tms buffer. It
is the same as sizeof(tms_buffer), but shoud be fixed to make source
code consistent
Change-Id: I13f26d1c3e88eefc3856fe2b8542fb0ccea6acb1
Signed-off-by: Sergey A. Borshch <sb-sf@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/3394
Tested-by: jenkins
Reviewed-by: Harry Zhurov <harry.zhurov@gmail.com>
Reviewed-by: Anton Gusev
Reviewed-by: Михаил Цивинский <mtsivinsky@gmail.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Increase workareasize when it is know we have a larger device.
Change-Id: Ieaee92e7cd25cc201989f14de122349698871412
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Reviewed-on: http://openocd.zylin.com/3378
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Corrected 2 Silicon IDs that were swapped.
I've tested with a CY8C4125AXI-483 and confirmed
that the device is recognized correctly now.
Change-Id: I6fcbee33558d8feec9abf6052df3f15523379c48
Signed-off-by: George Ioakimedes <georgeioak@gmail.com>
Reviewed-on: http://openocd.zylin.com/3619
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
target_run_flash_async_algorithm() ignored abort from target
(rp set to 0) when raised after all data have been written in fifo.
I could result e.g. in not reported error during flash write.
The change adds rp test after target algorithm has finished.
Change-Id: Iadd93371e4a4602737be10079479285d81ae41b2
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3560
Tested-by: jenkins
Reviewed-by: Steven Stallion <stallion@squareup.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Using the presence of the 'chSysInit' symbol for detection of
ChibiOS is dangerous because this symbol may not be available
if link-time optimisation is used.
This patch removes this reliance, so the symbols 'ch' and 'ch_debug'
are the only things required for ChibiOS detection.
If 'ch' is present but 'ch_debug' is not, an info message suggests
that Chibios might be present without its registry being enabled.
This message has been reworded a little to make it slightly more
equivocal because the chances of a false positive message are
increased.
Addresses bug #121, "ChibiOS rtos detection fails with LTO enabled".
Change-Id: I5ef224735c06446751adee010ce75be4f30f0403
Signed-off-by: Andy Pomfret <cooperised@gmail.com>
Reviewed-on: http://openocd.zylin.com/3381
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Instead of using ARM_ prefixed variables and an "arm" target,
use CROSS_COMPILE, AS, OBJCOPY. This requires to switch from ?= to =
to avoid the host assembler getting invoked.
This allows to handle kinetis_ke subdirectory like fm4 and xmc1xxx.
Change-Id: I7ea0bf119f6c4716f4d6002794004730af49eef4
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3505
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add a Makefile that orchestrates the other loader Makefiles.
It assumes that the clean target can be run without cross toolchain.
at91sam7x does not successfully build and is not really needed either,
therefore left out.
Add an exception to .gitignore for any contrib/loaders Makefile.
Change-Id: I74456b768472f3190a1721bcf41a777bb8daf973
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3504
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
PSoC4 design prevents reset halt/init with standard/low level
SWD adapter if hw reset line configured. Give user hint
to use 'reset_config none' in such case.
Change-Id: I0ca2c46b8575829b0013fd151f2eb63963d66653
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3617
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
- FPU detection and FPU register support added for Cortex-M7.
There is no apparent difference between FPv4 and FPv5_SP but ...
- Autoincrement range for MEM-AP added for Cortex-M7
This patch together with #3526 replaces #3123 except for stm32f7x.cfg.
Change-Id: I5ed5392e3835674160563ff37d67622a7bf2c877
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/3531
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The IDCODE of Artix7 15T in the UG470 is wrong; Artix7 35T and 15T don't have the same IDCODE.
I've tested this on real hardware.
Change-Id: Iac267dc449c23454dd119126749dbeb8267c18ac
Signed-off-by: Felix Held <felix-openocd@felixheld.de>
Reviewed-on: http://openocd.zylin.com/3633
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
If WAIT recovery fails (times out), an ABORT command is issued to the
DAP but under some conditions the SSTICKYORUN bit in CTRL/STAT is not
cleared as well, which renders the DP unusable. This happens when
trying to access e.g. the ROM table of powered-down cores, on many
targets.
Change-Id: Id0a7ba6180069eee562871314f520f938df9718f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3476
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Allow using physical addresses with mem2array and array2mem. In order
to minimize the impact on existing scripts, "phys" is added as an
optional 5th parameter to both commands.
This patch also adds "phys" variants to the memwrite/memread commands
in memory.tcl.
Change-Id: Ia6307f9d861789e7f3ccf1f98961d666bf8d85d6
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3387
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Sometimes it is necessary to resume into a different state (ARM/Thumb)
than at debug state entry. According to the documentation this should
be possible with "arm core_state arm|thumb" before the resume command,
however the original code also restores the original CPSR, which
overrides whatever state the core was set to. This seems to work on some
cores (e.g. Cortex-A5) but not on others (e.g. Cortex-A9). Using the "BX"
instruction to set resume PC and core state works on Cortex-A9 and
ARM11, but is not sufficient on Cortex-A5, where an explicit write to
the PC (MOV pc, r0) is required additionally.
Change-Id: Ic03153b4b250fbb8cf6c75f8e329fb34829aa35f
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3386
Tested-by: jenkins
Reviewed-by: Alexander Stein <alexanders83@web.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
1986VE1T and 1986VE3T have issue with flash acceleration engine described
in their errata (issue 0007).
After programming flash acceleration engine's buffer contains old data,
and therefore first read data are wrong. Because of this verification after
programming fails always. Recommended workaround for the issue is to flush
flash accelerator's buffer. To do so it's necessary to read at least 64
bytes of flash through accelerator.
Reading bytes through JTAG using default_flash_read doesn't help.
It seems that reading should be done by uC itself.
Change-Id: I18ef464a68ad5c5b16d3933f31ca61f8e2e7cca3
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-on: http://openocd.zylin.com/3509
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
First, fix the timeval_ms() implementation to not have K&R but ANSI
argument semantics by adding a missing void.
timeval_ms() returns an int64_t, not uint64_t or long long. Consistently
use int64_t for variables and PRI*64 as format string.
While at it, change a few related variables to bool for clarity.
Note that timeval_ms() may return a negative error code, but not a
single caller checks for that.
Change-Id: I27cf83e75b3e9a8913f6c43e98a281bea77aac13
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-on: http://openocd.zylin.com/3499
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
A developer tool: Direct access to AP registers can be useful
for handling vendor specific AP like Freescale Kinetis MDM or Atmel SMAP.
Change-Id: Ie2c7160fc6b2e398513eb23e1e52cbb52b88d9bd
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/2777
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
add "mrb" command to read a byte of memory into a variable
Change-Id: I5ddc9fbcc55958a249548627bd15824df6dc0d61
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3542
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Some installations of OpenOCD are used in restricted environments that
do not permit binding to public interfaces.
This patch does not affect the default behavior to listen on all
interfaces, however it does give the option to restrict services by way
of the bindto command.
Change-Id: Id51bd64b376a8c62dd47b08b4d834872925e6af2
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3534
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Andreas Färber
Kent Brinkley
Peter Kuhar
Spencer Oliver
Tomas Vanek
SASANO Takayoshi
Steven Stallion
Andreas Fritiofson
Stephen Tridgell
Matthias Welwarsky
Antony Pavlov
Remco Bloemen
Peter A. Bigot
Andreas Bolsch
Uwe Bonnes
Sergey A. Borshch
George Ioakimedes
Olaf Lüke
Andy Pomfret
Felix Held
Andrey Skvortsov