The target mem_ap misses the method 'deinit_target' and does not
free the memory allocated during 'target create' and 'configure'.
Add the missing method and free the allocated memory.
Issue identified with valgrind.
Change-Id: If0d0114a75dd76a8b65c2d46d96c6085fd31a09d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5700
Tested-by: jenkins
When jtag_libusb_open() fails to find the adapter, it returns
error but left libusb initialized causing memory leak of libusb
internal data.
Issue found with valgrind when no adapter or board is connected to
the host, e.g.
valgrind openocd -f board/st_nucleo_f4.cfg
Close the libusb operations if jtag_libusb_open() has to return
error.
Change-Id: Ieb2f110be15705dafe80c099e7d83c07056c2a41
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5701
Tested-by: jenkins
Current code for Cortex M does not set C_DEBUGEN as soon as
possible, (which means during target examine), but later-on either:
1) at command 'halt' (e.g. for 'gdb-attach' event);
2) at command 'soft_reset_halt';
3) at commands 'reset', 'reset halt' or 'reset init';
4) during polling, but only if the target:
= enter in 'double fault', or
= exit from a reset, or
= halts (not possible if C_DEBUGEN is not set)
Plus, if commands in 1) or 2) are executed before the very first
poll of the target, the value of 'cortex_m->dcb_dhcsr' is used not
initialized while writing it back in DCB_DHCSR.
Another side effect of this situation is that it's possible to set
a HW breakpoint with the target running, while C_DEBUGEN is not
set. Accordingly to [1], C1.3.1 "Debug authentication":
When DGBEN is LOW and DHCSR.S_HALT == 0:
...
FPB breakpoints do not generate an entry to Debug state and,
if no DebugMonitor exception is generated, will escalate to
HardFault, Lockup, or be ignored.
On STM32MP15x I get HW breakpoint ignored, while on STM32F411 I
get HardFault.
E.g. following these steps:
- power-on a pre-flashed board that starts running the firmware;
- connect openocd, without halting or resetting the board;
- set a HW breakpoint to some address often executed;
- wait, but the board doesn't halt ...;
- type the command 'halt';
- if the Cortex-M has HardFault it would be visible and the fault
is at the breakpoint address;
- if no HardFault then type the command 'resume';
- wait and the board will finally halt at the HW breakpoint.
A similar issue has been detected on Cortex-A code and fixed by
commit bff87a7f28 ("target/cortex_a: enable DSCR_HALT_DBG_MODE
during examine").
Follow the same approach and set C_DEBUGEN during examine.
Also, initialize 'cortex_m->dcb_dhcsr' during examine.
[1] ARM DDI 0403E "ARM v7-M Architecture Reference Manual"
Change-Id: I5b0b23403634f7dfce38f104bba9f59c33eb3e99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5702
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Moritz Fischer <moritzf@google.com>
The kept_alive() function is called to inform the keep-alive code
that a keep-alive as been just kicked through some other path.
But kept_alive() erroneously resets the timeout counter without
checking if it has already expired, thus masking a potential
timeout.
Check if timeout counter has expired during kept_alive().
While there, put the timeout values in macros and explicit the
units in the timeout messages.
Change-Id: Iaf6368b44e5b5352b1cc4e7efbb2368575dcfa08
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5705
Reviewed-by: <jonatan_zeidler@gmx.de>
Tested-by: jenkins
Flashing Kinetis MCU MK22FX512VLH12 takes longer than one second,
thus gdb connection can timeout. Before commit 7f260f5009
("helper/command: Handle Tcl return values consistently") the
openocd timeout warning was masked by a bug in gdb_put_packet()
that resets the timeout counter if any message is logged out.
The commit above removes one log message and the timeout warning
is now triggered.
While the bug in gdb_put_packet() is still to be fixed, the reason
of the timeout is the lack of keep_alive() calls in kinetis flash
driver.
Add keep_alive() call at every iteration in function
kinetis_write_sections(), that is reported as core write function
in chunks of 1024 bytes in the log from the reporter.
Add also a keep_alive() call at every iteration in function
kinetis_write_inner(). This part is not present in the log but, by
code analysis, it represents another critical loop.
Change-Id: I38e631b36c7eb2f1e21cef68710ce47c03d3edda
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Jonatan Hatakeyama Zeidler <jonatan.zeidler@medineering.de>
Reviewed-on: http://openocd.zylin.com/5703
Tested-by: jenkins
Reviewed-by: <jonatan_zeidler@gmx.de>
use handle_command_parse_bool within dap_ti_be_32_quirks_command to make
it shorter and simpler.
Change-Id: Ice179cc477933b27e27235dc2ade23fe655e233d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5708
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
avoid the usage of ERROR_COMMAND_SYNTAX_ERROR when
ERROR_COMMAND_ARGUMENT_INVALID is more adequate.
Change-Id: Ic9aaedb93fedd45efee1b39f8ea20185f01af2da
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5654
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
For jtag/drivers/bcm2835gpio dev_mem_fd has been updated within
bcm2835gpio_init with the add on of gpio to mem. This permits the
access to memory of GPIO without the need for root access.
For failed attempt, a fallback to original memory follows.
It should be noted that any printed error is relative to original
memory ("dev/mem").
Tested on EFM32GG12B390F board
Change-Id: I4540bdf62fb3b91a51221e277881adfae138dcc5
Signed-off-by: tscn92 <tscn@kamstrup.com>
Reviewed-on: http://openocd.zylin.com/5568
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new filename has a proper vendor prefix. Keep the old
configuration file for now but show a "deprecated" warning
at runtime.
Change-Id: If7465a752f47f3292e430c8b311148badfd384cd
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5478
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new filename has a proper vendor prefix. Keep the old
configuration file for now but show a "deprecated" warning
at runtime.
Change-Id: I13871ec13709055843e23b1b6da90694fd60505e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5477
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The new filename has a proper vendor prefix. Keep the old
configuration file for now but show a "deprecated" warning
at runtime.
Change-Id: I30fcb8f291d401acaa1fe665db0eeabc250d24b6
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5476
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
While I'm hoping to maintain the chain of redirects for the foreseeable
future, it makes sense to point at the final URL now that Autotools
Mythuster has had its domain for a long while.
Change-Id: I6d912e3be0f81b25bec14746ebfee58f29f144b6
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.com>
Reviewed-on: http://openocd.zylin.com/5709
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The function command_find_in_parent() is never used in OpenOCD, so
remove it.
The functions command_name() and [un]register_command() are only
used internally in command.c, so make them static.
Change-Id: Ide9842659796f4884fb6c1fcf5979b3b71b67abb
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5663
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The jim library exports all the data types through typedef, so
there is no need to use the internal struct types.
Fix the few remaining inconsistencies in the code.
Change-Id: Id4ae0083563ea7a371833374e7b39f17158f66a4
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5662
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Either Jim_CreateCommand() and register_command_handler() return
the jim error code JIM_OK/JIM_ERR.
Fix the check and the initialization of retval.
Change-Id: I3073c66764670128706ad979a43bb3edbbeb0ab0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5661
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
After commit 0840414f0e ("helper/command: do not replace new
commands with ocd_ prefix"), the command name is present in
argv[0], so there is no need to pass it directly. The current code
causes the command name to be logged twice, once explicitly and
then from the content of argv[0]:
openocd -c 'debug_level 3; echo hello; shutdown'
<snip>
Debug: 13 3 command.c:142 script_debug(): command - echo echo hello
<snip>
Debug: 16 4 command.c:142 script_debug(): command - shutdown shutdown
Remove the command name from the arguments of the function
script_debug().
Change-Id: I57860774f450ff717ee71ef9dc07590549a84319
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5660
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The new stlink firmware requires opening the AP before issuing
any operation.
In the current code we have a 'questionable' check about the core
model to set the TAR autoincrement, that is issued without opening
the AP, thus causing a STLINK_BAD_AP_ERROR.
Modify the AP open API to handle this case and open AP#0 before
the memory access to check the core model.
Change-Id: I576955b5094bd41d63ff1fbad7b4fd9433253321
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/5691
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Firmware v2j28 introduces the API to open and close the AP, but
closing AP always returns error 0x1d (STLINK_BAD_AP_ERROR).
Ignore the error returned by the bogus firmware on closing AP.
Change-Id: I992ddbf7acb10f1d376ed8f781eeb3344605b85d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5683
Tested-by: jenkins
When the transport is not specified, OpenOCD uses the first listed
by the selected adapter driver.
The old HLA driver for stlink lists SWD as first. The new driver
dapdirect instead lists JTAG, making more difficult a fallback to
HLA when dapdirect is not available due to old stlink FW.
Plus, in case of JTAG wiring, SWD is still possible, while the
opposite is not.
Reorder the list of transports to grant the default to SWD.
Change-Id: Id9c529e921b148d5b352d4603a9028c2a5f15d83
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Suggested-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5538
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Previously the adapter speed settings were hard-coded to
connect with low speed then switch over to high speed
regardless what was mentioned in the cfg files. Now the
stm8 target intercept adapter speed settings and configure
the stm8 control registers accordingly.
Change-Id: I7419514e5214e4b43b9d51253cf5b7f04a233533
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/5548
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The transport SWIM is selected twice, in board and in target, thus
a warning is generated at run-time. It should be fixed by remove a
line in the target file, but does not harm so let's keep it there
for the time being.
Change-Id: I479004dc16005a330d552c8dbd5def61690f9b9f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5543
Tested-by: jenkins
No reason to keep longer this temporary hack.
Remove it by reverting the original commit.
Change-Id: I5c6dcdb1f4755b7dba4c03a5033913ef8db35e18
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5533
Tested-by: jenkins
Now that SWIM is not accessed through HLA anymore, decouple the
SWIM code and remove the conditional execution.
Fix the inconsistency of the return type for stlink_usb_state() in
case of SWIM (returns ERROR_OK while type is enum target_state)
introduced by commit 3de6b5f6e5 ("jtag/drivers/stlink_usb :
implemented and repaired SWIM support").
The code added by commit above in stlink_usb_state() is an hack to
reuse existing HLA API to perform a reconnect.
Move the SWIM specific code from stlink_usb_state() to a dedicated
stlink_swim_op_reconnect() that provides consistent data type.
Change-Id: I3fe175fef00b0735bea6139b057f217a080c9d38
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 3de6b5f6e5 ("jtag/drivers/stlink_usb : implemented and repaired SWIM support")
Reviewed-on: http://openocd.zylin.com/5532
Tested-by: jenkins
Thanks to API separation between SWIM and the other transports, we
can easily split the memory read/write for SWIM from the rest of
the code.
While there, use the macro STLINK_DATA_SIZE as size of data chunks
that can be read/write in SWIM. This was not implemented before.
Change-Id: I7d913c92539007e4d914480bacc0126a8f0e9705
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5531
Tested-by: jenkins
Add SWIM and STM8 to documentation and update TODO file.
Introduce transport "swim" and command "swim newtap".
Switch in swim.c from HLA API to the new SWIM API.
Implement in stlink driver the SWIM APIs as wrappers of existing
HLA functions.
Remove any SWIM related reference from HLA files.
Update stm8 config files and stlink-dap interface config file.
Change-Id: I2bb9f58d52900f6eb4df05f979f7ef11fd439c24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5530
Tested-by: jenkins
SWIM transport only supports two adapter speeds:
- "low speed" equal to 363 kHz (8 MHz / 22)
- "high speed" equal to 800 kHz (8 MHz / 10)
Replace the previous convention that use "0" or "1" for "low" or
"high" speed with the effective speed in kHz.
Rework the implementation of stlink_speed_swim().
Set low speed in the stm8 config files, because only low speed is
permitted at debug connection; the previous code ignores the
initial value.
Change-Id: I2484c9419a2c554c59eb6b9216339393ab0b54f3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5529
Tested-by: jenkins
SWIM is implemented by (ab)using the HLA API. This was acceptable
when OpenOCD code did not provided a clear separation between
transports and related APIs. Still today SWIM in OpenOCD is only
supported by STLink, so the decision to re-use the HLA API was the
simpler way to implement it.
After commit efd1d64222 ("adapter: switch from struct
jtag_interface to adapter_driver") the transports API are better
split and SWIM can be implemented as a separate set of API. This
would open the possibility to extend OpenOCD for other adapters
that provide SWIM, e.g. versaloon, or through SPI emulation [1].
Introduce a new set of files swim.[ch] to handle the SWIM API.
Beside the API that almost match the transport low-level data
communication (system_reset, read_mem, write_mem), add a further
API reconnect. Today, inside HLA STLink code, the reconnect is
implemented by hacking the HLA API state(). Please notice that
due to this hack the return type is incorrect; stlink_usb_state()
returns ERROR_OK in SWIM mode, while its return type is enum
target_state. Ignore the type mismatch and still call the HLA API
state in the new SWIM API reconnect. Further commit will fix it.
[1] http://kuku.eu.org/?projects/stm8spi/stm8spi
Change-Id: I52018e1e2200cbd41af8e5031f7b35dc761b61d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5528
Tested-by: jenkins
The transition of STM8/SWIM out of HLA will require a new struct
swim_ops in struct adapter_driver.
To simplify the development, make the HLA interface temporarily
accessible through the struct adapter_driver.
This commit will be reverted after the swim rework.
Change-Id: I1e4f370cf64641164d7bcaa22f75ac58c9240052
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5527
Tested-by: jenkins
In the driver's code it's widely used the enum hl_transports for
any check concerning the current transport, even for the non-hla
transport dapdirect.
The driver already provides a stlink specific enum stlink_mode
that can be used in place of the hla one.
Replace the hla enum with the stlink one allover the code.
Introduce a hla specific wrapper stlink_usb_hl_open() to cope with
the only API that requires the hla specific enum.
The overall behaviour is not changed, with exception for a debug
message in stlink_usb_open() than now prints the numeric value of
stlink enum in place of the numeric value of the corresponding hla
one.
This change prepares the road for moving SWIM transport out of hla
by removing any reference to the macro HL_TRANSPORT_SWIM from the
stlink driver.
Change-Id: Ieeea34f312245a94bfc1333087afdb8eb9f77139
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5526
Tested-by: jenkins
This is a follow-up to 3c9bd7c6f3.
Change-Id: If430f7fcfbba084d9cd74b32344ad43508a96a77
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4383
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit da41bce3ae ("target/arc: introduce breakpoint
functionality") introduces a mismatch between the format string
and one int constant.
Change the format string to match the int constant.
Change-Id: I0d59552205551b90e165c0a2e3fef247ad0c7701
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: da41bce3ae ("target/arc: introduce breakpoint functionality")
Reviewed-on: http://openocd.zylin.com/5655
Tested-by: jenkins
Reviewed-by: Evgeniy Didin <didin@synopsys.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Expression like (0xffff << 16) evaluate to type int, which is not able
to hold that value, producing a warning when compiling with
-fsanitize=undefined. This patch makes most of the cortex_m constants
unsigned using the BIT() macro or appending "ul" when possible to fix
the undefined behavior warning.
Signed-off-by: iosabi <iosabi@protonmail.com>
Change-Id: I7af194305ef612d7a32e74eaf9f11dd85fa87f32
Reviewed-on: http://openocd.zylin.com/5583
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types OPEN_BRACE -f {} \;
Change-Id: I6d1356ed11e2699525f384efb7556bc2efdc299f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5628
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
The coding style is quite permissive allowing 120 chars per line,
but abuses are still present.
Fix them, wrapping the lines.
Change-Id: I94d66b651d759a60ec35f7ba115c43933e70ed69
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5626
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The re is no need to split a long string, apart for fitting the
predefined line width.
Join the consecutive string fragments.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types STRING_FRAGMENTS -f {} \;
Change-Id: I8de52d572b0e3d4788c1d4d2b0cf8f94c7f08409
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5625
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The statement "else" should not be on a new line when follows a
close brace '}'. Fix it!
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types ELSE_AFTER_BRACE -f {} \;
Change-Id: I8af247ec3f75a69713d7cb1e73881254d16c189e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5623
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
For void functions, a return as last statement is useless.
Remove it.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types RETURN_VOID -f {} \;
Change-Id: Ie0616fe98623f30d2d7b04ac9517d669774092de
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5622
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Functions that have no parameters should use "void" as parameter
in the function declaration.
Issue identified and fixed by script checkpatch from Linux kernel
v5.1 using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types FUNCTION_WITHOUT_ARGS --fix-inplace -f {} \;
Change-Id: If104ac75b44e939ec86155ff7b5720f2e33c6b39
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5621
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Long strings are split across few lines; usually split occurs at
the white space between two words.
Check that the space between the two words is still present.
While there, adjust the amount of space between words.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types MISSING_SPACE -f {} \;
Change-Id: I28b9a65564195ba967051add53d1c848c7b8fb30
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5620
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Line continuation, adding a backslash as last char of the line, is
requested in multi-line macro definition, but is not necessary in
the rest of C code.
Remove it where present.
Identified by checkpatch script from Linux kernel v5.1 using the
command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types LINE_CONTINUATIONS -f {} \;
Change-Id: Id0c69e93456731717a7b290b16580e9f8ae741bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5619
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like parenthesis.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command:
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types SIZEOF_PARENTHESIS --fix-inplace -f {} \;
Change-Id: I8adb325bdb0e13211f8bae8b4770ec1979c176bf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5618
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
In a switch/case statement, a break placed after a goto or return
is never executed.
The script checkpatch available in Linux kernel v5.1 issues a
warning for such unused break statements.
In the process of reviewing the new checkpatch for its inclusion
in OpenOCD, let's get rid of these warnings.
The script checkpatch is unable to fixup automatically this case.
Thanks to having "break" command using a single code line, this
patch has been generated using the script below:
find src/ -type f -exec ./tools/scripts/checkpatch.pl -q \
--types UNNECESSARY_BREAK -f {} \; \
| sed -n '/^#/{s/^.*FILE: //;s/:$//;s/:/ /;p}' \
| awk 'function P() {print "sed -i '\''"b"'\'' "a};
{
if ($1!=a) {
if (a) {P()};
a=$1;
b=$2"{d}";
} else {
b=b";"$2"{d}"
}
};
END {P()}'
Change-Id: I56ca098faa5fe8d1e3f712dc0a029a3f10559d99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5617
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like spacing.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command:
find tcl/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types TRAILING_WHITESPACE --fix-inplace -f {} \;
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: Ie7e3a236f4db9c70019e3b3c7e851edbd3a9dd84
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5616
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
