This patch uses libjaylink which is a library to access J-Link
devices. As other tools which are not in the scope of OpenOCD also
need to access J-Link devices a library is used. A firmware upgrade
tool and an advanced configuration tool for J-Link devices are under
development.
Further versions of libjaylink will support additional features
OpenOCD could benefit from. This includes TCP/IP as additional
possibility to connect to J-Link devices as well as power tracing and
device internal communication. The latter is used to access
peripherals on some development boards (e.g EFM32 STK and DVK).
Integration of libjaylink is realized with a git submodule like
jimtcl. As libjaylink depends on libusb-1.0 only, no additional
dependency is introduced for OpenOCD.
All low-level JTAG and SWD implementations of the current driver are
left untouched and therefore no incompabilities are to be expected.
Improvements of this patch:
* Support for more USB Product IDs, including those with the new
scheme (0x10xx). The corresponding udev rules are also updated.
* Device selection with serial number and USB address.
* Adaptive clocking is now correctly implemented and only usable for
devices with the corresponding capability.
* The target power supply can now be switched without the need for
changing configuration and power cycling the device.
* Device configuration is more restrictive and only allowed if the
required capabilities are available.
* Device configuration now shows the changes between the current
configuration of the device and the values that will be applied.
* Device configuration is verified after it is written to the device
exactly as the vendor software does.
* Connection registration is now handled properly and checks if the
maximum number of connections on a device is reached. This is also
necessary for devices which are attached via USB to OpenOCD as
some device models also support connections on TCP/IP.
* Serial Wire Output (SWO) can now be captured. This feature is not
documented by SEGGER however it is completely supported by
libjaylink.
This patch and libjaylink were tested on Ubuntu 14.04 (i386),
Debian 7 (amd64), FreeBSD 10.0 (amd64) and Windows XP SP3 (32-bit)
with the following device and target configurations:
* JTAG: J-Link v8.0, v9.0 and v9.3 with AT91SAM7S256
* SWD: SiLabs EFM32 STK 3700 (EFM32GG990F1024)
* SWD: J-Link v8.0, v9.0 and v9.3 with EFM32GG990F1024
* SWD: XMC 2Go (XMC1100)
* SWD: XMC1100 Boot Kit (XMC1100)
* SWD: IAR Systems / Olimex Eval Board (LPC1343F)
* SWD: Nordic Semiconductor nRF51 Dongle (nRF51422)
* SWD: SiLabs EZR32 WSTK 6220A (EZR32WG330FG60G)
Except for Windows XP all builds are tested with Clang in addition to
GCC. This patch and libjaylink are not tested on OSX yet.
Change-Id: I8476c57d37c6091c4b892b183da682c548ca1786
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/2598
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
GPL requires providing sources for any derived work. I do not see any
reason to not include the rlink stuff into release tarballs.
Change-Id: I686ab88994030312aca5bdfe731a72f10803b5c3
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1907
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is based on work from:
https://github.com/TheShed/OpenOCD-CMSIS-DAP/tree/cmsis-dap
Main changes include moving over to using HIDAPI rather than libusb-1.0
and cleaning up to merge into master. Support for reset using srst has
also been added.
It has been tested on all the mbed boards as well as the Freedom board
from Freescale. These boards only implement SWD mode, however JTAG mode
has been tested with a Keil ULINK2 and a stm32 target - but requires a lot
more work.
Change-Id: I96d5ee1993bc9c0526219ab754c5aad3b55d812d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1542
Tested-by: jenkins
This unifies the way the USB adapters are handled, and enables them
automatically whenever possible (until explicitly disabled). If an
adapter is explicitly enabled but can't be built, abort the
configure.
Also add infrastructure for generic handling of adapter drivers in
configure and print a summary of the configuration results after
finishing.
The m4 quoting is as conservative as I could get it, and seems
appropriate.
Change-Id: I1655691e5ea0d8eb9e3f67830b96992ffe33640a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1475
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
An alternative approach to show how much cleaner the pure pkg-config
way is.
This changes the discovery procedures for libusb-1.0 and libusb-0.1,
making them depend on pkg-config being properly installed and
configured, including the necessary build host configuration for the
cross-builds (see
http://www.flameeyes.eu/autotools-mythbuster/pkgconfig/cross-compiling.html)
It should make it possible to compile OpenOCD without changes and
extra effort on GNU/Linux, FreeBSD users would need to supply a .pc
file for their libusb implementation or add LIBUSB1_LIBS and
LIBUSB1_CFLAGS to the configure environment.
Change-Id: I826e378dd1e0d101a549a573b2c63212a7e00b64
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1467
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds a driver for the jtag_vpi server [1]. This server is
now part of the ORPSoC version 3 (OpenRISC Reference Platform SoC).
The jtag_vpi server provides an interface between OpenOCD and a simulated
core.
[1] http://github.com/fjullien/jtag_vpi
Change-Id: I717b72cace4845f66c878581345074f99002e21a
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1609
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The precompiled OpenULINK firmware is just data to OpenOCD so I think it
belongs in $(prefix)/share/openocd rather than in $(prefix)/lib.
Change-Id: Id84c32cd0ddfb96861e903e8f23c16a81e1a0ca1
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1487
Tested-by: jenkins
Reviewed-by: Martin Schmölzer <martin.schmoelzer@student.tuwien.ac.at>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This makes libusb handling more consistent: if any driver requires
libusb, first check for libusb-1 availability, if not found and
libusb0 is ok for this case, try libusb0.
A user-visible bug fixed by this is that when a user was selecting a
driver that required libusb-1 but was lacking the necessary dev files
or libraries, configure didn't complain (but the build was failing of
course).
--enable-stlink doesn't really require libusb-1 but since it's using the
same automake symbol HLAADAPTER, ti_icdi is getting built too which needs
libusb1 unconditionally. Since using libusb-0.1 makes little sense anyway,
leave that as is.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Change-Id: I630a4ad9e4583743d45b2233bf5d8f4e5c0aab82
Reviewed-on: http://openocd.zylin.com/1434
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This adds support for JTAG programming by bitbanging GPIOs exposed on
the RaspberryPi's expansion header.
Tested by connecting directly to an STM32VLDiscovery board, without any
additional circuity. I observed maximum about 4MHz on the TCK pin with an
old analogue 'scope and about 100kHz when setting the speed to 100kHz.
Busyloop waiting is needed because even with a single 0ns nanosleep call
(with FIFO priority) it lowers the TCK speed to ~30kHz which is way too low
to be useful.
The speed testing with adapter_khz 2000 gave the following results:
sudo chrt -f 1 nice -n -19 ./src/openocd \
-f interface/raspberrypi-native.cfg \
-c "set WORKAREASIZE 0x2000" \
-f target/stm32f1x.cfg -c "adapter_khz 2000"
wrote 131072 bytes from file random.bin in 3.973677s (32.212 KiB/s)
dumped 131072 bytes in 1.445699s (88.538 KiB/s)
This is 3.7 times faster for writing and 14.3 times faster for reading
compared to the generic sysfsgpio driver; probably the writing speed is
limited by the target itself here and reading speed might be considerably
higher too with appropriate connection and a capable target.
BCM2835 name is choosen over BCM2708 because the published peripherals
datasheet uses the particular model name and not family name.
Change-Id: Ib78168be27f53c2a3c88c3dd8154d1190c318c78
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/758
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Updated OpenJTAG driver from www.openjtag.org to work with latest version of OpenOCD.
Change-Id: I2917f4e5835fb9ca5265e81dc38515fa97ae9503
Signed-off-by: Ryan Corbin <corbin.ryan@gmail.com>
Reviewed-on: http://openocd.zylin.com/1406
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Rewrite the Altera USB Blaster dongle driver :
- make extensive use of byte-shift mode, to improve JTAG
speed.
This is the main reason of the rewrite. It improves the
memory dumps with a factor 3 at least, and upload 100
times, from 1 kBytes/sec to 100 kBytes/sec with a
USB-Blaster connected to an Altera Virtual JTAG TAP +
OpenRISC CPU.
- split the low level API part (between FTDI and FTD2xx)
from core driver, so that in the future, if both libftdi
and ftd2xx can coexist, the driver will be able to switch
dynamically from one access to the other.
Change-Id: I2ee9cedf4a5eb27501f337993ee0cdee52517e7c
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Marek Czerski <ma.czerski@gmail.com>
Tested-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/467
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Alexandre Becoulet <alexandre.becoulet@free.fr>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This is the new proprietary interface replacing the older FTDI based adapters.
It is currently fitted to the ek-lm4f232 and Stellaris LaunchPad.
Change-Id: I794ad79e31ff61ec8e9f49530aca9308025c0b60
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/922
Tested-by: jenkins
This enables us to change the target name without breaking any
target scripts.
Change-Id: I635f961e573264d3dab2560f3a803ef1986ccfde
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/919
Tested-by: jenkins
This driver implements a bitbang jtag interface using gpio lines exported via
sysfs.
The aim of this driver implementation is to use system GPIOs but to avoid the
need for an additional kernel driver.
A config suitable for RaspberryPi is included.
Change-Id: Ib2acf720247a219768d1cbfeebd88057ed2d7b8b
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Reviewed-on: http://openocd.zylin.com/762
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
make distcheck is used to make packages with OpenOCD release, this
command uses information from Makefile.am files to know which files
should be included in the package and which can be left only in
repository. This patch makes a few headers from recent JTAG drivers
and one txt file with info about target tcl config files included in
released packages.
Change-Id: I91202290633a30f53624a8c7d9a0ebf72c40772b
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/767
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Based on ft2232.c but uses the MPSSE layer for low-level access, greatly
simplifying the JTAG logic. Remove all libftdi/FTD2XX code and all layout
specific code. Layout specifications are instead handled in Tcl.
Use a signal abstraction to enable Tcl configuration files to define
outputs for one or several FTDI GPIO. These outputs can then be
controlled using the ftdi_set_signal command. Special signal names are
reserved for nTRST, nSRST and LED (for blink) so that they, if defined,
will be used for their customary purpose.
Depending on the type of buffer attached to the FTDI GPIO, the outputs
have to be controlled differently. In order to support tristateable
signals such as nSRST, both a data GPIO and an output-enable GPIO can be
specified for each signal. The following output buffer configurations are
supported:
* Push-pull with one FTDI output as (non-)inverted data line
* Open drain with one FTDI output as (non-)inverted output-enable
* Tristate with one FTDI output as (non-)inverted data line and another
FTDI output as (non-)inverted output-enable
* Unbuffered, using the FTDI GPIO as a tristate output directly by
switching data and direction as necessary
The data and output-enables are specified as 16-bit bitmasks,
corresponding to the concatenation of the high and low FTDI GPIO
registers. To specify an unbuffered output, use the same bitmask
for both data and output-enable.
The adapter configuration file must also specify default values for the
FTDI data and direction GPIO registers, and the channel being used (if
different from 0).
Change-Id: I287a41d4c696cf5fc74eb10d5e63578b0dc7f826
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/452
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This driver provides support for the P&E Micro OSBDM adapter (sometimes
named as OSJTAG), mounted on the Freescale TWRK60N512 bord. Thus, it
provides a quick start when working with this board. The driver doesn't
use BDM commands, but work with OSBDM adapter using only JTAG commands.
Change-Id: Ibc3779538e666e07651d3136431e5d44344f3b07
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Reviewed-on: http://openocd.zylin.com/492
Tested-by: jenkins
Reviewed-by: Tomas Frydrych <tf+openocd@r-finger.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
automake 1.11.2 throws `pkglibdir' is not a legitimate directory for `DATA'
if nobase_dist_pkglib_DATA is used.
We work around this issue by defining our own location.
Change-Id: I3c29e2df0b67e745283c50d358e31699bd60dc74
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/457
Tested-by: jenkins
ST-Link USB support added.
Change-Id: I2812646f2895b1529ff3f911edbdce7fa0051c8f
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/261
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The configuration script check for libusb-1.0 availability first and only
if not found check for libusb-0. So if both libraries are installed on the
system the build script will use libusb-1.0
It's possible to force compiling with libusb-0 with the --enable-libusb0 switch.
If the driver support only libusb0 the script check anly for it.
Change-Id: I7eb045d4e2bd553abefad53f3f4023ff46b0f5f6
Signed-off-by: Mauro Gamba <maurillo71@gmail.com>
Reviewed-on: http://openocd.zylin.com/33
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The driver sends ascii encoded bitbang commands over unix sockets or TCP to
another process. This driver is useful for debugging software running on
processors which are being simulated.
A new variable "nobase_dist_pkglib_DATA" is introduced to install
the OpenULINK firmware image to $PREFIX/lib/openocd/OpenULINK/ulink_firmware.hex
Also, the variable "EXTRA_DIST" is used to include the OpenULINK firmware source
in the OpenOCD source distribution.
This includes a driver and matching config file. This support needs to be
enabled through the initial "configure" (use "--enable-buspirate").
Signed-off-by: Michal Demin <michaldemin@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The 10-pin JTAG layout used with these adapters is used by
a variety of platforms including AVR.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Includes the src directory in the search path, so header files may be
migrated from:
#include "foo.h"
to
#include <module/foo.h>
which is more conducive for installation.
Moves JTAG interface drivers to src/jtag/drivers/,
Adds src/jtag/drivers/Makefile.am.
Builds libocdjtagdrivers.la.
Flattens the rlink driver files into the drivers/ directory, adding
the 'rlink_' prefix or '.rlink' suffix as appropriate.
Marc Schink
Paul Fertser
Spencer Oliver
Franck Jullien
Andreas Fritiofson
Ryan Corbin
Robert Jarzmik
Marc Reilly
Freddie Chopin
Jan Dakinevich
Mathias K
Mauro Gamba
Richard Uhler
SimonQian
Martin Schmölzer
Spencer Oliver
Michal Demin
Catalin Patulea
Øyvind Harboe
Zachary T Welch