i had started my code from dsp5683xx, i renamed a bunch of stuff to names i consider to be better.
i believe no one is using this code, so nobody should be affected. (it's not too late to do this change)
Function mips_m4k_write_memory() does endianess byte swap,
but this procedure break one byte access (temporary array
overwrites content in buffer).
As a fix, this endianess swap and buffer affecting
is preformed only on hword and word accesses (not on byte access).
Pprogram that loads another program into memory is actually writing the
D- side cache.
The instructions it has loaded can't be executed until they reach the
I-cache.
After the instructions have been written, the loader should arrange to
write back any containing D-cache line and invalidate any locations
already in the I-cache.
For the MIPS Architecture Release2 cores, we can use synci command
that does this job.
For Release1 we must use "cache" instruction.
This patch adds MIPS32 CP0 coprocessor R/W routines,
as well as adequate commands to use these routines via
telnet interface.
Now is becomes possible to affect CP0 internal registers
and configure CPU directly from OpenOCD.
For all architectures we use distinct common magic number,
and this should be a uint32_t type.
Otherwise, comparison with macros will yield compilation
warning.
before doing anything with the flash module (FM) the clock divider must be set.
if erase_check was the first thing done with the FM after reset then an error would be generated because the clk divider was not set.
now erase_check sets the clk divider.
reorganized code to get rid of compiler warnings
the warning were related to allignment, i do not get these warning on my build system (i've tried setting the compiler flag but it doesn't work, still working on why) so i cannot detect them (yet.)
This corrects two issues found with openocd.
d7f71e7fe9 removed some code that was
being used.
The above then caused even more code to get removed by commit 1cfb2287a6.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
In order to compare data read from the target with some marcros or data
defined on the host, we must transform this read data from target
endianess to host endianess.
target_read_memory() gets bytes from target to the host, but keeps them in _target_
endianess. This is OK if we just want to temporary keep this data on the
host, like keeping breakpoint->orig_instr. But if we want to use this
data for any ispections and comparisons on the host side, we must
transform it to _host_ endianess, by using target_buffer_get_u32()
function.
Currently this transformation is missing, and check current_instr ==
MIPS32_SDBBP will never pass if target and host endianess differ,
because current_instr will be kept in _target_ endianess and
MIPS32_SDBBP will be kept in _host_ endianess,
The patch fix this issue by using target_buffer_get_u32() to transform current_instr to
_host_ endianess before comparison.
Use "git revert <commit>" to revert this commit, then build and
repair and post patch to the mailing list.
Warnings generated with:
nios2-elf-gcc (GCC) 3.4.6 (Altera Nios II 9.1 b222)
openocd/src/target/dsp5680xx.c: In function 'eonce_rx_upper_data':
openocd/src/target/dsp5680xx.c:252: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'eonce_rx_lower_data':
openocd/src/target/dsp5680xx.c:268: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'eonce_pc_store':
openocd/src/target/dsp5680xx.c:508: warning: dereferencing type-punned
pointer will break strict-aliasing rules
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_read':
openocd/src/target/dsp5680xx.c:736: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c:737: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_write_8':
openocd/src/target/dsp5680xx.c:823: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_write':
openocd/src/target/dsp5680xx.c:938: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c:941: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_f_wr':
openocd/src/target/dsp5680xx.c:1355: warning: cast increases required
alignment of target type
This patch extends the cortex_m3 maskisr command by a new option 'auto'.
The 'auto' option handles interrupts during stepping in a way they are
processed but don't disturb the program flow during debugging.
Before one had to choose to either enable or disable interrupts. The former
steps into interrupt handlers when they trigger. This disturbs the flow during
debugging, making it hard to follow some piece of code when interrupts occur
often.
When interrupts are disabled, the flow isn't disturbed but code relying on
interrupt handlers to be processed will stop working. For example a delay
function counting the number of timer interrupts will never complete, RTOS
task switching will not occur and output I/O queues of interrupt driven
I/O will stall or overflow.
Using the 'maskisr' command also typically requires gdb hooks to be supplied
by the user to switch interrupts off during the step and to enable them again
afterward.
The new 'auto' option of the 'maskisr' command solves the above problems. When
set, the step command allows pending interrupt handlers to be executed before
the step, then the step is taken with interrupts disabled and finally interrupts
are enabled again. This way interrupt processing stays in the background without
disturbing the flow of debugging. No gdb hooks are required. The 'auto'
option is the default, since it's believed that handling interrupts in this
way is suitable for most users.
The principle used for interrupt handling could probably be used for other
targets too.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
So far image_load command tries to load ELF binaries to address
discovered by reading p_paddr member of a Program header of an ELF
segment.
However, ELF specifications says for p_paddr : ...Because System V
ignores physical addressing for application programs, this member has
unspecified contents for executable files and shared objects.
ARM ELF specifiaction goes even further, demanding that this member
be set to zero, using the p_vaddr as a segment load address.
To avoid the cases to wrong addr where p_paddr is zero,
we are now using p_vaddr to as a load destination in case that *all*
p_paddr == 0. Basically, this patch re-implements the approach present in
BDF's elf.c, which is used by GDB also (so that we can be consistent).
