To simplify things change over to using the generic core_mode struct rather
than maintaining a armv7m specific one.
Change-Id: Ibf32b785d896fef4f33307fabe0d8eb266f7086f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/966
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
An issue has been seen with the stm32lx flash driver that if a
power cycle/reset is applied after a erase, any ram loader will Hard Fault
on execution.
A similar issue is mentioned in the errata for the device.
Two solution's seem to workaround this issue:
1, Handle the exception, this means adding exception vectors to the loader
and changing the exception address using nvic vtor register.
2. falling back to using slower direct page writes - approx 50% slower.
Using solution 1 would mean restrictions are placed on the loader location.
Solution 2 was chosen mainly as it was simpler too implement.
Change-Id: I429f06b5a3e3b1d8de90071a88a7df11fc9b46a7
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1010
Tested-by: jenkins
Waiting 20secs is a bit much excessive, we could probably reduce to 5.
Change-Id: Iffb97adb99c2541a075fe78dbc88a53ddf340214
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1009
Tested-by: jenkins
Handle any leading bytes upto the next 128 byte page, enabling us to safely
use the faster page write.
Rather than use a separate word/byte write to program any trailing bytes
we use a combined write function.
Use memcpy for byte writes and change loader to using bytes.
Change-Id: Ie0164a30388f018dd00e752cf5ff87d4f96ced97
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1008
Tested-by: jenkins
The current stm32lx driver will fail if no working area is
provided - fallback to using slow writes if this is the case.
Change-Id: I92b1535fec4aebc855c63ce2c54b10f168f3c07e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1007
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Working area pointers shouldn't be re-used, so there's no point in storing
them in the flash bank struct. Make all such pointers local.
Change-Id: Iab65b4e8b475fed7fc72fb8928f54590fa69d260
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/865
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove a lot of the repetitive code in stm32f1x flash probe by converting
the large if-selector to a switch, moving the common checks outside it and
concentrating the failure handling to a single point.
Do the same with stm32f2x and stm32lx for consistency.
Change-Id: Ic0ecfb1533c49f5d2108cda5fd20c8372d7c71ef
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/746
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Some variants read 0 for the flash size register, rather than
failing lets assume we have max flash fitted.
Change-Id: Ie1fb4e73606f49268a6fd5921c3aef75bc4790d3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/744
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Rather than failing if the flash size reg cannot be read lets assume
we have the max flash size fitted.
It is quite common on early ST silicon to not correct support this register.
Change-Id: Ife058d60ae0027faad2c929ebd5b7fe2ef27234d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/743
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Revision X is not mentioned in the latest RM0038 rev5, however it has been
confirmed correct by ST using ST-LINK Utilty.
Change-Id: I65210e512ea25818a1d0d3b223502ebd7535b29d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/742
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The target address for the partial data needs to be bumped past the
full page data. Otherwise, the partial data overwrites the start of
the flash block.
Change-Id: I1246b2fa8acbdb8193edcf7029309f11d1c6069c
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/555
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Currently stm32lx flash driver will remove the readout protection if set
during a probe.
This may not be what the user wants, so let them decide.
Change-Id: I8575e3b339b10a4f7bac57cca9586dcab513d347
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/465
Tested-by: jenkins
The stm32 drivers have been using 0x7ff as the DEV_ID mask, this should
have been 0xfff.
Change-Id: I232469620969d6dd1b9a2a2aa15ec18b947dbb05
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/352
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
There is no need to use a while loop here. This patch simple copy
the last bytes with the system function.
Change-Id: Ibda72dca449746efeba5a1af2e45c5990f9cf347
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/364
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On wrong parameters a error is signalized to the calling function.
Change-Id: I484443fdb39938e20382edc9246d5ec546a5c960
Signed-off-by: Mathias K <kesmtp@freenet.de>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/282
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
