openocd/tcl/board/sheevaplug.cfg

138 lines
4.7 KiB
INI

# SPDX-License-Identifier: GPL-2.0-or-later
# Marvell SheevaPlug
source [find interface/ftdi/sheevaplug.cfg]
source [find target/feroceon.cfg]
adapter speed 2000
$_TARGETNAME configure \
-work-area-phys 0x10000000 \
-work-area-size 65536 \
-work-area-backup 0
arm7_9 dcc_downloads enable
# this assumes the hardware default peripherals location before u-Boot moves it
set _FLASHNAME $_CHIPNAME.flash
nand device $_FLASHNAME orion 0 0xd8000000
proc sheevaplug_init { } {
# We need to assert DBGRQ while holding nSRST down.
# However DBGACK will be set only when nSRST is released.
# Furthermore, the JTAG interface doesn't respond at all when
# the CPU is in the WFI (wait for interrupts) state, so it is
# possible that initial tap examination failed. So let's
# re-examine the target again here when nSRST is asserted which
# should then succeed.
adapter assert srst
feroceon.cpu arp_examine
halt 0
adapter deassert srst
wait_halt
arm mcr 15 0 0 1 0 0x00052078
mww 0xD0001400 0x43000C30 ;# DDR SDRAM Configuration Register
mww 0xD0001404 0x39543000 ;# Dunit Control Low Register
mww 0xD0001408 0x22125451 ;# DDR SDRAM Timing (Low) Register
mww 0xD000140C 0x00000833 ;# DDR SDRAM Timing (High) Register
mww 0xD0001410 0x000000CC ;# DDR SDRAM Address Control Register
mww 0xD0001414 0x00000000 ;# DDR SDRAM Open Pages Control Register
mww 0xD0001418 0x00000000 ;# DDR SDRAM Operation Register
mww 0xD000141C 0x00000C52 ;# DDR SDRAM Mode Register
mww 0xD0001420 0x00000042 ;# DDR SDRAM Extended Mode Register
mww 0xD0001424 0x0000F17F ;# Dunit Control High Register
mww 0xD0001428 0x00085520 ;# Dunit Control High Register
mww 0xD000147c 0x00008552 ;# Dunit Control High Register
mww 0xD0001504 0x0FFFFFF1 ;# CS0n Size Register
mww 0xD0001508 0x10000000 ;# CS1n Base Register
mww 0xD000150C 0x0FFFFFF5 ;# CS1n Size Register
mww 0xD0001514 0x00000000 ;# CS2n Size Register
mww 0xD000151C 0x00000000 ;# CS3n Size Register
mww 0xD0001494 0x003C0000 ;# DDR2 SDRAM ODT Control (Low) Register
mww 0xD0001498 0x00000000 ;# DDR2 SDRAM ODT Control (High) REgister
mww 0xD000149C 0x0000F80F ;# DDR2 Dunit ODT Control Register
mww 0xD0001480 0x00000001 ;# DDR SDRAM Initialization Control Register
mww 0xD0020204 0x00000000 ;# Main IRQ Interrupt Mask Register
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0020204 0x00000000 ;# "
mww 0xD0010000 0x01111111 ;# MPP 0 to 7
mww 0xD0010004 0x11113322 ;# MPP 8 to 15
mww 0xD0010008 0x00001111 ;# MPP 16 to 23
mww 0xD0010418 0x003E07CF ;# NAND Read Parameters REgister
mww 0xD001041C 0x000F0F0F ;# NAND Write Parameters Register
mww 0xD0010470 0x01C7D943 ;# NAND Flash Control Register
}
proc sheevaplug_reflash_uboot { } {
# reflash the u-Boot binary and reboot into it
sheevaplug_init
nand probe 0
nand erase 0 0x0 0xa0000
nand write 0 uboot.bin 0 oob_softecc_kw
resume
}
proc sheevaplug_reflash_uboot_env { } {
# reflash the u-Boot environment variables area
sheevaplug_init
nand probe 0
nand erase 0 0xa0000 0x40000
nand write 0 uboot-env.bin 0xa0000 oob_softecc_kw
resume
}
proc sheevaplug_load_uboot { } {
# load u-Boot into RAM and execute it
sheevaplug_init
load_image uboot.elf
verify_image uboot.elf
resume 0x00600000
}