38ac08c1c2
Avoid annoying "deprecated" messages while running the scripts distributed with OpenOCD code. Change automatically created with commands sed -i 's/adapter_khz/adapter speed/g' $(find tcl/ -type f) sed -i 's/adapter_nsrst_delay/adapter srst delay/g' $(find tcl/ -type f) sed -i 's/adapter_nsrst_assert_width/adapter srst pulse_width/g' $(find tcl/ -type f) Minor indentation issue fixed manually in tcl/board/at91sam9g20-ek.cfg tcl/target/at91sam9260_ext_RAM_ext_flash.cfg Change-Id: I425fd56c0c88cd6b06124621306eeb89166dfe71 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5284 Tested-by: jenkins Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
65 lines
1.6 KiB
INI
65 lines
1.6 KiB
INI
#
|
|
# script for ATMEL sam4, a Cortex-M4 chip
|
|
#
|
|
|
|
#
|
|
# sam4 devices can support both JTAG and SWD transports.
|
|
#
|
|
source [find target/swj-dp.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME sam4
|
|
}
|
|
|
|
if { [info exists ENDIAN] } {
|
|
set _ENDIAN $ENDIAN
|
|
} else {
|
|
set _ENDIAN little
|
|
}
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 64kB
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x4000
|
|
}
|
|
|
|
#jtag scan chain
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
set _CPUTAPID 0x4ba00477
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
|
|
|
|
# 16K is plenty, the smallest chip has this much
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
# JTAG speed should be <= F_CPU/6. F_CPU after reset is 4 MHz, so use F_JTAG = 0.5MHz
|
|
#
|
|
# Since we may be running of an RC oscilator, we crank down the speed a
|
|
# bit more to be on the safe side. Perhaps superstition, but if are
|
|
# running off a crystal, we can run closer to the limit. Note
|
|
# that there can be a pretty wide band where things are more or less stable.
|
|
|
|
adapter speed 500
|
|
|
|
adapter srst delay 100
|
|
if {[using_jtag]} {
|
|
jtag_ntrst_delay 100
|
|
}
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
cortex_m reset_config sysresetreq
|
|
}
|