1c021ed0af
Remove this underutilized feature. Despite the fact that a lot of configs specifies a arbitrary "variant", only the xscale target actually defines any. In the case of xscale, the use of -variant is dubious since 1) it's used as a redundant irlen specifier, 2) it carries a comment that it doesn't really need it and 3) only two xscale configs even specify it. If there's a future target that needs a variant set, a target specific option could be added when needed. Change-Id: I1ba25a946f0d80872cbd96ddcc48f92695c4ae20 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2283 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
55 lines
1.4 KiB
INI
55 lines
1.4 KiB
INI
#STR730 CPU
|
|
|
|
adapter_khz 3000
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME str730
|
|
}
|
|
|
|
if { [info exists ENDIAN] } {
|
|
set _ENDIAN $ENDIAN
|
|
} else {
|
|
set _ENDIAN little
|
|
}
|
|
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
set _CPUTAPID 0x3f0f0f0f
|
|
}
|
|
|
|
#use combined on interfaces or targets that can't set TRST/SRST separately
|
|
reset_config trst_and_srst srst_pulls_trst
|
|
|
|
#jtag scan chain
|
|
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0f -expected-id $_CPUTAPID
|
|
|
|
#jtag nTRST and nSRST delay
|
|
adapter_nsrst_delay 500
|
|
jtag_ntrst_delay 500
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME arm7tdmi -endian little -chain-position 0
|
|
|
|
$_TARGETNAME configure -event reset-start { adapter_khz 10 }
|
|
$_TARGETNAME configure -event reset-init {
|
|
adapter_khz 3000
|
|
|
|
# Because the hardware cannot be interrogated for the protection state
|
|
# of sectors, initialize all the sectors to be unprotected. The initial
|
|
# state is reflected by the driver, too.
|
|
flash protect 0 0 last off
|
|
}
|
|
$_TARGETNAME configure -event gdb-flash-erase-start {
|
|
flash protect 0 0 7 off
|
|
}
|
|
|
|
$_TARGETNAME configure -work-area-phys 0xA0000000 -work-area-size 0x4000 -work-area-backup 0
|
|
|
|
#flash bank <driver> <base> <size> <chip_width> <bus_width>
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME str7x 0x80000000 0x00040000 0 0 $_TARGETNAME STR73x
|
|
|