38ac08c1c2
Avoid annoying "deprecated" messages while running the scripts distributed with OpenOCD code. Change automatically created with commands sed -i 's/adapter_khz/adapter speed/g' $(find tcl/ -type f) sed -i 's/adapter_nsrst_delay/adapter srst delay/g' $(find tcl/ -type f) sed -i 's/adapter_nsrst_assert_width/adapter srst pulse_width/g' $(find tcl/ -type f) Minor indentation issue fixed manually in tcl/board/at91sam9g20-ek.cfg tcl/target/at91sam9260_ext_RAM_ext_flash.cfg Change-Id: I425fd56c0c88cd6b06124621306eeb89166dfe71 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5284 Tested-by: jenkins Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
62 lines
1.5 KiB
INI
62 lines
1.5 KiB
INI
#
|
|
# script for Nordic nRF51 series, a Cortex-M0 chip
|
|
#
|
|
|
|
source [find target/swj-dp.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME nrf51
|
|
}
|
|
|
|
if { [info exists ENDIAN] } {
|
|
set _ENDIAN $ENDIAN
|
|
} else {
|
|
set _ENDIAN little
|
|
}
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 16kB
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x4000
|
|
}
|
|
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
set _CPUTAPID 0x0bb11477
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -expected-id $_CPUTAPID
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -dap $_CHIPNAME.dap
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
if {![using_hla]} {
|
|
# The chip supports standard ARM/Cortex-M0 SYSRESETREQ signal
|
|
cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
flash bank $_CHIPNAME.flash nrf51 0x00000000 0 1 1 $_TARGETNAME
|
|
flash bank $_CHIPNAME.uicr nrf51 0x10001000 0 1 1 $_TARGETNAME
|
|
|
|
#
|
|
# The chip should start up from internal 16Mhz RC, so setting adapter
|
|
# clock to 1Mhz should be OK
|
|
#
|
|
adapter speed 1000
|
|
|
|
proc enable_all_ram {} {
|
|
# nRF51822 Product Anomaly Notice (PAN) #16 explains that not all RAM banks
|
|
# are reliably enabled after reset on some revisions (contrary to spec.) So after
|
|
# resetting we enable all banks via the RAMON register
|
|
mww 0x40000524 0xF
|
|
}
|
|
$_TARGETNAME configure -event reset-end { enable_all_ram }
|