1c021ed0af
Remove this underutilized feature. Despite the fact that a lot of configs specifies a arbitrary "variant", only the xscale target actually defines any. In the case of xscale, the use of -variant is dubious since 1) it's used as a redundant irlen specifier, 2) it carries a comment that it doesn't really need it and 3) only two xscale configs even specify it. If there's a future target that needs a variant set, a target specific option could be added when needed. Change-Id: I1ba25a946f0d80872cbd96ddcc48f92695c4ae20 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2283 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
52 lines
1.5 KiB
INI
52 lines
1.5 KiB
INI
#use combined on interfaces or targets that can't set TRST/SRST separately
|
|
reset_config srst_only srst_pulls_trst
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME sam7x512
|
|
}
|
|
|
|
if { [info exists ENDIAN] } {
|
|
set _ENDIAN $ENDIAN
|
|
} else {
|
|
set _ENDIAN little
|
|
}
|
|
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
set _CPUTAPID 0x3f0f0f0f
|
|
}
|
|
|
|
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
# disable watchdog
|
|
mww 0xfffffd44 0x00008000
|
|
# enable user reset
|
|
mww 0xfffffd08 0xa5000001
|
|
# CKGR_MOR : enable the main oscillator
|
|
mww 0xfffffc20 0x00000601
|
|
sleep 10
|
|
# CKGR_PLLR: 96.1097 MHz
|
|
mww 0xfffffc2c 0x00481c0e
|
|
sleep 10
|
|
# PMC_MCKR : MCK = PLL / 2 ~= 48 MHz
|
|
mww 0xfffffc30 0x00000007
|
|
sleep 10
|
|
# MC_FMR: flash mode (FWS=1,FMCN=60)
|
|
mww 0xffffff60 0x003c0100
|
|
sleep 100
|
|
}
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0
|
|
|
|
#flash bank <driver> <base_addr> <size> <chip_width> <bus_width> <target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector> <page_size> <num_nvmbits> <ext_freq_khz>]
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME.0 at91sam7 0 0 0 0 $_TARGETNAME 0 0 0 0 0 0 0 18432
|
|
flash bank $_FLASHNAME.1 at91sam7 0 0 0 0 $_TARGETNAME 1 0 0 0 0 0 0 18432
|