6090a5b158
Add 2 target files: -stm32h7x.cfg -stm32h7x_dual_bank.cfg Add 2 config files for: -STM32H743zi-nucleo bord -STM32H743i and STM32H753i eval boards. Change-Id: I2aae2c5acff4f3ff8e1bf232fda5a11a87f71703 Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com> Reviewed-on: http://openocd.zylin.com/4182 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
94 lines
2.2 KiB
INI
94 lines
2.2 KiB
INI
# script for stm32h7x family
|
|
|
|
#
|
|
# stm32h7 devices support both JTAG and SWD transports.
|
|
#
|
|
source [find target/swj-dp.tcl]
|
|
source [find mem_helper.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME stm32h7x
|
|
}
|
|
|
|
set _ENDIAN little
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 64kB
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x10000
|
|
}
|
|
|
|
#jtag scan chain
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
if { [using_jtag] } {
|
|
set _CPUTAPID 0x6ba00477
|
|
} {
|
|
set _CPUTAPID 0x6ba02477
|
|
}
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
|
|
if {[using_jtag]} {
|
|
swj_newdap $_CHIPNAME bs -irlen 5
|
|
}
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
set _FLASHNAME $_CHIPNAME.flash
|
|
flash bank $_FLASHNAME stm32h7x 0x08000000 0 0 0 $_TARGETNAME
|
|
|
|
# Clock after reset is HSI at 64 MHz, no need of PLL
|
|
adapter_khz 1800
|
|
|
|
adapter_nsrst_delay 100
|
|
if {[using_jtag]} {
|
|
jtag_ntrst_delay 100
|
|
}
|
|
|
|
# use hardware reset, connect under reset
|
|
reset_config srst_only srst_nogate
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
$_TARGETNAME configure -event examine-end {
|
|
# Enable D3 and D1 DBG clocks
|
|
# DBGMCU_CR |= D3DBGCKEN | D1DBGCKEN
|
|
mmw 0x5C001004 0x00600000 0
|
|
|
|
# Enable debug during low power modes (uses more power)
|
|
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP in D3 & D1 Domains
|
|
mmw 0x5C001004 0x00000187 0
|
|
|
|
# Stop watchdog counters during halt
|
|
# DBGMCU_APB3FZ1 |= WWDG1
|
|
mmw 0x5C001034 0x00000040 0
|
|
# DBGMCU_APB4FZ1 |= WDGLSD1
|
|
mmw 0x5C001054 0x00040000 0
|
|
}
|
|
|
|
$_TARGETNAME configure -event trace-config {
|
|
# Set TRACECLKEN; TRACE_MODE is set to async; when using sync
|
|
# change this value accordingly to configure trace pins
|
|
# assignment
|
|
mmw 0x5C001004 0x00100000 0
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
# Clock after reset is HSI at 64 MHz, no need of PLL
|
|
adapter_khz 4000
|
|
}
|