2231da8ec4
- add 'dap create' command to create dap instances - move all dap subcmmand into the dap instance commands - keep 'dap info' for convenience - change all armv7 and armv8 targets to take a dap instance instead of a jtag chain position - restructure tap/dap/target relations, jtag tap no longer references the dap, daps are now independently created and initialized. - clean up swd connect - re-initialize DAP also on JTAG errors (e.g. after reset, power cycle) - update documentation - update target files Change-Id: I322cf3969b5407c25d1d3962f9d9b9bc1df067d9 Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com> Reviewed-on: http://openocd.zylin.com/4468 Tested-by: jenkins Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
76 lines
2.4 KiB
INI
76 lines
2.4 KiB
INI
#
|
|
# NXP (former Freescale) Kinetis KL series devices
|
|
# Also used for Cortex-M0+ equipped members of KVx and KE1xZ series
|
|
#
|
|
|
|
source [find target/swj-dp.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME klx
|
|
}
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 1KiB
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x400
|
|
}
|
|
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
set _CPUTAPID 0x0bc11477
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -dap $_CHIPNAME.dap
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
set _FLASHNAME $_CHIPNAME.pflash
|
|
flash bank $_FLASHNAME kinetis 0 0 0 0 $_TARGETNAME
|
|
kinetis create_banks
|
|
|
|
# Table 5-1. Clock Summary of KL25 Sub-Family Reference Manual
|
|
# specifies up to 1MHz for VLPR mode and up to 24MHz for run mode;
|
|
# Table 17 of Sub-Family Data Sheet rev4 lists 25MHz as the maximum frequency.
|
|
adapter_khz 1000
|
|
|
|
reset_config srst_nogate
|
|
|
|
if {[using_hla]} {
|
|
echo ""
|
|
echo "!!!!!!!!!!!!!!!!!!!!!! WARNING !!!!!!!!!!!!!!!!! WARNING !!!!!!!!!!!!!!!!!!!!!!"
|
|
echo " Kinetis MCUs have a MDM-AP dedicated mainly to MCU security related functions."
|
|
echo " A high level adapter (like a ST-Link) you are currently using cannot access"
|
|
echo " the MDM-AP, so commands like 'mdm mass_erase' are not available in your"
|
|
echo " configuration. Also security locked state of the device will not be reported."
|
|
echo ""
|
|
echo " Be very careful as you can lock the device though there is no way to unlock"
|
|
echo " it without mass erase. Don't set write protection on the first block."
|
|
echo "!!!!!!!!!!!!!!!!!!!!!! WARNING !!!!!!!!!!!!!!!!! WARNING !!!!!!!!!!!!!!!!!!!!!!"
|
|
echo ""
|
|
} {
|
|
# Detect secured MCU or boot lock-up in RESET/WDOG loop
|
|
$_CHIPNAME.cpu configure -event examine-start {
|
|
kinetis mdm check_security
|
|
}
|
|
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
# Disable watchdog not to disturb OpenOCD algorithms running on MCU
|
|
# (e.g. armv7m_checksum_memory() in verify_image)
|
|
# Flash driver also disables watchdog before FTFA flash programming.
|
|
$_TARGETNAME configure -event reset-init {
|
|
kinetis disable_wdog
|
|
}
|