b8fd9aecb1
this is a rework of #5320 started by Andreas then abandoned. same syntax as in stm32f2x driver: enable OTP for writing > stm32l4x otp 1 enable write to OTP > flash write_bank 1 foo.bin 0 > flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1 read OTP > mdw 0x1FFF7000 4 disable OTP > stm32l4x otp 1 disable Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2 Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com> Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-on: http://openocd.zylin.com/5537 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
89 lines
2.3 KiB
INI
89 lines
2.3 KiB
INI
# script for stm32g0x family
|
|
|
|
#
|
|
# stm32g0 devices support SWD transports only.
|
|
#
|
|
source [find target/swj-dp.tcl]
|
|
source [find mem_helper.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME stm32g0x
|
|
}
|
|
|
|
set _ENDIAN little
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# Smallest proposed target has 8kB ram, use 4kB by default to avoid surprises
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x1000
|
|
}
|
|
|
|
#jtag scan chain
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
# Section 37.5.5 - corresponds to Cortex-M0+
|
|
set _CPUTAPID 0x0bc11477
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
flash bank $_CHIPNAME.flash stm32l4x 0x08000000 0 0 0 $_TARGETNAME
|
|
flash bank $_CHIPNAME.otp stm32l4x 0x1fff7000 0 0 0 $_TARGETNAME
|
|
|
|
# reasonable default
|
|
adapter speed 2000
|
|
|
|
adapter srst delay 100
|
|
if {[using_jtag]} {
|
|
jtag_ntrst_delay 100
|
|
}
|
|
|
|
reset_config srst_nogate
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
proc stm32g0x_default_reset_start {} {
|
|
# Reset clock is HSI16 (16 MHz)
|
|
adapter speed 2000
|
|
}
|
|
|
|
proc stm32g0x_default_examine_end {} {
|
|
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP
|
|
mmw 0x40015804 0x00000006 0
|
|
|
|
# Stop watchdog counters during halt
|
|
# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
|
|
mmw 0x40015808 0x00001800 0
|
|
}
|
|
|
|
proc stm32g0x_default_reset_init {} {
|
|
# Increase clock to 64 Mhz
|
|
mmw 0x40022000 0x00000002 0x00000005 ;# FLASH_ACR: Latency = 2
|
|
mww 0x4002100C 0x30000802 ;# RCC_PLLCFGR = PLLR=/2, PLLN=8, PLLM=/1, PLLSRC=0x2
|
|
mmw 0x40021000 0x01000000 0x00000000 ;# RCC_CR |= PLLON
|
|
mmw 0x40021008 0x00000002 0x00000005 ;# RCC_CFGR: SW=PLLRCLK
|
|
|
|
# Boost JTAG frequency
|
|
adapter speed 4000
|
|
}
|
|
|
|
# Default hooks
|
|
$_TARGETNAME configure -event examine-end { stm32g0x_default_examine_end }
|
|
$_TARGETNAME configure -event reset-start { stm32g0x_default_reset_start }
|
|
$_TARGETNAME configure -event reset-init { stm32g0x_default_reset_init }
|