2bc24c06d3
Previously the adapter speed settings were hard-coded to connect with low speed then switch over to high speed regardless what was mentioned in the cfg files. Now the stm8 target intercept adapter speed settings and configure the stm8 control registers accordingly. Change-Id: I7419514e5214e4b43b9d51253cf5b7f04a233533 Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com> Reviewed-on: http://openocd.zylin.com/5548 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
87 lines
1.8 KiB
INI
87 lines
1.8 KiB
INI
# script for stm8s family
|
|
|
|
#
|
|
# stm8 devices support SWIM transports only.
|
|
#
|
|
|
|
transport select swim
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME stm8s
|
|
}
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 1kB
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x400
|
|
}
|
|
|
|
if { [info exists FLASHSTART] } {
|
|
set _FLASHSTART $FLASHSTART
|
|
} else {
|
|
set _FLASHSTART 0x8000
|
|
}
|
|
|
|
if { [info exists FLASHEND] } {
|
|
set _FLASHEND $FLASHEND
|
|
} else {
|
|
set _FLASHEND 0xffff
|
|
}
|
|
|
|
if { [info exists EEPROMSTART] } {
|
|
set _EEPROMSTART $EEPROMSTART
|
|
} else {
|
|
set _EEPROMSTART 0x4000
|
|
}
|
|
|
|
if { [info exists EEPROMEND] } {
|
|
set _EEPROMEND $EEPROMEND
|
|
} else {
|
|
set _EEPROMEND 0x43ff
|
|
}
|
|
|
|
if { [info exists OPTIONSTART] } {
|
|
set _OPTIONSTART $OPTIONSTART
|
|
} else {
|
|
set _OPTIONSTART 0x4800
|
|
}
|
|
|
|
if { [info exists OPTIONEND] } {
|
|
set _OPTIONEND $OPTIONEND
|
|
} else {
|
|
set _OPTIONEND 0x487f
|
|
}
|
|
|
|
if { [info exists BLOCKSIZE] } {
|
|
set _BLOCKSIZE $BLOCKSIZE
|
|
} else {
|
|
set _BLOCKSIZE 0x80
|
|
}
|
|
|
|
swim newtap $_CHIPNAME cpu
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
|
|
target create $_TARGETNAME stm8 -chain-position $_CHIPNAME.cpu
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x0 -work-area-size $_WORKAREASIZE -work-area-backup 1
|
|
$_TARGETNAME configure -flashstart $_FLASHSTART -flashend $_FLASHEND -eepromstart $_EEPROMSTART -eepromend $_EEPROMEND
|
|
$_TARGETNAME configure -optionstart $_OPTIONSTART -optionend $_OPTIONEND -blocksize $_BLOCKSIZE
|
|
|
|
# Uncomment this line to enable interrupts while instruction step
|
|
#$_TARGETNAME configure -enable_step_irq
|
|
|
|
# Set high speed
|
|
adapter speed 800
|
|
# Set low speed
|
|
#adapter speed 363
|
|
|
|
reset_config srst_only
|
|
|
|
# uncomment this line to connect under reset
|
|
#reset_config srst_nogate connect_assert_srst
|