b8fd9aecb1
this is a rework of #5320 started by Andreas then abandoned. same syntax as in stm32f2x driver: enable OTP for writing > stm32l4x otp 1 enable write to OTP > flash write_bank 1 foo.bin 0 > flash filld 0x1FFF7000 0xDeadBeafBaadF00d 1 read OTP > mdw 0x1FFF7000 4 disable OTP > stm32l4x otp 1 disable Change-Id: Id7d7c163b35d7a3f406dc200d7e2fc293b0675c2 Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com> Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-on: http://openocd.zylin.com/5537 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
121 lines
3.3 KiB
INI
121 lines
3.3 KiB
INI
# script for stm32l4x family
|
|
|
|
#
|
|
# stm32l4 devices support both JTAG and SWD transports.
|
|
#
|
|
source [find target/swj-dp.tcl]
|
|
source [find mem_helper.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME stm32l4x
|
|
}
|
|
|
|
set _ENDIAN little
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# Smallest current target has 64kB ram, use 32kB by default to avoid surprises
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x8000
|
|
}
|
|
|
|
#jtag scan chain
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
if { [using_jtag] } {
|
|
# See STM Document RM0351
|
|
# Section 44.6.3 - corresponds to Cortex-M4 r0p1
|
|
set _CPUTAPID 0x4ba00477
|
|
} {
|
|
set _CPUTAPID 0x2ba01477
|
|
}
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
|
|
|
if {[using_jtag]} {
|
|
jtag newtap $_CHIPNAME bs -irlen 5
|
|
}
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
flash bank $_CHIPNAME.flash stm32l4x 0x08000000 0 0 0 $_TARGETNAME
|
|
flash bank $_CHIPNAME.otp stm32l4x 0x1fff7000 0 0 0 $_TARGETNAME
|
|
|
|
if { [info exists QUADSPI] && $QUADSPI } {
|
|
set a [llength [flash list]]
|
|
set _QSPINAME $_CHIPNAME.qspi
|
|
flash bank $_QSPINAME stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
|
|
} else {
|
|
if { [info exists OCTOSPI1] && $OCTOSPI1 } {
|
|
set a [llength [flash list]]
|
|
set _OCTOSPINAME1 $_CHIPNAME.octospi1
|
|
flash bank $_OCTOSPINAME1 stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
|
|
}
|
|
if { [info exists OCTOSPI2] && $OCTOSPI2 } {
|
|
set b [llength [flash list]]
|
|
set _OCTOSPINAME2 $_CHIPNAME.octospi2
|
|
flash bank $_OCTOSPINAME2 stmqspi 0x70000000 0 0 0 $_TARGETNAME 0xA0001400
|
|
}
|
|
}
|
|
|
|
# Common knowledges tells JTAG speed should be <= F_CPU/6.
|
|
# F_CPU after reset is MSI 4MHz, so use F_JTAG = 500 kHz to stay on
|
|
# the safe side.
|
|
#
|
|
# Note that there is a pretty wide band where things are
|
|
# more or less stable, see http://openocd.zylin.com/#/c/3366/
|
|
adapter speed 500
|
|
|
|
adapter srst delay 100
|
|
if {[using_jtag]} {
|
|
jtag_ntrst_delay 100
|
|
}
|
|
|
|
reset_config srst_nogate
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
cortex_m reset_config sysresetreq
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
# CPU comes out of reset with MSI_ON | MSI_RDY | MSI Range 6 (4 MHz).
|
|
# Use MSI 24 MHz clock, compliant even with VOS == 2.
|
|
# 3 WS compliant with VOS == 2 and 24 MHz.
|
|
mww 0x40022000 0x00000103 ;# FLASH_ACR = PRFTBE | 3(Latency)
|
|
mww 0x40021000 0x00000099 ;# RCC_CR = MSI_ON | MSIRGSEL | MSI Range 9
|
|
# Boost JTAG frequency
|
|
adapter speed 4000
|
|
}
|
|
|
|
$_TARGETNAME configure -event reset-start {
|
|
# Reset clock is MSI (4 MHz)
|
|
adapter speed 500
|
|
}
|
|
|
|
$_TARGETNAME configure -event examine-end {
|
|
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
|
|
mmw 0xE0042004 0x00000007 0
|
|
|
|
# Stop watchdog counters during halt
|
|
# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
|
|
mmw 0xE0042008 0x00001800 0
|
|
}
|
|
|
|
$_TARGETNAME configure -event trace-config {
|
|
# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
|
|
# change this value accordingly to configure trace pins
|
|
# assignment
|
|
mmw 0xE0042004 0x00000020 0
|
|
}
|