0c8ec7c826
It's Cortex-Xn, not Cortex Xn or cortex xn or cortex-xn or CORTEX-Xn or CortexXn. Further it's Cortex-M0+, not M0plus. Cf. http://www.arm.com/products/processors/index.php Consistently write it the official way, so that it stops propagating. Originally spotted in the documentation, it mainly affects code comments but also Atmel SAM3/SAM4/SAMV, NiietCM4 and SiM3x flash driver output. Found via: git grep -i "Cortex " git grep -i "Cortex-" | grep -v "Cortex-" | grep -v ".cpu" git grep -i "CortexM" Change-Id: Ic7b6ca85253e027f6f0f751c628d1a2a391fe914 Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-on: http://openocd.zylin.com/3483 Tested-by: jenkins Reviewed-by: Marc Schink <openocd-dev@marcschink.de> Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
64 lines
1.5 KiB
INI
64 lines
1.5 KiB
INI
#
|
|
# script for ATMEL sam4, a Cortex-M4 chip
|
|
#
|
|
|
|
#
|
|
# sam4 devices can support both JTAG and SWD transports.
|
|
#
|
|
source [find target/swj-dp.tcl]
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME sam4
|
|
}
|
|
|
|
if { [info exists ENDIAN] } {
|
|
set _ENDIAN $ENDIAN
|
|
} else {
|
|
set _ENDIAN little
|
|
}
|
|
|
|
# Work-area is a space in RAM used for flash programming
|
|
# By default use 64kB
|
|
if { [info exists WORKAREASIZE] } {
|
|
set _WORKAREASIZE $WORKAREASIZE
|
|
} else {
|
|
set _WORKAREASIZE 0x4000
|
|
}
|
|
|
|
#jtag scan chain
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
set _CPUTAPID 0x4ba00477
|
|
}
|
|
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
|
|
|
|
# 16K is plenty, the smallest chip has this much
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
|
|
|
# JTAG speed should be <= F_CPU/6. F_CPU after reset is 4 MHz, so use F_JTAG = 0.5MHz
|
|
#
|
|
# Since we may be running of an RC oscilator, we crank down the speed a
|
|
# bit more to be on the safe side. Perhaps superstition, but if are
|
|
# running off a crystal, we can run closer to the limit. Note
|
|
# that there can be a pretty wide band where things are more or less stable.
|
|
|
|
adapter_khz 500
|
|
|
|
adapter_nsrst_delay 100
|
|
if {[using_jtag]} {
|
|
jtag_ntrst_delay 100
|
|
}
|
|
|
|
if {![using_hla]} {
|
|
# if srst is not fitted use SYSRESETREQ to
|
|
# perform a soft reset
|
|
cortex_m reset_config sysresetreq
|
|
}
|