e44539d66c
- write speed up to 150 kByte/s on STM32F469I-disco (due to SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in dual 4-line mode or STM32H73BI-Disco in octal mode - tested with STM32L476G-disco (64MBit flash, 3-byte addr), STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and STM32L476G-Disco (all 128Mbit flash, 3-byte addr), STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr) STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr) STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr) STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr) - suitable cfg for Discovery boards included - limited parsing of SFDP data if flash device not hardcoded (tested only in single/quad mode as most devices either don't support SFDP at all or have empty(!) SFDP memory) - 'set' command for auto detection override (e. g. for EEPROMs) - 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.) - makefile for creation of binary loader files - tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg - tcl/board/stm32f7discovery.cfg removed as name is ambiguous (superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg) - dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI with two W25Q128FV, sample cfg files included and on STM32H745I-Disco, STM32H747I-Disco, STM32H750B-Disco - read/verify/erase_check uses indirect read mode to work around silicon bug in H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last bytes causes debug interface to hang) - octospi supported only in single/dual 1-line, 2-line, 4-line and single 8-line modes, (not in hyper flash mode) Requirements: GPIOs must be initialized appropriately, and SPI flash chip be configured appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip specific, cf. included cfg files. The driver infers most parameters from current setting in CR, CCR, ... registers. Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8 Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com> Reviewed-on: http://openocd.zylin.com/4321 Tested-by: jenkins Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Reviewed-by: Christopher Head <chead@zaber.com>
46 lines
1.3 KiB
INI
46 lines
1.3 KiB
INI
# This is a stm32h745i-disco with a single STM32H745XIH6 chip.
|
|
# www.st.com/en/product/stm32h745i-disco.html
|
|
#
|
|
|
|
# This is for using the onboard STLINK
|
|
source [find interface/stlink.cfg]
|
|
|
|
transport select hla_swd
|
|
|
|
set CHIPNAME stm32h745xih6
|
|
|
|
# enable stmqspi
|
|
if {![info exists QUADSPI]} {
|
|
set QUADSPI 1
|
|
}
|
|
|
|
source [find target/stm32h7x_dual_bank.cfg]
|
|
|
|
source [find board/stm32h7x_dual_qspi.cfg]
|
|
|
|
$_CHIPNAME.cpu0 configure -event reset-init {
|
|
global QUADSPI
|
|
|
|
mmw 0x52002000 0x00000004 0x0000000B ;# FLASH_ACR: 4 WS for 192 MHZ HCLK
|
|
|
|
mmw 0x58024400 0x00000001 0x00000018 ;# RCC_CR: HSIDIV=1, HSI on
|
|
mmw 0x58024410 0x10000000 0xEE000007 ;# RCC_CFGR: MCO2=system, MCO2PRE=8, HSI as system clock
|
|
mww 0x58024418 0x00000040 ;# RCC_D1CFGR: D1CPRE=1, D1PPRE=2, HPRE=1
|
|
mww 0x5802441C 0x00000440 ;# RCC_D2CFGR: D2PPRE2=2, D2PPRE1=2
|
|
mww 0x58024420 0x00000040 ;# RCC_D3CFGR: D3PPRE=2
|
|
mww 0x58024428 0x00000040 ;# RCC_PPLCKSELR: DIVM3=0, DIVM2=0, DIVM1=4, PLLSRC=HSI
|
|
mmw 0x5802442C 0x0001000C 0x00000002 ;# RCC_PLLCFGR: PLL1RGE=8MHz to 16MHz, PLL1VCOSEL=wide
|
|
mww 0x58024430 0x01070217 ;# RCC_PLL1DIVR: 192 MHz: DIVR1=2, DIVQ=8, DIVP1=2, DIVN1=24
|
|
mmw 0x58024400 0x01000000 0 ;# RCC_CR: PLL1ON=1
|
|
sleep 1
|
|
mmw 0x58024410 0x00000003 0 ;# RCC_CFGR: PLL1 as system clock
|
|
sleep 1
|
|
|
|
adapter speed 24000
|
|
|
|
if { $QUADSPI } {
|
|
qspi_init 1
|
|
}
|
|
}
|
|
|