1c021ed0af
Remove this underutilized feature. Despite the fact that a lot of configs specifies a arbitrary "variant", only the xscale target actually defines any. In the case of xscale, the use of -variant is dubious since 1) it's used as a redundant irlen specifier, 2) it carries a comment that it doesn't really need it and 3) only two xscale configs even specify it. If there's a future target that needs a variant set, a target specific option could be added when needed. Change-Id: I1ba25a946f0d80872cbd96ddcc48f92695c4ae20 Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com> Reviewed-on: http://openocd.zylin.com/2283 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
72 lines
1.9 KiB
INI
72 lines
1.9 KiB
INI
# script for str9
|
|
|
|
if { [info exists CHIPNAME] } {
|
|
set _CHIPNAME $CHIPNAME
|
|
} else {
|
|
set _CHIPNAME str912
|
|
}
|
|
|
|
if { [info exists ENDIAN] } {
|
|
set _ENDIAN $ENDIAN
|
|
} else {
|
|
set _ENDIAN little
|
|
}
|
|
|
|
# jtag speed. We need to stick to 16kHz until we've finished reset.
|
|
adapter_khz 16
|
|
|
|
adapter_nsrst_delay 100
|
|
jtag_ntrst_delay 100
|
|
|
|
#use combined on interfaces or targets that can't set TRST/SRST separately
|
|
reset_config trst_and_srst
|
|
|
|
if { [info exists FLASHTAPID] } {
|
|
set _FLASHTAPID $FLASHTAPID
|
|
} else {
|
|
set _FLASHTAPID 0x04570041
|
|
}
|
|
jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID
|
|
|
|
if { [info exists CPUTAPID] } {
|
|
set _CPUTAPID $CPUTAPID
|
|
} else {
|
|
set _CPUTAPID 0x25966041
|
|
}
|
|
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
|
|
|
|
|
if { [info exists BSTAPID] } {
|
|
set _BSTAPID $BSTAPID
|
|
} else {
|
|
# possible values: 0x1457f041, 0x2457f041
|
|
# we ignore version in check below
|
|
set _BSTAPID 0x1457f041
|
|
}
|
|
jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID -ignore-version
|
|
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
|
target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME
|
|
|
|
$_TARGETNAME configure -event reset-start { adapter_khz 16 }
|
|
|
|
$_TARGETNAME configure -event reset-init {
|
|
# We can increase speed now that we know the target is halted.
|
|
#adapter_khz 3000
|
|
|
|
# -- Enable 96K RAM
|
|
# PFQBC enabled / DTCM & AHB wait-states disabled
|
|
mww 0x5C002034 0x0191
|
|
|
|
str9x flash_config 0 4 2 0 0x80000
|
|
flash protect 0 0 7 off
|
|
}
|
|
|
|
$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384 -work-area-backup 0
|
|
|
|
#flash bank str9x <base> <size> 0 0 <target#> <variant>
|
|
set _FLASHNAME $_CHIPNAME.flash0
|
|
flash bank $_FLASHNAME str9x 0x00000000 0x00080000 0 0 $_TARGETNAME
|
|
set _FLASHNAME $_CHIPNAME.flash1
|
|
flash bank $_FLASHNAME str9x 0x00080000 0x00008000 0 0 $_TARGETNAME
|