Commit Graph

42 Commits

Author SHA1 Message Date
Tom Rini
db04ff42c7 mtd: Make CONFIG_MTD be the gate symbol for the menu
The help for CONFIG_MTD explains that it needs to be enabled for various
things like NAND, etc to be available. It however then doesn't enforce
this dependency and so if you have none of these systems present you
still need to disable a number of options. Fix this by making places
that select/imply one type of flash, but did not do the same, also do
this for "MTD". Make boards which hadn't been enabling MTD already but
need it now, do so. In a few places, disable CONFIG_CMD_MTDPARTS as it
wasn't previously enabled but was now being implied.

Signed-off-by: Tom Rini <trini@konsulko.com>
2024-01-22 14:18:54 -05:00
Andre Przywara
5ad98c57b8 sunxi: remove CONFIG_MACPWR
The CONFIG_MACPWR Kconfig symbol is used to point to a GPIO that enables
the power for the Ethernet "MAC" (mostly PHY, really).
In the DT this is described with the phy-supply property in the MAC DT
node, pointing to a (GPIO controlled) regulator. Since we need Ethernet
only in U-Boot proper, and use a DM driver there, we should use the DT
instead of hardcoding this.

Add code to the sun8i_emac and sunxi_emac drivers to check the DT for
that regulator and enable it, at probe time. Then drop the current code
from board.c, which was doing that job before.
This allows us to remove the MACPWR Kconfig definition and the respective
values from the defconfigs.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
2023-10-22 23:40:56 +01:00
Andre Przywara
b072aefbbe sunxi: define SYS_MONITOR_LEN in Kconfig, not _defconfig
Commit 08574ed339 ("Convert CONFIG_SYS_MONITOR_LEN to Kconfig") moved
the definition of said config variable from the common sunxi header to
*every board's* defconfig.
This is a platform choice, not board specific, so remove the variable
from there, instead set the one value for all Allwinner boards in
Kconfig.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
2022-12-13 20:33:31 +00:00
Tom Rini
08574ed339 Convert CONFIG_SYS_MONITOR_LEN to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_MONITOR_LEN

To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-11-10 10:08:55 -05:00
Andre Przywara
8094a4ed9d sunxi: defconfig: drop redundant definitions
When some configuration symbols were converted from header files to
Kconfig, their values were placed into *every* defconfig file.
Since we now have sensible per-SoC defaults defined in Kconfig, those
values are now redundant, and can just be removed.
This affects CONFIG_SPL_STACK, CONFIG_SYS_PBSIZE, CONFIG_SPL_MAX_SIZE,
and CONFIG_SYS_BOOTM_LEN.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-10-18 08:18:41 +01:00
Tom Rini
c45568cc4e Convert CONFIG_SYS_BOOTM_LEN to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_BOOTM_LEN

As part of this, rework error handling in boot/bootm.c so that we pass
the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not
be available to host tools but we do know the size that we passed to
malloc().

Cc: Soeren Moch <smoch@web.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-07 14:01:09 -04:00
Tom Rini
f113d7d303 Convert CONFIG_SPL_STACK to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_STACK

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:27 -04:00
Tom Rini
d0ee7f295d Convert CONFIG_SYS_PBSIZE to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_PBSIZE

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:00 -04:00
Andre Przywara
280294c5df sunxi: boards: Enable SPI flash support in U-Boot proper
Some sunxi boards ship with SPI flash, which allows booting through the
BootROM. We cover this functionality by a separate SPL "mini" driver.
Separately we have a proper DM_SPI driver for U-Boot proper, which
provides access to the SPI flash through the "sf" command. That allows
to update the firmware on the SPI flash, also to store the environment
there.

However only very few boards actually enable support for U-Boot proper,
even though that would work and the SPL part is configured.

Use the cleaned up configuration scheme to enable SPI flash on those
boards which mention a SPI flash in their .dts, or which use the SPL SPI
support.

Out of the box this would enable storing the environment on the SPI
flash, and allows people to read or write the flash from U-Boot, for
instance to update the SPI flash when booted via an SD card.

For this to actually work there must be a "spi0" alias in the DT, which
most boards are missing. But this should be addressed separately.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2022-03-10 17:34:44 +05:30
Tom Rini
55dabcc8f2 Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACY
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig.  Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL.  Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support.  Convert all of the existing users to
one or more symbols.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30 14:10:07 -04:00
Tom Rini
2656145224 Convert CONFIG_SYS_I2C_MVTWSI to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_I2C_MVTWSI

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30 14:10:06 -04:00
Simon Glass
975e7cf301 i2c: Rename SPL/TPL_I2C_SUPPORT to I2C
Rename these options so that CONFIG_IS_ENABLED can be used with them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-28 14:29:37 -04:00
Jernej Skrabec
8e6eed5748 configs: OrangePi PC2: Update defaults
OrangePi PC2 board has DRAM with ODT, so enable it.
H5 SoC is also connected to voltage regulator. It's default value is
reasonable at reset, but might be too low when rebooting with a lower
voltage programmed. In order to avoid instability, enable driver for it
and set it to appropriate voltage.

Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
[Andre: remove original ZQ value change, adjust commit message]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-07-10 01:22:09 +01:00
Tom Rini
2bba78076b configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-06-28 10:17:29 -04:00
Tom Rini
f7d0ae9c63 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28 08:46:52 -04:00
Andre Przywara
cd27b933f5 sunxi: Remove no longer needed default options from defconfigs
Now that those common Allwinner config symbols are defined automatically
for all boards in their Kconfig files, we can remove the now redundant
definitions from the boards' _defconfig files.

Some boards had a differing definiton for some of those symbols, it
looks like mostly to "merge races" when the symbol was introduced (new
board *_defconfig file missed the "add symbol to all files" patch).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-03-18 18:25:11 +05:30
Andre Przywara
671d64fe35 sunxi: move CONFIG_SYS_SPI_U_BOOT_OFFS out of defconfig
For Allwinner SoCs the CONFIG_SYS_SPI_U_BOOT_OFFS value is not really a
board choice: The boot ROM only loads the SPL from offset 0 of the SPI
NOR flash, and loads at most 32KB. This is a similar situation as on MMC,
so consequently we create our "joint" image (SPL + U-Boot proper) with
that 32KB offset during the build.

So define the value of this symbol to be 32KB by default for every
Allwinner SoC. This removes the definition of this symbol from the
_defconfig files, and avoids every board to define this over and over
again.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-24 23:06:56 +05:30
Tom Rini
0cfccb5401 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04 17:18:38 -05:00
Tom Rini
8d8ee47e03 env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-20 12:24:50 -05:00
Hannes Schmelzer
1ee774d209 Convert CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_SPI_U_BOOT_OFFS

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
[trini: Expose this for SPL_SPI_SUNXI for now]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25 20:59:00 -04:00
Simon Glass
37304aaf60 Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig
This converts the following to Kconfig:
   CONFIG_USE_PREBOOT
   CONFIG_PREBOOT

Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.

Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-02 11:19:14 -04:00
Andre Przywara
9340d8fe8b sunxi: move CONFIG_SPL_TEXT_BASE from *_defconfig to Kconfig
The choice of the SPL_TEXT_BASE is not really a decision that should be
specified by each board's defconfig, as this setting is actually
dictated by the SoC's memory map and the BootROM behaviour.

To make this obvious and reduce the clutter in the defconfig files,
let's specify the SoC constraints in the Kconfig stanza.
This allows us to remove these lines from the defconfig files again.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-15 12:25:32 +05:30
Simon Goldschmidt
f89d6133ee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Tom Rini
d168bcb6fe configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Paul Kocialkowski
9d0f9e8374 arm: sunxi: Enable DRAM ODT by default on H3/H5
Most of the boards we support with H3/H5 enable DRAM on-die termination,
which is consistent with the high DRAM clocks that are used.

Make it the default (like it's done for other similar platforms) instead
of defining it in each defconfig.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-04-10 15:34:32 +05:30
Tom Rini
7ae2729401 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-02-07 14:53:03 -05:00
Jagan Teki
29d280c88a sunxi: usb: Switch to Generic host controllers
Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.

So switch sunxi USB use EHCI and OHCI Generic controllers.

Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-01-18 22:19:09 +05:30
Tom Rini
8c5cad05c9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03 15:26:12 -04:00
Tom Rini
86cf1c8285 configs: Migrate CONFIG_NR_DRAM_BANKS
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 16:45:02 -04:00
Jagan Teki
937ddf2cdc configs: orangepi-pc2: Enable USB OTG peripheral mode
Enable USB_MUSB_GADGET which operate OTG in peripheral mode

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Alexander Graf
4f67b93fb7 part: Disable CONFIG_SPL_ISO_PARTITION by default
We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
could load distro images that usually get shipped as iso images. These images
usually come with a board agnostic boot environment.

However, there is very little point in having ISO support enabled (for anyone
really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
is board specific. So the fact that we enable ISO support in U-Boot proper does
not mean at all that we want ISO support in U-Boot SPL.

Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
all those default configs that disabled SPL ISO support.

Signed-off-by: Alexander Graf <agraf@suse.de>
2018-04-16 18:45:35 -04:00
Tom Rini
c9542eae0b configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-07 20:37:13 -04:00
Andre Przywara
341c058654 sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigs
Commit 278b90ce78 ("configs: Migrate CONFIG_SYS_TEXT_BASE") made
CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence
of moving the common definition shared by almost every sunxi board
into 123 individual defconfig files. But the U-Boot start address
for Allwinner boards is a platform decision which has been around for
ages, so defining it in each *board* config file seems a bit over the
top.
Define the standard values (160MB into DRAM for most SoCs, with two
SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from
the individual defconfigs.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-14 10:45:37 +05:30
Tom Rini
278b90ce78 configs: Migrate CONFIG_SYS_TEXT_BASE
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-11 09:30:09 -05:00
Tuomas Tynkkynen
a4fa811463 cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA
cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

 # CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-05 20:58:11 -05:00
Andre Przywara
a722359de4 SPL: SPI: select SPL_SPI_FLASH_SUPPORT on SPL_SPI_SUNXI
The Allwinner SPI flash SPL boot support is guarded by the SPL_SPI_SUNXI
symbol. But despite its generic name, the actual only use case for this
is to provide SPI flash support to the SPL, which requires
CONFIG_SPL_SPI_FLASH_SUPPORT to be defined.
Select this symbol from the SPL_SPI_SUNXI Kconfig definition. This
avoids doing this explicitly in the defconfig, and fixes SPI booting on
the Pine64 SoPine (and -LTS version) and the OrangePi Win board (both with
SPI flash).

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-25 10:05:05 +02:00
Tuomas Tynkkynen
ad12dc1844 cmd: Toggle the default value of CONFIG_CMD_IMLS
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
   i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-10 17:51:04 -04:00
Tom Rini
ecad7051b0 configs: Migrate all of the existing USB symbols, except fastboot
This syncs all of the currently Kconfig'd symbols out of the headers and
into the defconfig files.  This has two exceptions, first am335x_evm
needs to be converted to DM in SPL and then it can stop undef'ing
CONFIG_DM_USB.  Leaving this as-is results in a build failure, and
without work, run time failure.  The other case is am43xx_evm.h and in
turn am43xx_evm_usbhost_boot.  The problem here is that we need DWC3 USB
host mode in SPL, but still desire to have gadget mode in U-Boot proper.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-01 16:18:20 -04:00
Icenowy Zheng
a8df97d0da sunxi: add MACPWR in Orange Pi PC2 defconfig
The Ethernet function is enabled in the Orange Pi PC2 device tree and
defconfig, however, CONFIG_MACPWR is not properly set, which left the
PHY being disabled when booting, which makes the Ethernet function not
usable.

Add the proper value of this option in the PC2 defconfig.

Fixes: e7bd15ea15 ("sunxi: Add OrangePi PC 2 initial support")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-08-11 15:53:27 +05:30
Tom Rini
fb82fe3851 configs: Resync defconfigs
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-19 09:47:40 -04:00
Tom Rini
2681e78a5e configs: Re-sync
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-01 11:44:12 -04:00
Andre Przywara
e7bd15ea15 sunxi: Add OrangePi PC 2 initial support
The OrangePi PC 2 is a typical SBC with the 64-bit Allwinner H5 SoC.
Add a (64-bit only) defconfig defining the required options to build
the U-Boot proper.

Create a new .dts file for it by including the (32-bit) H3 SoC .dtsi
and changing the differing components accordingly.
This is a preliminary device tree mostly for U-Boot's own sake, it
is expected to be updated once the official DT gets accepted upstream.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[squash the commits, update the commit message]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30