red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The blue led is used to indicate U-Boot entering / exit indication
then Linux heartbeat.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use led node's name instead for
u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Add compatible = "gpio-leds" which is not present in kernel DT.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use blue led node's name instead
for u-boot,boot-led property.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use red led node's name instead
for u-boot,error-led property.
Rename red led node's name to led-red.
Remove status property which is useless.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Instead of using "st,fastboot-gpios" and "st,stm32prog-gpios", declare
2 gpio-keys.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use blue led node's name instead
for u-boot,boot-led property.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
As indicated in kernel led dt-bindings, label is a deprecated
property, so remove it and use red led node's name instead
for u-boot,error-led property.
Rename "red" led node's name to "led-red".
Remove status property which is useless.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
red led and button dedicated to fastboot share the same gpio GPIOA13.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from red led node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Instead of using "st,fastboot-gpios" and "st,stm32prog-gpios", declare
2 gpio-keys.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove "color" property from led-red node which is not supported
by U-Boot.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
led-red and button dedicated to fastboot share the same gpio GPIOA13.
led-blue and button dedicated to stm32prog share the same gpio GPIOA14.
Led driver is probed early so the corresponding gpio is taken and
configured in output which forbid fastboot and stm32prog button usage.
To avoid this, remove the "default-state" property from led-red and
led-blue led's node.
This will avoid to trigger the led driver probe() to configure the led
default state during startup.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Instead of using gpio directly to detect key pressed on button
dedicated for fastboot and stm32mprog, make usage of BUTTON UCLASS.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable BUTTON_GPIO flag for STM32MP15.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Enable BUTTON_GPIO flag for STM32MP15.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable BUTTON_GPIO flag for STM32MP15.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable BUTTON_GPIO flag for STM32MP15.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
When building with AARCH64 defconfig, we got warnings, fix them.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Fix flash@0 partition node name with correct offset.
Fixes: 90f992e6a5 ("arm: dts: stm32: Add partitions in flash0 and nand
node for stm32mp15xx-dhcom/dhcor")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Fix flash@0 partition node name with correct offset.
Fixes: 90f992e6a5 ("arm: dts: stm32: Add partitions in flash0 and nand node for
stm32mp15xx-dhcom/dhcor")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Fix flash@0 and nand@0 partition node name with correct offset.
Fixes: e91d3c6176 ("arm: dts: stm32: Add partitions in flash0 and nand
node for stm32mp15xx-ev1")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In case of an OTP-CLOSED STM32MP15xx system, the CPU core 1 cannot be
released from endless loop in BootROM only by populating TAMP BKPxR 4
and 5 with magic and branch address and sending SGI0 interrupt from
core 0 to core 1 twice. TAMP_SMCR BKP..PROT fields must be initialized
as well to release the core 1 from endless loop during the second SGI0
handling on core 1. Initialize TAMP_SMCR to protect the first 32 backup
registers, the ones which contain the core 1 magic, branch address and
boot information.
This requirement seems to be undocumented, therefore it was necessary
to trace and analyze the STM32MP15xx BootROM using OpenOCD and objdump.
Ultimately, it turns out that a certain BootROM function reads out the
TAMP_SMCR register and tests whether the BKP..PROT fields are non-zero.
If they are zero, the BootROM code again waits for SGI0 using WFI, else
the execution moves forward until it reaches handoff to the TAMP BKPxR 5
branch address.
This fixes CPU core 1 release using U-Boot PSCI implementation on an
OTP-CLOSED system, i.e. system with fuse 0 bit 6 set.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
SoC revision is only accessible via DBUMCU IDC register,
which requires BSEC.DENABLE DBGSWENABLE bit to be set to
make the register accessible, otherwise an access to the
register triggers bus fault. As BSEC.DBGSWENABLE is zero
in case of an OTP-CLOSED system, do NOT set DBGSWENABLE
bit as this might open a brief window for timing attacks.
Instead, report that this system is OTP-CLOSED and do not
report any SoC revision to avoid confusing users. Use an
SEC/C abbreviation to avoid growing SOC_NAME_SIZE .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The source file is in arch/arm/mach-stm32mp/ecdsa_romapi.c and not
in arch/arm/mach-stm32mp/stm32mp1/ecdsa_romapi.c . There are two
Makefile entries in each subdirectory. Drop the bogus one and keep
only the correct one, the one in arch/arm/mach-stm32mp/Makefile .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In case the system has resumed successfully, the PSCI suspend resume
code has to jump to the 'ep' successful resume entry point code path,
otherwise the code has to jump to content of the LR register, which
points to failed resume code path.
To implement this distinction, rewrite LR register stored on stack
with 'ep' value in case of a successful resume, which is really in
every case unless some catastrophic failure occurred during suspend.
Without this change, Linux counts every resume as failed in
/sys/power/suspend_stats/fail
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The "st,ext-phyclk" property is a unification of "st,eth-clk-sel"
and "st,eth-ref-clk-sel" properties. All three properties define
ETH CK clock direction, however:
- "st,eth-clk-sel" selects clock direction for GMII/RGMII mode
- "st,eth-ref-clk-sel" selects clock direction for RMII mode
- "st,ext-phyclk" selects clock direction for all RMII/GMII/RGMII modes
The "st,ext-phyclk" is the preferrable property to use.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Manage 2 ethernet instances, select which instance to configure with mask
If mask is not present in DT, it is stm32mp15 platform.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Marek Vasut <marex@denx.de> # Rework the code
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Use const bool for the values parsed out of DT. Drop the duplicate
assignment of false into those bool variables, assign them directly
with the content parsed out of DT. Abbreviate the variable name too.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Use dev_*() only to print all the logs from this glue code,
instead of mixing dev_*(), log_*(), pr_*() all in one code.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Move the log_debug() calls on top of the bit manipulation code.
No functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Use FIELD_PREP to configure content of ETH_SEL bitfield in SYSCFG_PMCSETR
register. No functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Replace ifdef CONFIG_CLK with if (CONFIG_IS_ENABLED(CLK)) to improve code
build coverage. Some of the functions printed debug("%s: OK\n", __func__);
on exit with and without CLK enabled, some did not, make it consistent and
print nothing if CLK is disabled.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Move board_interface_eth_init() into eqos_probe_syscfg_stm32() in STM32
driver glue code. The eqos_probe_syscfg_stm32() parses STM32 specific DT
properties of this MAC and configures SYSCFG registers accordingly, there
is nothing board specific happening in this function, move it into generic
driver code instead. Drop the now unused duplicates from board files.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The current glue code is specific to STM32MP15xx, the upcoming STM32MP13xx
will introduce another entry specific to the STM32MP13xx. Rename the current
entry to eqos_stm32mp15_config in preparation for STM32MP13xx addition. No
functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
Move STM32 glue code into separate file to contain the STM32 specific
code outside of the DWMAC core code. No functional change.
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER<christophe.roullier@foss.st.com>
FMC2 IP supports up to 4 chip select. On MP1 SoC, only 2 of them are
available when on MP25 SoC, the 4 chip select are available.
Let's use a platform data structure for parameters that will differ.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The FMC2 revision 2 supports security and isolation compliant with
the Resource Isolation Framework (RIF). From RIF point of view,
the FMC2 is composed of several independent resources, listed below,
which can be assigned to different security and compartment domains:
- 0: Common FMC_CFGR register.
- 1: EBI controller for Chip Select 1.
- 2: EBI controller for Chip Select 2.
- 3: EBI controller for Chip Select 3.
- 4: EBI controller for Chip Select 4.
- 5: NAND controller.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the support of the revision 2 of FMC2 IP.
- PCSCNTR register has been removed,
- CFGR register has been added,
- the bit used to enable the IP has moved from BCR1 to CFGR,
- the timeout for CEx deassertion has moved from PCSCNTR to BCRx,
- the continuous clock enable has moved from BCR1 to CFGR,
- the clk divide ratio has moved from BCR1 to CFGR.
The MP1 SoCs have only one signal to manage all the controllers (NWAIT).
The MP25 SOC has one RNB signal for the NAND controller and one NWAIT
signal for the memory controller.
Let's use a platform data structure for parameters that will differ
between MP1 and MP25.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The OHCI HCD is mandatory for USB 1.1 FS/LS device support, enable it.
This used to be enabled implicitly before, now that implicit dependency
disappeared and this got disabled. Enable it manually.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch avoids compilation issue when CONFIG_USB_GADGET is deactivated
in defconfig, with undefined reference to run_usb_dnl_gadget and to
g_dnl_set_product.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This prints the MMC device being read similar to how we print the MMC
device we write to when e.g. calling saveenv.
One of the side effects is that the boot log now shows from which MMC
device the env was loaded:
Loading Environment from MMC... Reading from MMC(1)... OK
This is useful to identify which MMC device the environment was loaded
from for boards where there are more than one (e.g. eMMC and SD card)
without adding some debug messages manually.
Sadly, there's no way to know which of the default or redundant
environment is being read from env_mmc_load before env_import_redund is
called so it is printing a bit later (and possibly after error/warning
messages).
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
default n doesn't need to be specified. It is default option anyway.
Similar changes have been done by commit 18370f1497 ("Kconfig: Remove all
default n/no options").
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
