Windows socket descriptor is not file descriptor, so when
using remote_bitbang on Windows, it fails with "fdopen:
failed to open write stream".
This patch removes the file write stream, replaces it
with socket write calls.
Change-Id: Ifd7c8a4139a5ac51ecd2846835a7a947a90fe16c
Signed-off-by: Yun Liu <liuyun.97@gmail.com>
Reviewed-on: http://openocd.zylin.com/6096
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Some CMSIS-DAP adapters keep buffered packets over
USB close/open so we need to flush up to 64 old packets
to be sure all buffers are empty.
Flush just after cmsis_dap_open() and in the case of command mismatch.
Change-Id: If21a118639e64d90635b4ecf81013d29a7b9f78d
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6135
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Check returned HID report number (or the first byte of returned
bulk packet) which should be equal to the issued command or 0xff
in case of the command is not implemented.
Fix error return paths in cmsis_dap_init() to clean up the adapter
connection.
Don't fail cmsis_dap_init() when an unimportant function fails
(for the case the adapter doesn't implement some parts of protocol).
Change-Id: Ief8382aabe9915346b2273702fb2ff17bbb5eb1b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6121
Tested-by: jenkins
Reviewed-by: Peter Lawrence <majbthrd@gmail.com>
Now that all commands are executed through the common handler
command_unknown(), the message about command execution is logged
by command_unknown(). There is no need, for "native" commands
(.jim_handler) at root level to log the message (again) by itself.
Remove calls to script_debug() apart from command_unknown().
Make script_debug() static as only used in command.c.
Change-Id: I9b2728b69e7643d6121c4b35a96bc825bcb5488d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5676
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
While still keeping the tree of struct command, stop registering
commands in jim by the root "word" only.
Register the full-name of the command and pass as private data the
struct command of the command itself.
Still use the tree of struct command to un-register the commands.
Some "native" commands (.jim_handler) share the same handler, then
the handler checks the command name to run the right code.
Now argv[0] returns the full-name of the command, so check the
name by looking in the struct command passed as private data.
Change-Id: I5623c61cceee8a75f5d5a551ef3fbf5a303af6be
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5671
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Each one of CMSIS-DAP command handlers was responsible for setting
HID report number, which in case of USB bulk transport was not used
at all. The command had to be filled with 1 byte offset whereas
the response was read without an offset.
Introduce 'command' and 'response' pointers into struct cmsis_dap.
Use them for filling the command and read the response respectively.
CMSIS-DAP command parameter are now at positions as documented in
https://arm-software.github.io/CMSIS_5/DAP/html/group__DAP__Commands__gr.html
Adjust buffer allocation for HID and USB bulk transports.
While on it, use h_u32_to_le() and h_u16_to_le() instead of per-byte
writes.
Change-Id: Ib0808d6826ba0e254c1007ace8b743405536332a
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/6120
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The hidapi cmsis-dap backend is using a packet_size of
64+1: 64 is the bMaxPacketSize0 and 1 is the hid Report-Id.
In hidapi::hid_write(), the packet_size is decremented by 1 and
stored for the next transfer.
The packet_size is now valid bMaxPacketSize0=64,
so when hid_read() is called, libusb_bulk_transfer() finishes w/o timeout.
For the libusb bulk backend, the same packet_size of 64+1 is used,
but there's no hid_write() to decrement and store it for the next read.
So the next time a read is done, it will try to read 64+1 bytes.
Fix this by putting the packet logic within each backend.
Use calloc() to allocate the struct cmsis_dap to be on safer side.
Change-Id: I0c450adbc7674d5fcd8208dd23062d5cdd209efd
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/5920
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Now that the old drivers have been converted to libusb1, there is
no need to keep the build dependency from libusb0.
Drop libusb0 from configure and makefiles, remove the libusb0
helper and remove libusb0 and libusb-compat from the README files.
Change-Id: Icc05be74ae5971ba6cbb67d39107c709a4d826e6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5993
Tested-by: jenkins
Convert the driver from libusb0 to libusb1.
Change-Id: Idef0b6cf10fab583bc8d13b3b4fadd5cc368c090
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5990
Tested-by: jenkins
Convert the driver from libusb0 to libusb1.
Change-Id: I3f334f2d02515d612097955e714910a587169990
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5992
Tested-by: jenkins
In case of some error, the USB device and firmware file are still
claimed. Make sure refcounting is properly accounted for both cases.
Change-Id: I933114f68e59280e58372c0941a0062fe96ab340
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/6115
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If not, multiple instances of OOCD can concurrently use it.
Change-Id: I48cc9d90521d1dcc7720c6e8bec74f45972d16f7
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4589
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
With zy1000 removed, there is no other implementation that uses
the minidriver, apart from the test/example minidriver-dummy.
While the idea of the minidriver is probably still valid (that is
to intercept jtag primitives before serialization), there is no
current use case, no guarantee it is really working, and the way
it was implemented (by macros and #if conditionals) is really hard
to maintain and test.
Let's let it rip in git history, from where it could eventually be
taken back in a more modern implementation.
The entry points of minidriver API are still in the code with the
original names.
Change-Id: I882e32cb26cf5842f9cba14e3badaf8948e3760d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6091
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The code for zy1000 has been marked as deprecated in release
v0.10.0, 4 years ago.
Time to drop it!
Change-Id: I08fca2a2bf8f616f031e15fd37dac3197a40ba50
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6090
Tested-by: jenkins
Some command were already marked as deprecated in release v0.7.0,
more then 7 years ago, and for some of them the depredation date
is even earlier.
We can reasonably expect that in these 7 years any user of OpenOCD
has already migrated to v0.7.0 or to some following intermediate
build, thus has already updated any local/personal script to get
rid of the deprecated message.
Drop the commands already deprecated in v0.7.0.
Change-Id: I81cdc415ab855ebf30980ef5199f9780c5d7f932
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6085
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The buffer passed to stlink_usb_trace_read() is allocated of size
*size and does not need to be zero-terminated. There is no reason
to not fill its last byte.
When checking the bytes available on swo, limit the retrieved byte
length to *size.
Change-Id: Iade0f8963118695931f13a8a3f1ab204911236b6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/6061
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Missing the space cause the hex value to be printed together with
the following field.
Add a space after PRIx32.
Change-Id: I95824a9a8b8c0ad911d6c31f732d926cb3e0c068
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6060
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Remove all the old tpiu code and replace it with a wrapper that
uses the new commands, prints-out the new commands and informs
about the deprecation.
All the code that handles the deprecated tpiu commands is enclosed
between the comments
/* START_DEPRECATED_TPIU */
and
/* END_DEPRECATED_TPIU */
so will be easy to remove it in the future.
Change-Id: I70b0486770128203b923346382d9a90b8ec08439
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6030
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
The change [1] guarantees that the value pointed by 'prescaler'
gets always set, even when the adapter does not support the
specific mode requested (e.g. sync), or during trace disabling.
This works fine with the code in armv7m_trace_tpiu_config(), but
requires all the parameters to be valid also to disable the trace
(with 'enable==false'), otherwise returns error on incorrect
parameters or even causes segmentation fault if pointers
'trace_freq' or 'prescaler' are NULL.
Another problem in stlink_config_trace(), not linked with [1], is
caused by a tentative to change the settings on an already enabled
trace; the trace is disabled before the new parameters are fully
validated and in case of invalid parameters the trace is not
re-enabled.
It would be more logical to first check all the parameters, then
disable the trace, change the settings and re-enable the trace.
Practically revert [1] by checking 'enable==false' at function
entry, then disable trace and exit without any further check on
the other parameters.
For the case 'enable==true', validate all the function parameters
then disable the trace, update the trace settings and re-enable
the trace.
Modify the caller armv7m_trace_tpiu_config() to initialize the
variable 'prescaler' to a safe value to avoid the issue targeted
by [1].
[1] commit 38277fa752 ("jtag/drivers/stlink_usb: fix SWO prescaler")
Change-Id: Ia6530682162ca2c9f5ac64301f2456f70cc07ed2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5934
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Convert the driver from libusb0 to libusb1.
Change-Id: I17d14522db18b4050d462d23151ec97d3a315a7f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5991
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Quote: The ST-LINK TCP server is an application to share the debug
interface of a single ST-LINK board among several host applications,
typically a debugging tool and a monitoring tool.
Note: ST-Link TCP server does not support the SWIM transport.
ST-LINK TCP server allows several applications to connect to the same
ST-Link through sockets (TCP).
To use ST-LINK TCP server:
- using stlink-dap : use 'st-link backend tcp [port]'
- using hla : use 'hla_stlink_backend tcp [port]'
the default port value is 7184
Change-Id: I9b79f65267f04b1e978709934892160e65bd2d6d
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5633
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
the introduced stlink_backend_s struct provides an API to separate USB
internals from stlink core.
this separation aims to ease:
- stlink-server integration [1]
- stlink driver split into modules:
- stlink_core
- stlink_usb
- stlink_tcp [1]
[1] refer to http://openocd.zylin.com/#/c/5633/
Change-Id: Iff6790942612ce1769ec4c75990914534e5e9e24
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5632
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In case an USB location path contains path members
larger than 9. The string_length variable is regardless
decremented by 2 with assumption that the member is
one digit length. For exmaple 1-12.2 will fail.
This patch uses strlen to calculate
digits in a path member.
Change-Id: I9c26a04d0c6af13fec65157f222599497294e2b2
Signed-off-by: Krzysztof Hockuba <krzysztof@hockuba.eu>
Reviewed-on: http://openocd.zylin.com/6048
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
If user specifies a serial number for the jlink device, openocd
extends the search to network jlink devices too, without checking
if the host has a valid and functional network connection. If the
network is not functional, libjaylink returns error. This error
invalidates the discovery on USB, even if it was successful.
Factor-out parts of the jlink_init into separate jlink_open_device
function, use that function to firstly discover and match USB
devices and, if matching device was not found on the USB bus and
serial number was specified, repeat discovery and matching via TCP.
Fixes: https://sourceforge.net/p/openocd/tickets/294/
Change-Id: Iea0de1640d4e5b21ecc7e9c1dd6d36f214d647c2
Signed-off-by: Bohdan Tymkiv <bohdan200@gmail.com>
Reviewed-on: http://openocd.zylin.com/6025
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
When using the adapter olimex arm-jtag-swd (to convert to SWD a
JTAG-only FTDI adapter), the pin trst on JTAG side is re-used to
control the direction of pin SWDIO on SWD side.
There is a single reset API at adapter driver to assert/deassert
either srst and/or trst. A request to assert/deassert srst can
cause also trst to change value, hanging the SWD communication.
In SWD mode, ignore the value passed to trst.
Change-Id: I5fe1eed851177d405d77ae6079da9642dc1a08f1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6006
Tested-by: jenkins
Add to doxygen comment the missing parameters.
Remove from doxygen comment any non-existing parameter.
Fix the parameter names in doxygen comment to match the one in the
function prototype.
Where the parameter name in the doxygen description seems better
than the one in the code, change the code.
Escape the character '<' to prevent doxygen to interpret it as an
xml tag.
Change-Id: I22da723339ac7d7a7a64ac4c1cc4336e2416c2cc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6002
Tested-by: jenkins
Use '@param' in front of function's parameters and '@a' when the
parameter is recalled in the description.
This fixes doxygen complains:
warning: Found unknown command '@buff16'
While there, fix a minor typo s/occured/occurred/ in a comment and
the typo s/@apram/@param/ in a doxygen comment.
Change-Id: I5cd86a80adef552331310a21c55ec5d11354be21
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/6001
Tested-by: jenkins
This should provide greater compatibility with different OpenULINK
targets which might be using various endpoints numbers. Since they're
advertised in the USB descriptor anyway it makes sense to autodetect
them.
Interface is no longer claimed before attempting to load firmware to a
freshly booted device, so I have no idea if this will break on windows
or other uncommon systems (Paul).
Change-Id: Iee10dcb6911dcf46239c430e174d9f98b5bde3c2
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/2445
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Avoid multiple definition of cmsis_dap_usb_backend and
cmsis_dap_hid_backend using 'extern'.
Move the prototypes in cmsis_dap.h.
Remove the useless #if/#endif around the prototypes.
Change-Id: I8d73fe148e2155620244bc887d4235e9af530e30
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5790
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
http://openocd.zylin.com/4831 has following problems in selecting
USB device/interface to connect:
- attempts connection to any device with user class and 2 bulk endpoints
- regardless of cmsis_dap_vid_pid or cmsis_dap_serial setting
connects to the first suitable device
Distinguish between real match and no filtering cases and use that info
appropriately.
Add debug messages to show why the interface is refused.
Move CMSIS-DAP interface string detection before checking of class/endpoints
to give more understandable debug log in the case the device is refused.
Keep track of reliable matches in both device and interface enumeration.
First search for the interface with CMSIS-DAP in the interface string.
If it fails, chose the first suitable interface.
Change-Id: Ia1aacd5631a9f5c5db580bfb5745ceb6240d61ad
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5789
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
This change implements CMSIS-DAP v2 which works with raw USB bulk transfers.
The old driver is now split into a generic CMSIS part and a HID backend,
with a new raw USB backend for CMSIS-DAP v2.
New commands:
- cmsis_dap_backend (usb_bulk | hid | auto)
- cmsis_dap_usb interface <interface number>
Change-Id: I4218477b12ccbfe19c9b332321cd21394bf44e30
Signed-off-by: Mickaël Thomas <mickael9@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4831
Tested-by: jenkins
Old stlink firmware in stlink V1 and stlink V2 pre-J15 do not
handle FPU registers in the read_reg() and write_reg() API.
Add code to be compatible with the new API of OpenOCD.
Change-Id: Ib0439c5294b6911ea75efe8c7fa085b014317a4b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5883
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The API of hla have been defined from ST-Link basic operations.
By chance, all the current implementation of hla (st-link, ti-icdi
and nulink) share the same way to handle the parameter 'num' of
the API read_reg() and write_reg(), that is simply using it to
initialize the field REGSEL (bits [6:0]) of armv7m Debug Core
Register Selector Register (DCRSR).
Add a comment in the API definition to highlight this, in case it
get used by a further hla implementation, then rename as 'regsel'
the 'num' parameter.
Change-Id: I4b6a2c7d78b4fc4de2b9b2bdba065414b15c6ba3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5882
Reviewed-by: Edward Fewell <edwardfewell@hotmail.com>
Tested-by: jenkins
Reviewed-by: Zale Yu
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Use integer rounding for the computation of prescaler.
Improve the test of prescaler range, knowing its value would be
decremented before being written in TPIU ACPR.
Change-Id: I041dde1dca41323904e36a6b6975028a6de902b3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5909
Tested-by: jenkins
While stlink v2 anly accept till to 2 MHz for SWV baudrate, stlink
v3 accepts up to 24 MHz.
Check the stlink version and use the respective max value.
Change-Id: I911207a35983b6acf0b901059076dd31f70e6290
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Pawel <phryniszak@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/283/
Reviewed-on: http://openocd.zylin.com/5908
Tested-by: jenkins
The value stored in TPIU ACPR is the prescaler value decremented
by one. Thus, the test should verify that prescaler does not
exceed the maximum ACPR value plus one. Also, zero value is not
allowed for prescaler.
Change-Id: I1817f04f2a310b2f413bad726f0cb9dd6a4172e2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5907
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
Commit 462c012066 ("Add complete JTAG debug logging.") breaks
the build for minidriver, that is enabled either on zy1000 build
and on minidriver-dummy build. The check on BUILD_ZY1000 was added
to pass the auto-build in jenkins. While the build issue with
minidriver-dummy was known, as reported in the comment, it was not
addressed and got ignored for slightly more than one year.
Use the macro HAVE_JTAG_MINIDRIVER_H in place of BUILD_ZY1000 to
take in account both builds that require the minidriver.
Fix also the build in case configure enables the HLA drivers due
to autodetection of libusb. The HLA drivers would not be in the
build and the function transport_is_hla() would be missing.
Change-Id: I1d85c5fa247bf4a85aba29b233c0b573b46665bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5911
Tested-by: jenkins
While at it, fix some coding style issues.
Change-Id: Id521394d89e0bf787a6f812701c2cc0fe7e4e63f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5919
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I58c9f5557d4809db9ccc34d32182c3797f825da1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5896
Tested-by: jenkins
The new libftdi 1.5 (2020-07-07) changes some API, deprecating the
old ones. This cause a warning at compile time.
Detect in configure the version of libftdi.
Use the new API in the driver's code.
Add an helper include file 'libftdi_helper.h' that wraps the old
API for backward compatibility with old libftdi.
Change-Id: I7800fbebe17dd0ce62e55b3598d8c08be8875bb7
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/286/
Reviewed-on: http://openocd.zylin.com/5891
Tested-by: jenkins
Clang static analyzer reported:
Warning: line 196, column 3
Potential leak of memory pointed to by 'fields'
Free allocated memory pointed by 'fields' and fields[i].in_value
Change-Id: I0b3935d9a235544afc03e39a4648319047e65815
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5906
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
The xlnx_pcie_xvc_execute_stableclocks() function can and
should be static.
Change-Id: I45fb1363caee1f1762b0b1ac2c6bc1bb0153b15b
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-on: http://openocd.zylin.com/5889
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The config_trace function has an out-parameter for generating the
prescaler for the TPIU. The STLink implementation wasn't always writing
it, causing the tpiu command to load uninitialized stack memory (minus
one) into the TPIU's prescaler register when 'external' was requested.
This change ensures that the out-parameter (and the other one,
trace_freq, which hadn't caused any buggy behavior for me) are written
every time.
Signed-off-by: Cliff L. Biffle <cliff@oxide.computer>
Change-Id: I222975869b1aa49cc6b1963c79d5ea0f46522b8c
Reviewed-on: http://openocd.zylin.com/5656
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Used jtag_libusb_open from libusb_helper.h instead of
libusb_open_device_with_vid_pid to get device handle,
as well as managing context, i.e. similar to stlink_usb.
Direct calls to libusb1 are left in for the moment.
(When this Gerrit revision was originally created,
the jtag_libusb_ wrappers did not return error conditions.)
Tested w/ a TM4C123GXL board
Change-Id: I71e9a366356c125444d4813e58ddd9b6c6498bf0
Signed-off-by: John Pham <jhnphm@gmail.com>
Signed-off-by: Matthew Trescott <matthewtrescott@gmail.com>
Reviewed-on: http://openocd.zylin.com/2527
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
The prescaler computation should round at the nearest integer
value, not to the next integer value.
Change-Id: I957e0774421211f3c4ba4b312738b1c67b87c4a2
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 051e80812b ("drivers/jlink: fix calculate_swo_prescaler formula")
Reviewed-on: http://openocd.zylin.com/5846
Tested-by: jenkins
Reviewed-by: Adrian M Negreanu <adrian.negreanu@nxp.com>
This driver provides support for Cadence JTAG BFM
The "jtag_dpi" driver implements a JTAG driver acting as a client for the
SystemVerilog Direct Programming Interface (DPI) for JTAG devices.
DPI allows OpenOCD to connect to the JTAG interface of a hardware model
written in SystemVerilog, for example, on an emulation model of
target hardware.
Tested on Ampere emulation with Altra and Altra Max models
Change-Id: Iaef8ba5cc1398ee2c888f39a606e8cb592484625
Signed-off-by: Kevin Burke <kevinb@os.amperecomputing.com>
Signed-off-by: Daniel Goehring <dgoehrin@os.amperecomputing.com>
Reviewed-on: http://openocd.zylin.com/5573
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
a) TPIU_ACPR is defined as:
SWO_baudrate = TRACECLKIN/(TPIU_ACPR +1)
b) TPIU_ACPR is set by armv7m_trace_tpiu_config()
target_write_u32(target, TPIU_ACPR, Prescaler-1), so
TPIU_ACPR = Prescaler-1
Replacing TPIU_ACPR in a), we get:
SWO_baudrate = TRACECLKIN/Prescaler, so
c) Prescaler = TRACECLKIN/SWO_baudrate
The Prescaler calculated by calculate_swo_prescaler() is greater by 1:
Prescaler = TRACECLKIN/SWO_baudrate + 1
The second problem is that even in situations when
an exact baudrate match is possible,
the resulting TRACECLKIN/Prescaler already has a 3% deviation.
For example, TRACECLKIN=88000000, SWO_baudrate=500000,
calculate_swo_prescaler will return Prescaler=171.
The correct value should be Prescaler=176 (TPIU_ACPR=175).
Might be related to https://sourceforge.net/p/openocd/tickets/263/
Change-Id: Ib4d6df6e34685a9be4c2995cb500b2411c76e39b
Signed-off-by: Adrian Negreanu <adrian.negreanu@nxp.com>
Reviewed-on: http://openocd.zylin.com/5807
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Change split from http://openocd.zylin.com/5172/ to avoid
conflicts with other pending changes in gerrit.
Change-Id: Id3e21c92b3da7ddce7b00664280da2143c06f172
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5604
Tested-by: jenkins
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
Change-Id: I2938e333bd1eac5218bd67aefb9d8f373da017a8
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5810
Tested-by: jenkins
The usage string should contain only the command parameters.
OpenOCD will automatically prepend the command name to the usage
string while dumping the usage or help message.
Remove the repeated command name from the usage string.
Change-Id: If10a0f1c254aee302b9ca08958390b7f21cdb21b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5824
Tested-by: jenkins
The usage string should contain only the command parameters.
OpenOCD will automatically prepend the command name to the usage
string while dumping the usage or help message.
Remove the repeated command name from the usage string.
Change-Id: Idbc301b34fab19e221131d232577c1629568e6ea
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5823
Tested-by: jenkins
Modify the format strings to properly handle uint32_t data types.
Change the prototype of detect_swo_freq_and_prescaler() in
'jlink.c' to avoid an implicit cast in the caller function.
Change the type of the variable retlen in some functions in
'usb_blaster.c' to properly pass their pointer to the local read
and write functions.
Use the proper parser COMMAND_PARSE_NUMBER(u32, ...).
Change-Id: I5227dbce04ee59881f173724db90790b7b9cc7af
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5815
Tested-by: jenkins
In several cases the 'int' status value returned by libusb and by
aice internal functions is taken in a variable of type 'int32_t',
requiring an implicit (but trivial) cast.
This makes compulsory using 'PRId32' in the format strings that
print such 'int32_t' result and requires an additional implicit
conversion to return the 'int32_t' as 'int'.
Replace to type 'int' all the occurrences of 'int32_t result' and
fix accordingly the format strings.
Plus, all the size of aice commands are stored as int32_t const
variables with uppercase name, violating the coding style, and are
then passed as 'int' parameter to the read/write functions.
Replace the variables with C macros carrying an 'int' value.
While there, replace also a 'uint32_t' loop index with 'unsigned'
and fix the format string in the loop.
Change-Id: Ic57d58770f1af95f003b5a02fbcb7c926ec06fd1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5814
Tested-by: jenkins
All the HLA transports (hla_swd and hla_jtag) register the same
set of commands. Such commands are mainly aimed at handling JTAG
compatibility that is required for the transport hla_jtag only.
Split per transport the command registration and limit the
commands to only those required by the transport itself.
Replace the command "hla newtap" with the transport specific
"swd newdap" or "jtag newtap".
Deprecate the command "hla".
Change-Id: I79c78fa97b707482608516d3824151a4d07644c0
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4877
Tested-by: jenkins
A JTAG TAP for boundary scan should be added in the scan chain
through the command "jtag newtap".
In some TCL target script the boundary scan TAP is added through
the command "swj_newdap", command that is inappropriate in this
context because specific for arm adi-v5 SWJ-DP.
This situation was probably created to bypass the error with HLA
framework, caused by missing command "jtag newtap".
Add the command "jtag newtap" in HLA, by reusing the existing
code for command "hla newtap".
Fix the TCL target scripts to use the command "jtag newtap" for
the boundary scan TAPs.
The TCL script target/psoc6.cfg has no evident reference to HLA,
so the reason for using "swj_newdap" is less clear. Nevertheless
it uses the wrong command and, once HLA is fixed, there is no
reason to avoid fixing it too.
Change-Id: Ia92f8221430cf6f3d2c34294e22e5e18963bb88c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4873
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
While loading to flash with debug level at least 3,
OpenOCD tries to print the whole loaded bitstream.
This will be very-very-slow due to implementation of
conversion from buffer to string.
* fix condition on selected debug level in jtag/core.c
* replace slow buf_to_str function from helper/binarybuffer.c
with faster but_to_hex_str function
Change-Id: I3dc01d5846941ca80736f2ed12e3a54114d2b6dd
Signed-off-by: Samuel Obuch <sobuch@codasip.com>
Reviewed-on: http://openocd.zylin.com/5800
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Implementation largely taken from Nuvoton github
https://github.com/OpenNuvoton/OpenOCD-Nuvoton
Reset is still not fully compatible with OpenOCD framework.
Adapted to hidapi.
Change-Id: Ieb1791b1b7f0b444c15c9668f8f2bcf34975d48f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Reviewed-on: http://openocd.zylin.com/5720
Tested-by: jenkins
Reviewed-by: Saravanan Sekar <saravanan@linumiz.com>
Reviewed-by: Marc Schink <dev@zapb.de>
Add support for Nu-Link1 over usb hidapi and config file.
The original work is fetched from Nuvoton github.
Code cleanup, fix merge conflicts, compile and runtime issues.
Switch the code from libusb to hidapi, being the device HID based.
Add documentation.
Merge fixes for multi-word memory read.
Reset is not fully compatible with openocd framework; currently
the target is reset and then halt at openocd start.
Change-Id: I9738de4e26783ba462ea3e39ec32069fd5bb7d94
Signed-off-by: Zale Yu <cyyu@nuvoton.com>
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5635
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
This commit fixes support for the nEDBG CMSIS-DAP interface
which is used ie. on the Curiosity Nano SAMD21 board.
nEDBG, similarily to mEDBG, does not support 512 byte HID packets.
This patch adds its USB PID to the exclusion list to make sure that
we stick with the default 64 bytes.
Change-Id: I9010b0cf77c0b1347269a759b5d16ee5155abb16
Signed-off-by: Michal Potrzebicz <michal@elevendroids.com>
Reviewed-on: http://openocd.zylin.com/5756
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The blinking was implemented for JTAG only.
Extend it to SWD.
There is no error check on SWD exchange. Add a FIXME for further
fix.
Change-Id: I42a6708c54b1eefaf691e0fe09ca58c42b2764fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5771
Tested-by: jenkins
Bitbang interface allows having a LED on one of the GPIO.
Let also linuxgpiod driver to specify and use the LED connection.
Change-Id: Id3d8772ee1808b92354fd073ba3947bacd8253ef
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5770
Tested-by: jenkins
The adapter NXP LPC-Link2 is a USB composite device that provides
five interfaces; among three of them that are of HID class, only
one is cmsis-dap.
Accordingly to ticket 255, OpenOCD code is not opening the right
HID interface; then it fails to communicate with the cmsis-dap
while checking the adapter's info.
Unfortunately, hidapi does not provide any support for reading the
string descriptor of the interface, otherwise it would have been
trivial to look for the right cmsis-dap interface.
In fact the cmsis-dap specification reports:
The CMSIS-DAP Firmware can be also part of a USB composite
device. If this case, the HID Interface String must
contain the sub-string CMSIS-DAP.
This requirement is satisfied by the USB device descriptor of the
LPC-Link2 reported below, but cannot be used.
Add a quirk to let OpenOCD only accept interface number zero on a
LPC-Link2 device.
Bus 001 Device 050: ID 1fc9:0090 NXP Semiconductors
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 239 Miscellaneous Device
bDeviceSubClass 2
bDeviceProtocol 1 Interface Association
bMaxPacketSize0 64
idVendor 0x1fc9 NXP Semiconductors
idProduct 0x0090
bcdDevice 1.00
iManufacturer 1 NXP Semiconductors
iProduct 2 LPC-LINK2 CMSIS-DAP V5.224
iSerial 3 I3F4AABA
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x00ab
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 4 LPC-LINK2 CMSIS-DAP V5.224
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 35
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 4
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 4
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 4
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 7 LPC-LINK2 DATA PORT
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 35
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 1
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 1
bInterfaceCount 2
bFunctionClass 2 Communications
bFunctionSubClass 2 Abstract (modem)
bFunctionProtocol 0
iFunction 5 VCOM
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0
iInterface 5 VCOM
CDC Header:
bcdCDC 1.10
CDC Call Management:
bmCapabilities 0x01
call management
bDataInterface 2
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 1
bSlaveInterface 2
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 4
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 5 VCOM
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 6 LPCSIO
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.11
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 33
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 2
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 2
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Change-Id: Ib3d46f87743a2d35a266842cb356035d898d466e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Suggested-by: Masatoshi Tateishi <tateishim3@gmail.com>
Reported-by: Donald Bailey <donaldb@users.sourceforge.net>
Fixes: https://sourceforge.net/p/openocd/tickets/255/
Reviewed-on: http://openocd.zylin.com/5732
Tested-by: jenkins
The code in cmsis_dap_usb_open() already searches for the right
HID device that corresponds to the adapter. By calling hid_open()
it asks hidapi to re-search the adapter again based on the VID:PID
and the serial string of the adapter it has just found!
Apart from being a run-time overhead, this has an additional
drawback; there are USB adapters built as composite USB devices
that, beside the cmsis-dap HID interface, have other HID
interfaces for other purposes.
A typical example is the NXP LPC-Link2, that over the 5 interfaces
0) cmsis-dap (HID)
1) VCOM-CDC
2) VCOM-CDC
3) LPCSIO (HID)
4) LPC-LINK2 DATA PORT (HID)
has 3 of them of HID class.
The code in cmsis_dap_usb_open() could select the right interface
but then cannot propagate this information to hid_open().
Replace the call to hid_open() with hid_open_path(), passing as
parameter the "unique" path of the HID device already found.
Checking in hidapi source code, the implementation of hid_open()
consists in enumerating the HID devices, scan for the first one
matching VID:PID and serial number, and opening it by calling
hid_open_path(). This analysis highlights that using directly
hid_open_path() should not introduce any regression.
While applying these changes, move hid_init() before enumerating
the HID devices. This has no real consequences because the HID API
is marked as optional but, logically, it should be called before
any other HID API.
Change-Id: I77ec01dca64223ec597f21f188f363366d0049c6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Suggested-by: Masatoshi Tateishi <tateishim3@gmail.com>
Reviewed-on: http://openocd.zylin.com/5731
Tested-by: jenkins
The function perror() sends the output to stderr, but OpenOCD
cannot intercept such output to send it to the log.
Replace all occurrences of perror() with LOG_ERROR(), but keeping
the same output format of perror().
The replacement is done automatically through:
sed -i 's/perror("\([^":]*\)[: ]*")/LOG_ERROR("\1: %s", strerror(errno))/' src/jtag/drivers/*.c
Change-Id: I4c140bdb09235d56cfd8bef75da9b56fbe7c2aec
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5728
Tested-by: jenkins
New adapter driver for GPIO bitbanging over Linux GPIO descriptors
through the library libgpiod.
On Debian based distribution, the package libgpiod-dev is required
for build.
Change-Id: I1ce1a4f1ca79096d6d476b01b523c8c10f2cac07
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5559
Tested-by: jenkins
If the configuration file specifies both SWD and JTAG gpios, the
current code request all of them. In case of overlap a warning is
generated when the same gpio is released for the second time.
Require and release only the gpio needed by the specified
transport.
Change-Id: I41a0970980ceeb559afa98ab34cfe93dffed2e1c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5556
Tested-by: jenkins
The split in OpenOCD between SWD and JTAG has been already fully
implemented. The bitbang driver still keeps a single API write()
to drive the output lines.
Introduce a new SWD specific API swd_write().
Move the existing SWD bitbang drivers to the new API by extracting
the available conditional implementation.
Cleanup some function prototype.
Remove the now unused global swd_mode, handled implicitly.
Rename bitbang_exchange() as bitbang_swd_exchange() to track its
scope for SWD only.
Change-Id: Ie53080b941cb1ac7a34a1f80bad8bee4e304454d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5555
Tested-by: jenkins
The SWD framework already takes care of switching between JTAG and
SWD by calling driver's switch_seq() in swd_connect() and in
swd_quit(); there is no need for the driver to force the switch
again.
Remove the extra switch between jtag and swd.
Change-Id: I84de4bffb593374b96fce31951c6cc83f92d2578
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5554
Tested-by: jenkins
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types FUNCTION_ARGUMENTS -f {} \;
This patch also fixes an incorrect function prototype in zy1000.c.
ZY1000 minidriver implementation overrides the function
arm11_run_instr_data_to_core_noack_inner(), but the prototype is
not the same as in src/target/arm11_dbgtap.c and to avoid compile
error it was changed also the prototype of the called function
arm11_run_instr_data_to_core_noack_inner_default().
Change-Id: I476cda8cdb0e1e280795b3b43ca95c40d09e4a3d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5630
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The checkpatch script from Linux kernel v5.1 complains about using
space before comma, before semicolon and between function name and
open parenthesis.
Fix them!
Issue identified using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types SPACING -f {} \;
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: I1062051d7f97d59922847f5061c6d6811742d30e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5627
Tested-by: jenkins
Current hla driver supports two "layout": stlink and ti-icdi.
The configure script allows to independently enable/disable the
the two layout. But in reality by selecting only one of them the
whole hla driver is built, including both "layouts".
This is currently not a big issue because the dependencies of the
two layout are the same (libusb), so we are sure that selecting
one of them would permit to build both.
This is going to change with the merge of a third "layout" for
Nuvoton Nu-Link, because it would be based on hidapi.
We need, at least, to decouple the build of libusb and hidapi
"layouts". A full decouple of each "layout" is also welcome to
match the selection done during configure.
Introduce a new automake macro for each of the two "layout" and
use them to conditionally build the "layout" files.
Use the existing autoconf macros to conditionally compile the code
that depends by the "layout".
Change-Id: Ia20da7a260002a8d2af883425aa401b8920d3f36
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5719
Tested-by: jenkins
The Jim_SetResultFormatted() frees jim object earlier and the
Jim_FreeNewObj() does it second time. It breaks the memory heap.
To avoid it the Jim_IncrRefCount() + Jim_DecrRefCount() should be used
instead of the Jim_FreeNewObj() call.
Change-Id: Ifa5f38009b2d617624b5f27e916720888a3dbad9
Signed-off-by: Mikhail Rasputin <mikhail.godlike.rasputin@yandex.ru>
Reviewed-on: http://openocd.zylin.com/5724
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Add support for SWD debug to the Xilinx XVC/PCIe driver.
This is possible since the device is essentially a shift-register.
So doing SWD vs JTAG is a matter of wiring things correctly on the
RTL side (use TMS for SWDI, TDO for SWDO).
The clang static checker doesn't find any new problems with this change.
Change-Id: I3959e21440cd1036769e8e56a55e601d3e4aee9a
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-on: http://openocd.zylin.com/5447
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This update is for testing the upcoming 0.2.0 release.
Change-Id: I400b09eb3ead4306c83c7980c621124101aaef7e
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5723
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This fixes a regression introduced in "2dc88e1479f29ef0141b05bfcd907ad9a3e2d54c"
Change-Id: I04dc19ed30118a4c499b83732700b2ee0fdb67b6
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5610
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
If the function parse_u64() fails, we jump to return, thus leaking
the memory just allocated in 'v'.
Issue identified by clang.
Move earlier the call to parse_u64() and the associated test,
before memory allocation.
While there, fix a possible NULL pointer dereferencing in case the
calloc() fails, by testing for allocation failure.
Change-Id: I6a77ee17aceb282bbdfefe7cdafeba2e0e7012f1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5692
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
When jtag_libusb_open() fails to find the adapter, it returns
error but left libusb initialized causing memory leak of libusb
internal data.
Issue found with valgrind when no adapter or board is connected to
the host, e.g.
valgrind openocd -f board/st_nucleo_f4.cfg
Close the libusb operations if jtag_libusb_open() has to return
error.
Change-Id: Ieb2f110be15705dafe80c099e7d83c07056c2a41
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5701
Tested-by: jenkins
For jtag/drivers/bcm2835gpio dev_mem_fd has been updated within
bcm2835gpio_init with the add on of gpio to mem. This permits the
access to memory of GPIO without the need for root access.
For failed attempt, a fallback to original memory follows.
It should be noted that any printed error is relative to original
memory ("dev/mem").
Tested on EFM32GG12B390F board
Change-Id: I4540bdf62fb3b91a51221e277881adfae138dcc5
Signed-off-by: tscn92 <tscn@kamstrup.com>
Reviewed-on: http://openocd.zylin.com/5568
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
After commit 0840414f0e ("helper/command: do not replace new
commands with ocd_ prefix"), the command name is present in
argv[0], so there is no need to pass it directly. The current code
causes the command name to be logged twice, once explicitly and
then from the content of argv[0]:
openocd -c 'debug_level 3; echo hello; shutdown'
<snip>
Debug: 13 3 command.c:142 script_debug(): command - echo echo hello
<snip>
Debug: 16 4 command.c:142 script_debug(): command - shutdown shutdown
Remove the command name from the arguments of the function
script_debug().
Change-Id: I57860774f450ff717ee71ef9dc07590549a84319
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5660
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The new stlink firmware requires opening the AP before issuing
any operation.
In the current code we have a 'questionable' check about the core
model to set the TAR autoincrement, that is issued without opening
the AP, thus causing a STLINK_BAD_AP_ERROR.
Modify the AP open API to handle this case and open AP#0 before
the memory access to check the core model.
Change-Id: I576955b5094bd41d63ff1fbad7b4fd9433253321
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reported-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/5691
Tested-by: jenkins
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Firmware v2j28 introduces the API to open and close the AP, but
closing AP always returns error 0x1d (STLINK_BAD_AP_ERROR).
Ignore the error returned by the bogus firmware on closing AP.
Change-Id: I992ddbf7acb10f1d376ed8f781eeb3344605b85d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5683
Tested-by: jenkins
When the transport is not specified, OpenOCD uses the first listed
by the selected adapter driver.
The old HLA driver for stlink lists SWD as first. The new driver
dapdirect instead lists JTAG, making more difficult a fallback to
HLA when dapdirect is not available due to old stlink FW.
Plus, in case of JTAG wiring, SWD is still possible, while the
opposite is not.
Reorder the list of transports to grant the default to SWD.
Change-Id: Id9c529e921b148d5b352d4603a9028c2a5f15d83
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Suggested-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5538
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
No reason to keep longer this temporary hack.
Remove it by reverting the original commit.
Change-Id: I5c6dcdb1f4755b7dba4c03a5033913ef8db35e18
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5533
Tested-by: jenkins
Now that SWIM is not accessed through HLA anymore, decouple the
SWIM code and remove the conditional execution.
Fix the inconsistency of the return type for stlink_usb_state() in
case of SWIM (returns ERROR_OK while type is enum target_state)
introduced by commit 3de6b5f6e5 ("jtag/drivers/stlink_usb :
implemented and repaired SWIM support").
The code added by commit above in stlink_usb_state() is an hack to
reuse existing HLA API to perform a reconnect.
Move the SWIM specific code from stlink_usb_state() to a dedicated
stlink_swim_op_reconnect() that provides consistent data type.
Change-Id: I3fe175fef00b0735bea6139b057f217a080c9d38
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 3de6b5f6e5 ("jtag/drivers/stlink_usb : implemented and repaired SWIM support")
Reviewed-on: http://openocd.zylin.com/5532
Tested-by: jenkins
Thanks to API separation between SWIM and the other transports, we
can easily split the memory read/write for SWIM from the rest of
the code.
While there, use the macro STLINK_DATA_SIZE as size of data chunks
that can be read/write in SWIM. This was not implemented before.
Change-Id: I7d913c92539007e4d914480bacc0126a8f0e9705
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5531
Tested-by: jenkins
Add SWIM and STM8 to documentation and update TODO file.
Introduce transport "swim" and command "swim newtap".
Switch in swim.c from HLA API to the new SWIM API.
Implement in stlink driver the SWIM APIs as wrappers of existing
HLA functions.
Remove any SWIM related reference from HLA files.
Update stm8 config files and stlink-dap interface config file.
Change-Id: I2bb9f58d52900f6eb4df05f979f7ef11fd439c24
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5530
Tested-by: jenkins
SWIM transport only supports two adapter speeds:
- "low speed" equal to 363 kHz (8 MHz / 22)
- "high speed" equal to 800 kHz (8 MHz / 10)
Replace the previous convention that use "0" or "1" for "low" or
"high" speed with the effective speed in kHz.
Rework the implementation of stlink_speed_swim().
Set low speed in the stm8 config files, because only low speed is
permitted at debug connection; the previous code ignores the
initial value.
Change-Id: I2484c9419a2c554c59eb6b9216339393ab0b54f3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5529
Tested-by: jenkins
SWIM is implemented by (ab)using the HLA API. This was acceptable
when OpenOCD code did not provided a clear separation between
transports and related APIs. Still today SWIM in OpenOCD is only
supported by STLink, so the decision to re-use the HLA API was the
simpler way to implement it.
After commit efd1d64222 ("adapter: switch from struct
jtag_interface to adapter_driver") the transports API are better
split and SWIM can be implemented as a separate set of API. This
would open the possibility to extend OpenOCD for other adapters
that provide SWIM, e.g. versaloon, or through SPI emulation [1].
Introduce a new set of files swim.[ch] to handle the SWIM API.
Beside the API that almost match the transport low-level data
communication (system_reset, read_mem, write_mem), add a further
API reconnect. Today, inside HLA STLink code, the reconnect is
implemented by hacking the HLA API state(). Please notice that
due to this hack the return type is incorrect; stlink_usb_state()
returns ERROR_OK in SWIM mode, while its return type is enum
target_state. Ignore the type mismatch and still call the HLA API
state in the new SWIM API reconnect. Further commit will fix it.
[1] http://kuku.eu.org/?projects/stm8spi/stm8spi
Change-Id: I52018e1e2200cbd41af8e5031f7b35dc761b61d6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5528
Tested-by: jenkins
The transition of STM8/SWIM out of HLA will require a new struct
swim_ops in struct adapter_driver.
To simplify the development, make the HLA interface temporarily
accessible through the struct adapter_driver.
This commit will be reverted after the swim rework.
Change-Id: I1e4f370cf64641164d7bcaa22f75ac58c9240052
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5527
Tested-by: jenkins
In the driver's code it's widely used the enum hl_transports for
any check concerning the current transport, even for the non-hla
transport dapdirect.
The driver already provides a stlink specific enum stlink_mode
that can be used in place of the hla one.
Replace the hla enum with the stlink one allover the code.
Introduce a hla specific wrapper stlink_usb_hl_open() to cope with
the only API that requires the hla specific enum.
The overall behaviour is not changed, with exception for a debug
message in stlink_usb_open() than now prints the numeric value of
stlink enum in place of the numeric value of the corresponding hla
one.
This change prepares the road for moving SWIM transport out of hla
by removing any reference to the macro HL_TRANSPORT_SWIM from the
stlink driver.
Change-Id: Ieeea34f312245a94bfc1333087afdb8eb9f77139
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5526
Tested-by: jenkins
The re is no need to split a long string, apart for fitting the
predefined line width.
Join the consecutive string fragments.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types STRING_FRAGMENTS -f {} \;
Change-Id: I8de52d572b0e3d4788c1d4d2b0cf8f94c7f08409
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5625
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
For void functions, a return as last statement is useless.
Remove it.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types RETURN_VOID -f {} \;
Change-Id: Ie0616fe98623f30d2d7b04ac9517d669774092de
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5622
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Functions that have no parameters should use "void" as parameter
in the function declaration.
Issue identified and fixed by script checkpatch from Linux kernel
v5.1 using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types FUNCTION_WITHOUT_ARGS --fix-inplace -f {} \;
Change-Id: If104ac75b44e939ec86155ff7b5720f2e33c6b39
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5621
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Line continuation, adding a backslash as last char of the line, is
requested in multi-line macro definition, but is not necessary in
the rest of C code.
Remove it where present.
Identified by checkpatch script from Linux kernel v5.1 using the
command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types LINE_CONTINUATIONS -f {} \;
Change-Id: Id0c69e93456731717a7b290b16580e9f8ae741bc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5619
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like parenthesis.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command:
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types SIZEOF_PARENTHESIS --fix-inplace -f {} \;
Change-Id: I8adb325bdb0e13211f8bae8b4770ec1979c176bf
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5618
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
In a switch/case statement, a break placed after a goto or return
is never executed.
The script checkpatch available in Linux kernel v5.1 issues a
warning for such unused break statements.
In the process of reviewing the new checkpatch for its inclusion
in OpenOCD, let's get rid of these warnings.
The script checkpatch is unable to fixup automatically this case.
Thanks to having "break" command using a single code line, this
patch has been generated using the script below:
find src/ -type f -exec ./tools/scripts/checkpatch.pl -q \
--types UNNECESSARY_BREAK -f {} \; \
| sed -n '/^#/{s/^.*FILE: //;s/:$//;s/:/ /;p}' \
| awk 'function P() {print "sed -i '\''"b"'\'' "a};
{
if ($1!=a) {
if (a) {P()};
a=$1;
b=$2"{d}";
} else {
b=b";"$2"{d}"
}
};
END {P()}'
Change-Id: I56ca098faa5fe8d1e3f712dc0a029a3f10559d99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5617
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Commit c2cecc74b0 ("Move JTAG interface list to new files.")
merged in mid 2009 introduces an unused and empty function that
the developer expects to use for loading adapter drivers from
shared libraries. This have never happened and the function is
still empty and unused.
Remove it.
Change-Id: I7c88dbf8a9747e96e5ca4e6e7038ac0f232604fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5601
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Empty lines at end of text files are useless.
Remove them.
Change-Id: Ibac9b36682d58f81e34ca2b51e6260e7d472fb0e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5172
Tested-by: jenkins
GCC 10 defaults to -fno-common which breaks the sharing of bitbang_swd
struct between bitbang drivers due to a missing extern.
Change-Id: I2b4122f7939cec91a72284006748f99a23548324
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/5592
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
By default the list of VID/PID is empty so if ftdi_vid_pid is not called
then no matches are attempted. The only message is at -d3:
Command 'init' failed with error code -100"
Check for this condition explicitly to make life easier for people
configuring adapters.
Change-Id: If0f93370c9e9ddc9700aae7c346c1c6dd319152e
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5440
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
This commits adds debugging support for the Mellanox BlueField
SoC via rshim, which is an interface accessible from external USB
or PCIe (for SmartNIC case) via the rshim driver. It implements
the arm dap interfaces based on the existing dapdirect framework.
Change-Id: I18eb1c54293ec2c581f853e0e55b3f96d7978b56
Signed-off-by: Liming Sun <lsun@mellanox.com>
Reviewed-on: http://openocd.zylin.com/5457
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
scan-build-9:
Description: Potential leak of memory pointed to by 'cmd'
File: /home/vanekt/openocd/scanbuild9/../src/jtag/drivers/ulink.c
Line: 1075
Description: Potential leak of memory pointed to by 'cmd'
File: /home/vanekt/openocd/scanbuild9/../src/jtag/drivers/ulink.c
Line: 1275
ulink_append_xxx_cmd() functions allocate memory for cmd
and then call ulink_allocate_payload(), which allocates cmd->payload_out
or cmd->payload_in.
ulink_append_queue() checks the size of queue and if the new payload
does not fit, calls ulink_execute_queued_commands() and then
ulink_post_process_queue(). If any of these two fails, an error is
returned, allocated cmd struct leaks and the queue is left in an undefined
state.
Change ulink_append_queue() flow to proceed to appending cmd to the queue
even in the case of fail in previous ulink_execute_queued_commands()
or ulink_post_process_queue(). In case of fail then clear the queue
including the last appended cmd.
Change-Id: I967c07af19e9020c93bcb4ef403cf1f557dd1db1
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5370
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
scan-build-9:
Description: Access to field 'payload_in' results in a dereference
of a null pointer (loaded from field 'queue_start')
File: src/jtag/drivers/ulink.c
Line: 2216
Set input/output_signals conditionally if ulink_append_get_signals_cmd()
and ulink_execute_queued_commands() returns no error.
Do not fail driver initialisation as the signals are only printed.
Change-Id: I6c842f0e9a604712abf7444a2fa95ba5810de1ff
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5520
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
As a consequence of a previous failed SWIM command any
subsequent attempts to enter SWIM mode fails. Change
stlink_usb_mode_enter to use stlink_usb_xfer_noerrcheck
instead.
Change-Id: I5c6a1a8e68d3dc77ec37264880383366fa6a75d9
Signed-off-by: Ake Rehnman <ake.rehnman@gmail.com>
Reviewed-on: http://openocd.zylin.com/5547
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
In order to extend the driver to support stlink-server over TCP,
we should always use a valid endpoint, as stlink-server is not permissive
and do not accept the invalid STLINK_NULL_EP.
STLINK_NULL_EP value was used for commands without an expected reply,
this value could be replaced with a valid endpoint without any impact
when the size is set to zero.
Change-Id: I003ad364e03d3a10bc036772db86310d996cbe81
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5455
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Not all the jtag drivers have been migrated to the new reset model
and for those only we need to flush the jtag queue to make the
reset working with command 'adapter [de]assert ...'.
Add a queue flush and a FIXME comment to remove both when all the
drivers would be migrated.
Change-Id: Ib6667f987b1be2bce492841040302e742dd1cad1
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5430
Tested-by: jenkins
The usleep() function, and its associated useconds_t type
specifier, has been obsoleted by POSIX.1-2008.
OpenOCD has 28 call to usleep(), that should be migrated to the
replacement nanosleep(), but due to the different prototype
int nanosleep(const struct timespec *req, struct timespec *rem);
this can take some effort.
The type useconds_t is used in only one case, where it's used both
as parameter of usleep() and as value passed to LOG_DEBUG(). Due
to different implementation of useconds_t, there are cases that
trigger a compile warning in LOG_DEBUG() when useconds_t is more
than 32 bit.
E.g. with unistd.h in MinGW 4.x, useconds_t is defined as unsigned
long, thus being 32 or 64 bits depending on the target.
Replace the only instance of useconds_t.
Change-Id: I21724f8b06780abdb003a57222ff1d6840ff5419
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5544
Tested-by: jenkins
Reviewed-by: Ake Rehnman <ake.rehnman@gmail.com>
Return bool value in functions that return bool.
Change return type to bool to function is_gpio_valid().
Change-Id: Ic2e62be737772b22e69881c034956549f659370b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5552
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
While stlink v2 allows setting the jtag clock frequency till a max
of 18 MHz, the firmware seams unstable and not properly working.
Remove the entry for 18 MHz, at least until a fix get available.
Change-Id: I503e1b6a5709b5fbf1f1147fd3b5f34a0c5ee98c
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5465
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
stlink accepts a set of values for "adapter speed".
Fix the api khz() to return one of the allowed speed values.
Change-Id: Iac640b6f76935891ca25ac168cab3809707f19d9
Signed-off-by: Laurent LEMELE <laurent.lemele@st.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5464
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
The commit fafe6dfc9c ("adapter: add command "adapter [de]assert
srst|trst [[de]assert srst|trst]"") was proposed in gerrit well
before commit a61ec3c1d7 ("adi_v5_dapdirect: add support for
adapter drivers that provide DAP API") get merged, so it didn't
include a complete support for dap direct.
The merge upstream of the two commits lacks the support by command
"adapter [de]assert" for dap direct
Let command command "adapter [de]assert" handle dap direct.
Change-Id: I1a69f8ee877c8fd57598ed4ad9d71da61d15457c
Fixes: commit fafe6dfc9c ("adapter: add command "adapter [de]assert srst|trst [[de]assert srst|trst]"")
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5515
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The XDS110 supports alternate configurations, each of which has
a unique vid/pid:
0451/bef3 -- Standard (legacy) configuration
0451/bef4 -- Drag-n-Drop configuration
1cbe/02a5 -- CMSIS-DAP 2.0 on BULK interface configuration
It's not important to OpenOCD what the differences are except
that OpenOCD needs to know how to connect using the different
vid/pids and, in the case of the last one, use a different
interface for the debug connection.
Updated the XDS110 source to search for all possible
configurations, and updated the udev rules file to enable
user access to the alternate configuraitons.
For the curious, you can download the latest XDS emupack from
software-dl.ti.com/ccs/esd/documents/xdsdebugprobes/emu_xds_software_package_download.html
Install to an empty directory, and documentation for the
XDS110 is located in the .../ccs_base/common/uscif/xds110
of the installation.
Updated for comments in code review. Changed const variable
names to lower case. Reworked interface/endpoint setting
to use arrays suggestion.
Change-Id: Icc9d11c6618f43d87ae8171c78ebf238800d3ac2
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5494
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Arrange all commands under a top level xds110 command. Fix
documentation to properly reflect the current functionality.
Also updated the links in the document to the new permanent
links for the XDS110 only support.
Patch updated for comments from code review. Return
ERROR_COMMAND_SYNTAX_ERROR for wrong number of args in
commands. Added deprecated commands to src/jtag/startup.tcl.
Change-Id: Ica45f65e1fdf7fa72866f4e28c4f6bce428d8ac9
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5495
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Starting with XDS110 firmware version 3.0.0.0, the peak TCK
frequency became 14,000 kHz. So the delay count calculation
in the current driver has been updated to use the new
formula for setting the TCK speed depending on which version
of the firmware is detected. And because of the changes, the
default TCK settings for the XDS110 based Launchpads can be
adjusted to take advantage of the higher TCK performance.
Note that the values used have been determined through
testing in the automated test labs to be the highest TCK
frequency with the XDS110 that are still reliable.
Different boards have a different peak TCK setting that
should be safe.
Change-Id: I4d66e90d8fac8272641ba4db4a3a510e3b444d86
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5493
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Old ST-LINK DFU returns an incorrect serial in the USB descriptor
example for the following serial "57FF72067265575742132067"
- the correct descriptor serial is:
0x32, 0x03, 0x35, 0x00, 0x37, 0x00, 0x46, 0x00, 0x46, 0x00 ...
this contains the length (0x32 = 50), the type (0x3 = DT_STRING)
and the serial in unicode format.
the serial part is: 0x0035, 0x0037, 0x0046, 0x0046 ... >> 57FF ...
this format could be read correctly by 'libusb_get_string_descriptor_ascii'
so this case is managed by libusb_helper::string_descriptor_equal
- the buggy DFU is not doing any unicode conversion and returns a raw
serial data in the descriptor:
0x1a, 0x03, 0x57, 0x00, 0xFF, 0x00, 0x72, 0x00 ...
>> 57 FF 72 ...
based on the length (0x1a = 26) we could easily decide if we have to fixup the serial
and then we have just to convert the raw data into printable characters using sprintf
example for an old ST-LINK/V2 standalone:
before : 'W?rreWWB g'
after : '57FF72067265575742132067'
=> same as the displayed value in STM32CubeProgrammer
tested using these commands
using the buggy serial
-c "hla_serial \x57\x3f\x72\x06\x72\x65\x57\x57\x42\x13\x20\x67"
using the computed serial
-c "hla_serial 57FF72067265575742132067"
Change-Id: I1213818257663eeb8e76f419087d3127d0524842
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5396
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
introduce a callback function that could be passed to jtag_libusb_open
to permit adapters to compute their custom/exotic serials.
the callback should return a non NULL value only when the serial could not
be retrieved by the standard 'libusb_get_string_descriptor_ascii'
Change-Id: Ib95d6bdfc4ee655eda538fba8becfa183c3b0059
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5496
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
TCK during nSRST assert/deassert code.
To support LPRF targets (CC13xx/CC26xx), TCK must be toggled
for 50 ms while nSRST is asserted and right after it is
released. This allows the core to halt in boot ROM before
code is run that might interfere with debug access.
The current routine has two issues. It shouldn't be run at
all if the target is using SWD. And the delay needs to
be a real-time 50 ms, so the number of TCK periods should
be calculated off the set speed.
Change-Id: If993031b84cf2a505ea67a6633602c4b01cd8e1e
Signed-off-by: Edward Fewell <efewell@ti.com>
Reviewed-on: http://openocd.zylin.com/5497
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The function ftdi_set_signal() does not propagate the pin change
until next call to mpsse_flush(). Current code does not toggles
immediately the reset pins if polling is turned off.
Call mpsse_flush() at the end of ftdi_reset().
While there, remove the duplicated LOG message.
Change-Id: I79eacfe4fc32b5cdf2dc1b78f3660d96988466bc
Fixes: 8850eb8f2c ("swd: get rid of jtag queue to assert/deassert srst")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5431
Tested-by: jenkins
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The jtag API reset() is synchronous, but this was not highlighted
in the description.
Change-Id: I76ffb7eec97c8608cfbef0b9268ee18a5f50b221
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: 8850eb8f2c ("swd: get rid of jtag queue to assert/deassert srst")
Reviewed-on: http://openocd.zylin.com/5471
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Writing bits to an uninitialized buffer generated false warnings.
Zero buffers before setting them by buf_set_u32|64()
(do it only if bit-by-bit copy loop is used,
zeroed buffer is not necessary if a fast path write is used)
Change-Id: I2f7f8ddb45b0cbd08d3e249534fc51f4b5cc6694
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5383
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The name 'common' does not make sense anymore. While at it,
remove some unnecessary #includes.
Change-Id: If9798a5cce179438d89428a598d8ca05c8e5f20c
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5434
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Supporting two libusb versions provides additional development challenges
without additional advantage. In most cases we need to patch libusb0_common and
libusb1_common without real ability to test libusb0_common.
Change-Id: Icbb19c6809b14533fe2acf7a877377b3be4cbd61
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/5432
Tested-by: jenkins
The script checkpatch available in new Linux kernel offers an
experimental feature for automatically fix the code in place.
While still experimental, the feature works quite well for simple
fixes, like spacing.
This patch has been created automatically with the script under
review for inclusion in OpenOCD, using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types POINTER_LOCATION --fix-inplace -f {} \;
then manually reviewed.
OpenOCD coding style does not mention the space around pointer's
asterisk, so no check is enforced. This patch only makes the style
uniform across the files.
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: Iefb4998e69bebdfe0d1ae65cadfc8d2c4f166d13
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5197
Tested-by: jenkins
Reuse the existing tracing functionality of HLA mode to support
tracing in DAP direct mode.
Change-Id: I75a01e88ba5d3e45717e4108b99697ac3225db9e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5409
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
We have the macro ARRAY_SIZE() already available. Use it!
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types ARRAY_SIZE -f {} \;
Change-Id: Ic7da9b710edf118eacb08f9e222f34208c580842
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5198
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Command CMD_STOP_SIMU had been defined in jtag_vpi for a long time
(since the beginning?) but has not been utilized until now.
Its purpose is to signal to the jtag_vpi server (i.e. the RTL
simulation software) that the simulation shall be stopped.
This commit adds a TCL configuration command that selects whether
CMD_STOP_SIMU will be sent to the jtag_vpi server when OpenOCD is
about to exit. This functionality is off by default to maintain
identical behavior as in previous OpenOCD versions, unless the user
enables it explicitly.
Change-Id: If3894af6efa61038ccf6c9191f664e2128f2ef11
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5407
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Replace "Instruction Register (DR)" with "Instruction Register (IR)",
that is sed "s@DR@IR@", which was likely a copy-paste error.
Change-Id: I3e625872c855d655485b3efa5f50fe1c00ecbf52
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-on: http://openocd.zylin.com/5446
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
While ST internal documentation for STLINK-V3 reports that 8 bits
read/write commands handle 512 bytes of data, a firmware bug makes
it crashing on high data size.
This is fixed with firmware V3J6 (shipped together with V2J36).
Check for firmware version to use the proper data size.
Change-Id: Iaba6cd26bbe130097c1c19de610680e0e8b69bfc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: https://sourceforge.net/p/openocd/tickets/259/
Reviewed-on: http://openocd.zylin.com/5408
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If the TLR sequence is sent as result of the command "adapter
assert trst" while polling is off, the TLR sequence is not sent out
until a following jtag operation.
Flush the jtag queue before return.
Change-Id: I20efd7137cb7b1d1c4f73c1362cbe4e57aeaae49
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5405
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The macro PCI_CFG_SPACE_EXP_SIZE is exposed to userspace from
Linux kernel v4.10, with commit cc10385b6fde ("PCI: Move config
space size macros to pci_regs.h")
http://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=cc10385b6fde
Define the macro in the driver code, if not already defined.
Change-Id: I610219a2587eff2c142102b9f7830e3da882af78
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5435
Reviewed-by: Moritz Fischer <moritzf@google.com>
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Tested-by: jenkins
The fallback provided for the jtag_reset command always fails with a
strange message: 'Error: invalid command name "de"'
This is caused by incorrect quoting inside the warning message.
Fixes: c07b774e8f ("jtag: replace command "jtag_reset" with "adapter [de]assert"")
Change-Id: Icd47fca2b5a7b33474bfb0040e88193a0968f301
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5416
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Replace in the code any reference to the deprecated commands.
Change-Id: I75d28064017d664990b4024967900f32e196230a
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5282
Tested-by: jenkins
Reviewed-by: Marc Schink <dev@zapb.de>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
currently we have different types of same command group:
- starting with adapter_*
- starting with interface*
- without adapter or interface prefix.
Since interface name is already used, we can only use "adapter" command
group by keeping old commands as well.
Change-Id: Id0a1cb63a2ea6860c67ae1e7a3a06a37ddf464f4
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4774
Reviewed-by: Marc Schink <dev@zapb.de>
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Commit [1] was submitted in gerrit well before the conflicting
commit [2] get merged in master branch. While it was fine
committing in master branch [1] alone, it should not be
committed "as is" after [2].
Unfortunately gerrit did not complained committing [1] after [2].
The result is that master branch does not build anymore when the
driver xlnx-pcie-xvc is enabled at configure time by the optional
flag --enable-xlnx-pcie-xvc.
Apply to the driver the required changes as in [2].
While there, remove the duplicated struct xlnx_pcie_xvc_transports
and the struct field already implicitly initialized to zero.
[1] ff6d0704ec ("jtag: drivers: xlnx-pcie-xvc: Add support for
Xilinx XVC/PCIe")
[2] efd1d64222 ("adapter: switch from struct jtag_interface to
adapter_driver")
Change-Id: I5498479b802a231afbee1b845ae9775e1da7c728
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5402
Reviewed-by: Moritz Fischer <moritzf@google.com>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
A USB bulk write/read operation may fail with different errors:
LIBUSB_ERROR_TIMEOUT if the transfer timed out (and populates transferred)
LIBUSB_ERROR_PIPE if the endpoint halted
LIBUSB_ERROR_OVERFLOW if the device offered more data, see Packets and overflows
LIBUSB_ERROR_NO_DEVICE if the device has been disconnected
another LIBUSB_ERROR code on other failures
Current OpenOCD code is using the transfer size based error detection.
Which may not always work. For example for LIBUSB_ERROR_OVERFLOW as libusb
documentation says:
"Problems may occur if the device attempts to send more data than can fit in
the buffer. libusb reports LIBUSB_TRANSFER_OVERFLOW for this condition but
other behaviour is largely undefined: actual_length may or may not be accurate,
the chunk of data that can fit in the buffer (before overflow) may or may not
have been transferred."
This patch is refactoring code to use actual error return value for
error detection instead of size.
Change-Id: Iec0798438ca7b5c76e2e2912af21d9aa76ee0217
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-on: http://openocd.zylin.com/4590
Tested-by: jenkins
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Add support for Xilinx Virtual Cable over PCIe JTAG controller.
It is commonly used in Xilinx based PCI Express designs with JTAG IP
in the FPGA fabric.
Access to the JTAG registers happens via the PCI Express extended
configuration space.
This can be used to debug soft-cores instantiated in the FPGA fabric.
The clang static checker doesn't find any new problems with this change.
Change-Id: Ib12ede0d1f26dacfda808d5e05b947b640c5bde7
Signed-off-by: Moritz Fischer <moritzf@google.com>
Reviewed-on: http://openocd.zylin.com/5314
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Marex
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Arm DPv1 and DPv2 support banked registers by setting the bank in
field DPBANKSEL of register DP_SELECT.
Old ST-Link firmware don't support banked registers and setting a
bank other than bank zero on DPv1 or DPv2 cause issues in the
firmware because it cannot set back bank zero to read CTRL/STAT.
New ST-Link firmware mask away DPBANKSEL bits while writing in
DP_SELECT but support banked register using the same packed method
used by OpenOCD:
#define BANK_REG(bank, reg) (((bank) << 4) | (reg))
Add a new macro STLINK_F_HAS_DPBANKSEL for firmware that support
arm DPv1 and DPv2, plus trigger an error if banked registers are
requested on old firmware.
Prevent changing DPBANKSEL on old firmware.
Log a debug message when changing DPBANKSEL will be ignored.
Change-Id: Iaa592517831d63f8da2290db54f6b32504e3081b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4978
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
STLINK-V3 and the new firmware V2J24 for ST-LINK/V2 provide API
to directly access the DAP registers.
This mode permits to use the native target in cortex_m.c, with no
need to override it with the target in hla_target.c.
Other advantages wrt HLA are: support for Cortex-A cores, support
for SoC multi-core and/or multi AP, support for OpenOCD commands
"dap" thus including control of CSW.
This obsoletes the existing HLA driver for ST-Link, that should
anyway be kept for those cases where it's not possible to update
the ST-Link firmware.
This commit introduces the minimal implementation for direct DAP
access. The implementation is much slower than the HLA because
every memory transfer requires several USB packets. Further
commits will close the performance gap.
The whole ST-Link driver is compiled under BUILD_HLADAPTER, to
remove the need to split the driver between the two modes. This
has to be reworked, but it's quite invasive!
A new interface file stlink-dap.cfg is added and should be used
in place of stlink.cfg to enable the DAP mode.
Documentation is updated and reports limitation on the maximum AP
number that can be accessed by ST-Link for some firmware already
tested.
Change-Id: I932ffe16bc81d00b1fe489e2944fda13470cce9b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4904
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Some high level adapters, like STLINK-V3 and new firmware for
ST-Link/V2, provide API to directly access the DAP registers
hiding the details of the physical transport JTAG or SWD.
OpenOCD has already the intermediate API in struct dap_ops that
are suitable for such adapters, but are not exposed to the
adapter drivers.
Add in struct adapter_driver two independent struct dap_ops for
the cases of physical JTAG and SWD transport.
Add new transport names "dapdirect_jtag" and "dapdirect_swd", to
be used by the drivers that provide one or both DAP API.
Add the necessarily glue in target/adi_v5_dapdirect.c
Change-Id: I2bb8e3a80fba750f2c218d877cfa5888428e3c28
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4903
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To reorganize the adapters code, introduce an adapter_driver
struct that contains all the adapter generic part, while
keeping in two separate struct the specific API jtag_ops and
swd_ops.
Move the allocation of *adapter_driver from the JTAG-specific
file core.c to the more adapter-specific file adapter.c
While splitting the old jtag_interface for every driver, put
the fields in the same order as in the struct declaration so
we keep a consistent code across all the drivers.
While other transport specific API could/would be added as
separate ops, nothing is done here for HLA.
Change-Id: I2d60f97ac514c0dd2d93a6ec9be66fd9d388dad5
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4900
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
kitprog is SWD only and we do not rely on JTAG queue anymore.
Remove the remaining JTAG heritage.
Change-Id: Ic586278368301eb669bc6e4e641f683a81cb171d
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4899
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
We do not rely on JTAG queue anymore.
Remove the remaining JTAG heritage.
Change-Id: I6c87d9ffebaa383c998cf273188b3e7f28b3fe95
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4898
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
After the cleanup of swd and hla, there should be no more calls
to jtag_execute_queue() or to queue jtag commands if current
transport is not jtag. Thus we can start removing the jtag
specific code from adapters that do not support jtag.
To prevent some remaining call to jtag_execute_queue() to crash
openocd, verify the transport, print an error message if the
transport is not jtag, call the adapter's jtag_execute_queue()
only if it exist.
To identify code that still add commands in the jtag queue even
if transport is not jtag, print an error message in the function
jtag_queue_command(). For the moment, still queue the message,
even if will cause a memory leak if there is no following call
to jtag_execute_queue(); the target is to identify the issue and
cleanup the code, thus solving also the leak.
Change-Id: I8fc85f754aa057aad1df05ff0448c8619897da23
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4897
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
HLA uses its own internal driver's API to control the adapter's
system reset, but at the same time it calls jtag_add_reset() to
avoid breaking the internal logic of OpenOCD. This implicitly
forces HLA to rely on jtag queue mechanism, even if HLA has no
link with JTAG state machine. It requires HLA to implement an
empty execute_queue() to comply with the JTAG queue.
Modify the HLA framework and the HLA targets to use the new
adapter API for system_reset and decouple HLA from JTAG queue.
Rename the HLA static functions adapter_assert_reset() and
adapter_deassert_reset() to avoid overlap with the global
functions with same name.
While there, fix a minor typo in a comment s/incase/in case/.
Do not remove from HLA the JTAG specific API execute_queue(),
even if not required anymore, because OpenOCD code still has
calls to jtag_execute_queue() in case of non JTAG transport.
Change-Id: I0e65e3e557bd665bd3d3aeaa84ea609b55a05e48
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4896
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Remove the JTAG_RESET command from the bitbang execute queue now
that all bitbang drivers have moved away from old reset method.
Remove also the internal reset API in struct bitbang_interface.
Tested parport only.
Change-Id: I12b157ef442f4c9912406b19b7a4d32ba6ec0b53
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5300
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The transport SWD uses the JTAG queue to assert/deassert the
system reset srst. This is the major inconsistency that has to be
removed to properly split JTAG and SWD.
Introduce a new driver API, reset(), to controls both the signals
trst and srst in the driver, skipping the JTAG queue. Put the new
API in struct jtag_interface, even if in this patch it's used for
SWD only; the goal is to get it reused by the other transports.
Add the implementation of the API in all the drivers that
implement SWD. Such implementation is almost the same of the old
code in JTAG queue.
Create a wrapper adapter_system_reset() to use the new API and
remove the SWD specific swd_add_reset(). In the wrapper replace
jtag_add_sleep() with jtag_sleep(), because the former uses the
JTAG queue too.
Rename the old jtag_add_reset() as legacy_jtag_add_reset() with
the target to remove it when all drivers would be ported to the
new reset API. Create a new jtag_add_reset() that calls the
legacy function for drivers still on the old reset API.
Use the new API also on JTAG transport for the drivers that can
support both SWD and JTAG.
For the moment, do not modify the implementation of JTAG-only
drivers, which will continue using the usual method. This should
be cleaned-up in future commits.
Change-Id: I32331c88313f6059b25e12c6bb0156aebc1c074f
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4895
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The method to send an arbitrary sequence to DAP depends on the
transport and is thus different on JTAG and SWD. This is already
coded in dap_to_jtag() and dap_to_swd().
Add a new API send_sequence() in struct dap_ops.
Add the implementations of send_sequence() in adi_v5_jtag.c and
adi_v5_swd.c
Rewrite dap_to_jtag() and dap_to_swd() using the new API.
Move the enum swd_special_seq in arm_adi_v5.h to solve a circular
dependencies among swd.h and arm_adi_v5.h
Change-Id: I9db13a00f129761eab283783c094cfff2dd92610
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4902
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Replace the JTAG transport specific command with a more generic
one. Deprecate "jtag_reset" and update the documentation.
While there, fix an error in the documentation, where the command
"jtag_reset" was used in place of command "reset_config".
Change-Id: I41a988d37ce69f7b35a960cbaf5306aab0299b99
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5286
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Inspired from http://openocd.zylin.com/#/c/3720/1
Add commands to control the adapter's signals srst and trst.
Add macros for the flag's values assert/deassert to make clear what
they mean and to propose a uniform set of values across the code.
Change-Id: Ia8b13f4ded892942916cad7bda49540a896e7218
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5277
Tested-by: jenkins
- Fix: Proper handling of read_socket() and write_socket()
in case of "partial" read/write.
- Added low-level JTAG IO debug capability (_DEBUG_JTAG_IO_)
- Zero-fill packet buffers, avoid sending pieces of uninitialized
memory over the network (memset struct vpi_cmd)
- Use close_socket() instead of close() - needed for Win32
- Fixed usage messages of jtag_vpi_command_handlers
Change-Id: I8bd19bc5c9512fe8e798600212e8a95213f50f5b
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5177
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The SWO frequency auto-detection with J-Link adapters does not work
properly in the current implementation. This is because the trace layer
has only information about the highest possible SWO frequency supported
by the adapter. With that the trace layer calculates the SWO prescaler
which usually leads to a frequency deviation greater than what is
permitted by J-Link adapters.
Move the calculation of the SWO prescaler from the trace layer into the
trace configuration of the adapter to overcome this problem.
The adapter has the necessary information to choose a suitable SWO
frequency and calculate the corresponding prescaler that complies with
the maximum allowed frequency deviation.
Tested with:
- STM32L152RC Discovery Kit (ST-Link)
- EFM32GG-STK3700 (J-Link)
Change-Id: I38ff2b89d32f0a92c597989b590afe5c75cf4902
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3903
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
When a gpio is exported by writing in /sys/class/gpio/export, the
corresponding gpio control files appear immediately in sysfs but
with default access permission for root user only. The daemon udev
requires some time to get notified of the new files before it can
change the permissions to allow access to unprivileged users.
Due to this race condition, sysfsgpio can fail with EACCES error
if OpenOCD is executed by any unprivileged user.
Give 0.5 seconds to udev to identify the new files and change the
permission.
Tested with udev rules:
SUBSYSTEM=="gpio*", PROGRAM="/bin/sh -c 'find -L /sys/class/gpio/ -maxdepth 2 -exec chown root:uucp {} \; -exec chmod g=u {} \; || true'"
Change-Id: I1316c66ff103ffe23e5e4720f33372dc272a3766
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5302
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Made sure that size and endianness of jtag_vpi structures sent
over the network is the same, regardless of the platform.
Little endian chosen to maintain as much compatibility
with existing OpenOCD builds as possible.
Matching change in the original jtag_vpi server:
https://github.com/fjullien/jtag_vpi/pull/4
Change-Id: Ib839fea9bb2d5190b5643c970b89333b286dce71
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5152
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
If a new JTAG command is added, then GCC will complain that
enumeration value not handled in switch. This is the only driver not
to have a default case, so add it.
Change-Id: Icb838087bb7525d057a911bd256300e256da1668
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://openocd.zylin.com/5333
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
If a new JTAG command is added, then GCC will complain that
enumeration value not handled in switch. Make this consistent with
other drivers, and add a 'default' case.
Change-Id: I66d6d0db3fcae93ea246f2d4882ffff5dec14693
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://openocd.zylin.com/5340
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This version adds two new USB PIDs and fixes a build issue under MSYS2.
Change-Id: I753fab827783ea64e55e59d833742c9f70a28a2b
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5309
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The variable gw16012_port is of type uint16_t.
There is no need for a cast to print it.
Change the format modifier to PRIx16
Change-Id: I16fe688b9d235bae46525635d07849a00fba9548
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5195
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
I think that libusb_handle_events_timeout_completed is supposed to make
progress or time out, but sometimes we hit a case where it makes no
progress, and mpsse_flush() loops forever. This wall clock timeout
notifies the user that this is going on.
When I wrote this code, this bug would reproduce every hour or two, but
right now it's not happening for me.
Change-Id: I7eb66f43462298e263a48048aa0c8769095661eb
Signed-off-by: Tim Newsome <tim@sifive.com>
Reviewed-on: http://openocd.zylin.com/4767
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Fix expression "(pin_status | 0x4)" which was always true rather than
testing a bit. Untested - was clearly not expressing the intent of the
author by inspection. Found by automated tooling and rtrieu@google.com.
Signed-off-by: Seth LaForge <sethml@google.com>
Change-Id: I4bb91e60e8ce9757bf21976cc48de6f85a39c68d
Reviewed-on: http://openocd.zylin.com/5301
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The TCL command "return" always returns error code JIM_RETURN, to
indicate that the effective error code and message are elsewhere.
In the current implementation, the caller of jtag's event only
checks for return code JIM_OK and considers any other value,
including JIM_RETURN, as an error condition.
It can be tested running openocd on a jtag target and adding a
jtag event "setup" with a single line "return", e.g.
openocd -f board/ti_cc3200_launchxl.cfg \
-c 'jtag configure cc32xx.cpu -event setup return'
to get the message:
../src/jtag/core.c:1599: Error:
in procedure 'jtag_init' called at file "../src/jtag/core.c",
line 1599
Modify jtag_tap_handle_event() to detect the specific return value
of the "return" command and to test the real error code that is,
eventually, specified to the TCL "return" command.
Change-Id: I6d6febc15ef169638afffbffc1810e0b84fcf5c8
Reported-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5199
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Commit c2e18bfaea changed the size of the JTAG-to-SWD sequence
from 15 bytes to 17 bytes. This broke SWD switch sequence transfer
for buspirate, since buspirate packets can only hold a payload of up
to 16 bytes and we tried to fit the whole sequence in a single packet.
Splitting up the sequence transfer in appropriately sized packets
makes buspirate SWD work again (successfully tested with buspirate
firmwares v6.1 and v7.0).
Change-Id: Ib5b412b9e77287d705d2762e31c16d30318b50e3
Signed-off-by: Tilman Sauerbeck <tilman@code-monkey.de>
Reviewed-on: http://openocd.zylin.com/5200
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: If1f56fd5d610b993a4ecbc900fac9f90638037c9
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5202
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
For legacy support, drivers that do not define a list of
transports get identified as jtag_only.
Cleanup this old crust and initialize properly the transports
field in the jtag_interface for all the drivers.
Change-Id: I9c86064e5d05bd0212bc18f4424414e615e617fe
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4893
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
There is just a single entry point for the jtag API .khz(),
.speed_div(), .power_dropout(), .srst_asserted().
Simplify the code by in-lining the default handler.
The overall code behaviour is not changed.
This change prevents modifying at run-time the content of
struct jtag_interface.
Inspired from change http://openocd.zylin.com/943
by Evan Hunter <ehunter@broadcom.com>
Change-Id: I09aeb76d614db57b1884ac7ee9f00c152cd77849
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4892
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The specific SWD API to change/query the adapter speed is never
called because the equivalent JTAG API is used in place of it.
In the restructure of struct jtag_interface, the JTAG API is
promoted as global adapter API, thus a specific SWD one is not
anymore required.
Change-Id: I1e810d255b4dfcd5791b4fac8ae1260c31a057fd
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/4891
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
The warning appears for every possible device during enumeration
and provides no useful information for an end-user.
Change-Id: I56e7889a5d9d4656de13ad9e21be3a6e1906e05f
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/5155
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Two calls to command_print() in imx_gpio fixed - the first parameter
adjusted (CMD_CTX -> CMD) per the changes from this commit:
6cb5ba6f11
Change-Id: I6cb0909439a632d3109edfc68070b9b561f86d49
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5176
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
The commit 84ca4995ad ("drivers/bcm2835gpio: fix usage messages")
has been merged before commit 6cb5ba6f11 ("helper/command: change
prototype of command_print/command_print_sameline") introducing two
new call to command_print() that were not modified by the second
commit.
This triggers a compile error on ARM host.
Fix the incorrect function call.
Change-Id: I2736bae24141685b7590fd6b4aa5e6a29b2cab29
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5174
Tested-by: jenkins
In jtag_vpi_stableclocks() the TMS line needs to be set properly
based on the current JTAG TAP state (TMS=1 in TAP_RESET state vs.
TMS=0 in other cases).
Change-Id: Id49622ba83015f97b61b6a896edde4448f1fbdc6
Signed-off-by: Jan Matyas <matyas@codasip.com>
Reviewed-on: http://openocd.zylin.com/5151
Tested-by: jenkins
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Prevent the State Machine from moving at the end
of several cycles during run_test_idle
state.
Change-Id: Iabdf90a58334dd3d0e6e34b02983a85662062825
Signed-off-by: Megan Wachs <megan@sifive.com>
Reviewed-on: http://openocd.zylin.com/3635
Tested-by: jenkins
Reviewed-by: Jan Matyas <matyas@codasip.com>
Reviewed-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should switch to CMD as
first parameter.
Change prototype of command_print() and command_print_sameline()
to pass CMD instead of CMD_CTX.
Since the first parameter is currently not used, the change can be
done though scripts without manual coding.
This patch is created using the command:
sed -i PATTERN $(find src/ doc/ -type f)
with all the following patters:
's/\(command_print(cmd\)->ctx,/\1,/'
's/\(command_print(CMD\)_CTX,/\1,/'
's/\(command_print(struct command_\)context \*context,/\1invocation *cmd,/'
's/\(command_print_sameline(cmd\)->ctx,/\1,/'
's/\(command_print_sameline(CMD\)_CTX,/\1,/'
's/\(command_print_sameline(struct command_\)context \*context,/\1invocation *cmd,/'
This change is inspired by http://openocd.zylin.com/1815 from Paul
Fertser but is now done through scripting.
Change-Id: I3386d8f96cdc477e7a2308dd18269de3bed04385
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/5081
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
To prepare for handling TCL return values consistently, all calls
to command_print/command_print_sameline should be ready to switch
to CMD as first parameter.
Change prototype of show_config*() functions to pass CMD instead
of CMD_CTX.
This change was part of http://openocd.zylin.com/1815 from Paul
Fertser and has been extracted and rebased to simplify the review.
Change-Id: I131a904774bf60ad1bf9d90dbc65927c246ac23a
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5080
Tested-by: jenkins
The modified lines cause "runtime error: left shift of <X> by <Y>
places cannot be represented in type 'int'", because integer
literal is cast to int by default.
Change-Id: Ie38119b5eb46ee470e0d149959e523b48ac4d66d
Signed-off-by: Mete Balci <metebalci@gmail.com>
Reviewed-on: http://openocd.zylin.com/5005
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This can be used to dynamically distinguish between similar chips in tcl
code.
Change-Id: Ic4dfb61693e78616355173142dc7f9b9683a9f73
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-on: http://openocd.zylin.com/5033
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
The missing field causes runtime debug message
BUG: command '%s' does not have the '.usage' field filled out
While there, fix some minor typo in the help messages:
s/deasert/deassert/
s/Deasert/Deassert/
Change-Id: If3dd18265cda103ca0d05609f67f4ca58e7cbb27
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5024
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add usage and fix the help text of the command
Change-Id: I0e157d76f5d87bcda80f82a110912994908c8e03
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5023
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The notation "(tck tms tdi tdo)* " is incorrect, because it means the
quadruple of gpio can be repeated on the command-line.
The correct syntax of the command requires instead to provide either
all the four gpio numbers (in order to set the values) or to pass an
empty command-line (to dump the values previously set).
Change the .usage field to "[tck tms tdi tdo]".
Change similarly the corresponding .usage field for SWD command.
Add the .usage field for the commands that individually set each gpio
or gpio property.
Dump the previously set values when commands bcm2835gpio_speed_coeffs
or bcm2835gpio_peripheral_base are executed with empty command-line.
Change-Id: Ie45d8268c1de331aded0bb52d5e6b8f0e8766a5b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5019
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
The notation "(tck tms tdi tdo)* " is incorrect, because it means the
quadruple of gpio can be repeated on the command-line.
The correct syntax of the command requires instead to provide either
all the four gpio numbers (in order to set the values) or to pass an
empty command-line (to dump the values previously set).
Change the .usage field to "[tck tms tdi tdo]".
Change similarly the corresponding .usage field for SWD command.
Add the .usage field for the commands that individually set each gpio
or gpio property.
Dump the previously set values when commands imx_gpio_speed_coeffs or
imx_gpio_peripheral_base are executed with empty command-line.
Change-Id: Id56a68622817101bd0a46fed1fead6d2cd2b6ec6
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5018
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Yun Liu
Tomas Vanek
Antonio Borneo
Adrian Negreanu
Oleksij Rempel
Tarek BOCHKATI
Krzysztof Hockuba
Bohdan Tymkiv
Łukasz Misek
Mickaël Thomas
Marc Schink
Moritz Fischer
Cliff L. Biffle
John Pham
Kevin Burke
Samuel Obuch
Zale Yu
Michal Potrzebicz
Mikhail Rasputin
tscn92
Andreas Fritiofson
Leonard Crestez
Liming Sun
Ake Rehnman
Laurent LEMELE
Roman Elshin
Edward Fewell
Oleksij Rempel
Jan Matyas
Marek Vasut
Marc Schink
Alexandru Gagniuc
Tim Newsome
Seth LaForge
Tilman Sauerbeck
Christopher Head
Megan Wachs
Paul Fertser
Mete Balci