Since OpenOCD basically allows to perform arbitrary actions on behalf of
the running user, it makes sense to restrict the exposure by default.
If you need network connectivity and your environment is safe enough,
use "bindto 0.0.0.0" to switch to the old behaviour.
Change-Id: I4a4044b90d0ecb30118cea96fc92a7bcff0924e0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/4331
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: jenkins
While on it
- change some occurrences of gdb to GDB if it refers GDB software
(as oposed to a gdb command)
- add some xrefs
- give more meaningful example of target event definition
- remove obsoleted example of GDB hook-step
Change-Id: Ia2e26021d57f675acfa1de704f6c3e81c22bb8bf
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4444
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This change contains an alternative to Matthias Welwarsky's #4130
(target-prefixed commands) and to #4293 (event handlers).
get_current_target() must retrieve the target associated to the current
command. If no target associated, the current target of the command
context is used as a fallback.
Many Tcl event handlers work with the current target as if it were
the target issuing the event.
current_target in command_context is a number and has to be converted
to a pointer in every get_current_target() call.
The solution:
- Replace current_target in command_context by a target pointer
- Add another target pointer current_target_override
- get_current_target() returns current_target_override if set, otherwise
current_target
- Save, set and restore current_target_override to the current prefix
in run_command()
- Save, set and restore current_target_override to the event invoking
target in target_handle_event()
While on it use calloc when allocating a new command_context.
Change-Id: I9a82102e94dcac063743834a1d28da861b2e74ea
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Suggested-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4295
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <matthias@welwarsky.de>
This commit contains a rewrite of the jtagspi protocol and covers both
changes in the jtagspi.c openocd driver and the bscan_spi
(xilinx_bscan_spi) proxy bitstreams. The changes are as follows:
1. Always perform IR scan to ensure proper clearing of BYPASSed DRs.
2. Insert alignment cycles for all BYPASSed TAPs:
The previous logic was erroneous. The delay in clock cyles from a bit
written to the jtag interface to a bit read by the jtag interface is:
* The number of BYPASSed TAPs before this (jtagspi) tap
* The length of the jtagspi data register (1)
* The number of BYPASSed TAPs before this one.
I.e. it is just the number of enabled TAPs. This also gets rid of the
configuration parameter DR_LENGTH.
3. Use marker bit to start spi transfer
If there are TAPs ahead of this one on the JTAG chain, and we are in
DR-SHIFT, there will be old bits toggled through first before the first
valid bit destined for the flash.
This delays the begin of the JTAGSPI transaction until the first high bit.
4. New jtagspi protocol
A JTAGSPI transfer now consists of:
* an arbitrary number of 0 bits (from BYPASS registers in front of the
JTAG2SPI DR)
* a marker bit (1) indicating the start of the JTAG2SPI transaction
* 32 bits (big endian) describing the length of the SPI transaction
* a number of SPI clock cycles (corresponding to 3.) with CS_N asserted
* an arbitrary number of cycles (to shift MISO/TDO data through
subsequent BYPASS registers)
5. xilinx_bscan_spi: clean up, add ultrascale
This is tested on the following configurations:
* KC705: XC7K325T
* Sayma AMC: XCKU040
* Sayma AMC + RTM): XCKU040 + XC7A15T, a board with integrated FTDI JTAG
adapter, SCANSTA JTAG router, a Xilinx Ultrascale XCKU040 and a Xilinx
Artix 7 15T. https://github.com/m-labs/sinara/wiki/Sayma
* Custom board with Lattice FPGA + XC7A35T
* CUstom board with 3x XCKU115-2FLVA1517E
Change-Id: I7361e9fb284ebb916302941735eebef3612aa103
Signed-off-by: Robert Jordens <jordens@gmail.com>
Reviewed-on: http://openocd.zylin.com/4236
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Events reset-halt-pre, reset-halt-post, reset-wait-pre and
reset-wait-post are not used anywhere.
Change-Id: I9a0f94875b102d9b08f6c2fd9d73a9f05f8e8e79
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4285
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
also remove legacy footnote as it adds no value.
Change-Id: I3892acf244bd8fba6f844a5d82a66004e193a395
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/4309
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Extend HLA interface to allow multiple VID/PID pairs and use it to
autodetect the connected stlink version.
Change-Id: I35cd895b2260e23cf0e8fcb1fc11a78c2b99c69b
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3961
Tested-by: jenkins
Reviewed-by: Karl Palsson <karlp@tweak.net.au>
Reviewed-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add "arm semihosting_cmdline [argv0 argv1 ...]" for setting the
command line arguments for the debuggee.
[andreas.fritiofson@gmail.com]: Dynamic allocation, empty default
Change-Id: I831ddd161d602f251940e29608a154e9590fdee1
Signed-off-by: Christian Groessler <chris@groessler.org>
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3106
Tested-by: jenkins
Renaming of all nrf51 NOR flash code to nrf5, as to prepare the
code for being able to flash nrf51 and nrf52 chips.
The nrf51 command is retained for backwards compatability.
"nRF5" is also the name Nordic Semiconductor uses to describe
both the nrf51 and nrf52 chips.
Change-Id: I5f4e3f1ec780184b28ad44f735a746e68908c502
Signed-off-by: Slowcoder <slowcoder@gmail.com>
Reviewed-on: http://openocd.zylin.com/4209
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
IDs for STM32F722, F723, F413 and F423 added, handling of PCROP
for F722/723 and additional nWPRT bits for F413/423 implemented.
The additional protection bit positions for F413/423 conflict
with other options bits for the F7xx variants, additionally the
last two sectors share a common bit.
Protection for F413 and F767/777 now use protection blocks
rather sectors for dealing with protections bits.
Checking for halted state in 'lock' and 'unlock' removed: When
PCROP is activated in F723, halted state is not detected properly,
but lock/unlock sequence is required to disable PCROP.
Tested with STM32F723E-Disco, STM32F413ZH-Nucleo.
Change-Id: Ie6ddab47a9ae8461087d369b4f289b7f9d1e031c
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4045
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Change ftdi SWD driver and CMSIS-DAP to use it instead of LOG_DEBUG().
Change-Id: I17ba3de2086c7159209db61fba3faf067dfc5023
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3805
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Make 'offset' and 'length' parameters optional, if both are omitted
simply read the whole flash bank.
Additionally, check if the 'offset' and 'length' arguments are out of
bounds of the flash bank.
Change-Id: Ib9c1b0538a2c78ebcf702e2da11468dff407f8ff
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3862
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Make the 'offset' parameter optional, if omitted simply start at the
beginning of the flash bank.
Additionally, check if the argument is out of bounds of the flash bank.
Change-Id: I8e9632b539ad9e83211e1ac6a06da4c8109cbc60
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3860
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This device differs a lot from others in KL series.
Unfortunately the System Integration Module, where device
identification resides, moved to a new address so probe now have
to try both addresses of SIM_SDID.
Introduce a new bank creation option: -sim-base to ensure error free probe.
WDOG32 is slightly different from KE1x and on different address.
System Mode Controler changed layout to word aligned.
Change-Id: I2c9dca0c4ad4228fcc941d6078d15f5e394833ff
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/4059
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Kinetis flash driver services huge number of MCU types. They have
one, two or four flash banks with option of FlexNVM. It would
require ~36 config files just for Kx series, more for KLx, KVx and KE1x.
The change implements alternative approach:
- configuration file creates just one pflash bank (common for all devices)
- when a device is probed, additional pflash or flexnvm banks are created
based on flash layout of the connected MCU
- created banks have names with optional numbering e.g. kx.pflash0 kx.pflash1
kx.flexnvm0 kx.flexnvm1
- the first bank gets renamed if numbering is used
Automatic bank creation is enabled by tcl command 'kinetis create_banks'.
Used solution has a drawback: other banks than pflash0 are not accessible
until pflash0 is probed. Fortunately gdb attach and standard programming
accesses banks in right sequence.
Change-Id: I5b9037cbefdb8a4176b7715fbcc3af4da4c1ab60
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3925
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Config file renamed to ke0x.cfg and a notice added to texi.
While on ke0x.cfg CPUTAPID setting fixed: device has SWD port only, no JTAG.
Removed per device configs as they set CHIPNAME and nothing more.
Let's use reasonably universal chip name 'ke' set in family config.
Change-Id: I313db87a59f25f968eb3c27df155780b67becee8
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3897
Tested-by: jenkins
Reviewed-by: Ivan Meleca <ivan@artekit.eu>
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The new Kinetis KE1x families use FTFE flash controller unlike KE0x.
Also SDID coding corresponds to new K, KL and KV families.
That's why KE1x is handled by kinetis driver instead of kinetis_ke
Change-Id: Ibb73e28e41dfbb086e761e1f006b089825dab854
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3896
Tested-by: jenkins
Reviewed-by: Joakim Nohlgård <joakim.nohlgard@eistec.se>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Supported SoCs: AR71xx, AR724x, AR91xx, AR93xx, QCA9558
Extended and revised version of my original patch submitted by Dmytro
here: http://openocd.zylin.com/#/c/3390
This driver is using pure SPI mode, so the flash base address is not
used except some flash commands (e.g. "flash program") need it to
distinguish the banks.
Example config with all 3 chip selects:
flash bank flash0 ath79 0 0 0 0 $_TARGETNAME cs0
flash bank flash1 ath79 0x10000000 0 0 0 $_TARGETNAME cs1
flash bank flash2 ath79 0x20000000 0 0 0 $_TARGETNAME cs2
Example usage:
> flash probe flash0
Found flash device 'win w25q128fv' (ID 0x001840ef)
flash 'ath79' found at 0x00000000
> flash probe flash1
No SPI flash found
> flash probe flash2
No SPI flash found
> flash banks
> flash read_bank flash0 /tmp/test.bin 0x00000000 0x1000
reading 4096 bytes from flash @0x00000000
wrote 4096 bytes to file /tmp/test.bin from flash bank 0 at offset
0x00000000 in 28.688066s (0.139 KiB/s)
Change-Id: I5feb697722c07e83a9c1b361a9db7b06bc699aa8
Signed-off-by: Tobias Diedrich <ranma+openocd@tdiedrich.de>
Reviewed-on: http://openocd.zylin.com/3612
Tested-by: jenkins
Reviewed-by: Dmytro <dioptimizer@hotmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
For some targets (like nrf51) sysfs driver is too slow. This
patch implements memory maped driver for IMX processors.
Mostly based on bcm2835gpio. Tested on imx6ul CPU. However, it should
work on any NXP IMX CPU.
Change-Id: Idace4c98181c6e9c64dd158bfa52631204b5c4a7
Signed-off-by: Grzegorz Kostka <kostka.grzegorz@gmail.com>
Reviewed-on: http://openocd.zylin.com/4106
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds a driver for the SWD-only Cypress KitProg
programmer/debugger.
Change-Id: I3a9a8011a762781d560ebb305597e782a4f9a8e5
Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Reviewed-on: http://openocd.zylin.com/3221
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Make the 'offset' parameter optional, if omitted simply start at the
beginning of the flash bank.
Additionally, check if the argument is out of bounds of the flash bank.
Change-Id: Id1959eee5c395666c35f26342c3c50134dd564e5
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3858
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
document aarch64 specific commands and common ARMv7 and v8 DAP commands
Change-Id: Icbb76209735ec734f2e67f82bfc7270edb40ad0b
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/4008
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Commit 77a1c01ccb introduced infrastructure
for utilizing protection blocks of different size than erase sector.
Parts of doc/help kept reading 'sector' instead of 'protection block'.
flash_driver_protect() parameter range testing did not switched
to bank->num_prot_blocks.
This change fixes it.
Change-Id: Iec301761190a1a1bcc4cb005a519b9e5e4fede51
Reported-by: Mark Odell <mark@odell.ws>
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3917
Tested-by: jenkins
Reviewed-by: Mark Odell <mrfirmware@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Fix typo and a sentence that sounds strange since the ft2232 driver
was removed.
Add documentation for the SWD signal usage.
Remove the text mentioning a default VID:PID which doesn't exist.
Change-Id: I27eba571f2f7c46bdb6ae623ab285595018e99d9
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3935
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This is needed to generate PDF user manual without typesetting
artifacts.
Change-Id: Ibcbd804dac2b9415459327f53f6fad0dc38fa5c6
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3919
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
EMUCOM is a way to communicate with a J-Link device via so called
channels. A channel can either be read or written in a single
operation.
Beside the reserved channels for SEGGER, there are channels available to
implement vendor and/or device specific functionalities. For example,
EMUCOM is used on many starter and development kits from Silicon Labs to
access power measurements and various other information and settings.
Change-Id: I6094109c043b34aed4a40ceabe71f30ff896bf1d
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3794
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds a Cortex-M private configuration option
that allows setting the acess point during target
creation. This circumvents situations in hybrid systems
when the correct access point can not be automatically
detected.
Change-Id: If313a5250e6e66509bb9080f3498feab7781dced
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3639
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The Cypress CY7C65215 Dual Channel USB-Serial Bridge Controller [1]
understands the OpenJTAG protocol over a proprietary USB interface.
This patch adds support for the CY7C65215 to the openjtag interface
driver. A new configuration option, `openjtag_variant`, allows to
select the transport to use.
Libusb (1.x or 0.1) is now a hard dependency of the openjtag driver.
This should not be a big issue as libftdi also depends on it.
[1] http://www.cypress.com/?rID=82870
Change-Id: I55ffb3fd9e006eb311e405d9fb836bb119644bfd
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-on: http://openocd.zylin.com/2805
Tested-by: jenkins
Reviewed-by: Jiri Kastner <cz172638@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch adds support for bridging semihosting to GDB's File-I/O
remote protocol extension. For the most part operations match up 1:1,
however some require a working area to complete successfully, namely
operations that devolve to read, stat, and gettimeofday.
A new command was added to enable support for fileio named `arm
semihosting_fileio`, which ensures that the default behavior remains
intact for those that prefer it.
Finally, redundant logging was removed from the target_arch_state
function; this permits ARM targets to quiesce log output when polling
for a fileio reply. This prevents filling the logs with halt/resume
messages when using semihosting fileio.
Change-Id: Ifbb864fc2373336a501cc0332675b887b552e1ee
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3566
Tested-by: jenkins
Reviewed-by: Steven Stallion <sstallion@gmail.com>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This patch introduces RTOS support for uC/OS-III. Currently, only
FPU-less ARM Cortex-M targets are supported. Due to the configurability
of the RTOS, an OpenOCD-specific file must be linked along with the
project to determine the correct offsets within the OS_TCB structure.
In addition to the above, a crash was fixed in rtos_get_gdb_reg_list
such that RTOS support could be used between resets without restarting
OpenOCD and support for the Hg packet was cleaned up.
Change-Id: Ide004a689e6b886185df665c00fb644629eb31d1
Signed-off-by: Steven Stallion <stallion@squareup.com>
Reviewed-on: http://openocd.zylin.com/3556
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
This avoids the secondary binary search if the checksum is different
Change-Id: I986ba7687cea76f30e37a6bca58aabde18198263
Signed-off-by: Evan Hunter <ehunter@broadcom.com>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/2869
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
The '-defer-examine' option to target create allows declaring targets
that are present on the chain, but not fully functional. They will
be skipped by the initial arp_examine as well as arp_examine after
reset.
Manual examine using 'arp_examine' is needed to examine them, with the
idea that some kind of actions is neeed to bring them to a state where
examine will succeed (if at all possible).
In order to allow value less options to target command, I had to relax
the goi.argc check in jim_target_configure().
Change-Id: I9bf4e8d27eb6476dd9353d15f48965a8cfd5c122
Signed-off-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Reviewed-on: http://openocd.zylin.com/3076
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Purge all legacy interface configurations so there's no more confusion
over which one to use.
Also remove doc/INSTALL.txt which mentions ft2232 but otherwise just
duplicates what INSTALL says.
Change-Id: Ic94f808f123d4917e600b79309f1272c78a7bb11
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/3236
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Since OpenOCD doesn't fit most common definitions of the word "daemon",
using it in the documentation is confusing.
Reported by IRC user ohsix.
Change-Id: I688d722771b084b17c2a7af8e83fd64bab6141b8
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/3634
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
As per the documentation, used "disabled" as the value to disable, as this
is the same value to disable the telnet and tcl server.
Change-Id: Idc4a8580098ec1107dcc6e1f59e817ecdebc38ac
Signed-off-by: Sandeep Mistry <s.mistry@arduino.cc>
Reviewed-on: http://openocd.zylin.com/3175
Tested-by: jenkins
Reviewed-by: Cristian Maglie
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Kinetis family employs strange concept of Flash Configuration Field at
address 0x400 of program flash. Writing incorrect data to FCF may
permanently lock the device.
The change introduces 'kinetis fcf_source protection' mode. In this mode
write of flash image data to FCF is prevented. FCF data build from
protection (set by 'flash protect' command) are written instead.
FCF data are written also just after erase of relevant sector. It
protects device from locking security by reset or power cycle after erase.
prot_blocks array is used as protection blocks have bigger size than sectors.
Alignment and padding programming sections is rewritten to fix
writing with not section boundary aligned begin.
Change-Id: I9fc8bd37d6f627fb8ed7abb7f7560e78a740b195
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3562
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Originally flash/nor infrastructure assumed protection blocks identical
to erase sectors. This assumption is not valid for many flash types.
Driver code fixed the problem either by increasing sector size to
size of protection block or by defining more protection block than
really existed in device. Both cases had drawbacks.
The change retains compatibility with the old driver.
Updated driver can set protection blocks table independent
of sector table.
Change-Id: I27f6d267528ad9ed9fe0a85f05436a8ec17603a4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/3545
Tested-by: jenkins
Reviewed-by: Steven Stallion <stallion@squareup.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Paul Fertser
Tomas Vanek
Matej Kogovsek
Michele Sardo
Bohdan Tymkiv
Matthias Welwarsky
Robert Jordens
barthess
Spencer Oliver
Alexandre Torgue
Andreas Fritiofson
Slowcoder
Andreas Bolsch
Marc Schink
Tobias Diedrich
Grzegorz Kostka
Forest Crossman
Vianney le Clément de Saint-Marcq
Steven Stallion
Sandeep Mistry