from pre/post_reset event scripts. Adding the second parameter was
a mistake seen in retrospect. this gives precise control in post_reset
for *when* the post reset speed is set. The pre_reset event was
added *after* the second parameter to jtag_khz/speed
- the target implementations no longer gets involved in the reset mode
scheme. Either they reset a target into a halted mode or not.
target_process_reset()
detects if the reset halt failed or not.
- tcl target event names are now target_N_name. Mainly internal
at this early stage, but best to get the naming right now.
- added hardcoded reset modes from gdb_server.c. I don't know precisely what
these defaults should be or if it should be made configurable. Perhaps some
hardcoded defaults will do for now and it can be made configurable later.
- bugfix in cortex_m3.c for reset_run_and_xxx?
- issue syntax error upon obsolete argument in target command instead of
printing message that will surely drown in the log
git-svn-id: svn://svn.berlios.de/openocd/trunk@849 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This patch just uses the command.c interface to create tcl commands for the root level commands and avoids a bit of the "TCL" bleed into the rest of the openocd code.
Multilevel commands also supported.
git-svn-id: svn://svn.berlios.de/openocd/trunk@818 b42882b7-edfa-0310-969c-e2dbd0fdcd60
for a bit more info before I can tell with confidence whether or not
this would have any effect.
- worked on error propagation and output for flash
git-svn-id: svn://svn.berlios.de/openocd/trunk@539 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added new commands arm11 mrc and arm11 mcr to generate these instructions during debug
Thanks Michael Bruck
git-svn-id: svn://svn.berlios.de/openocd/trunk@477 b42882b7-edfa-0310-969c-e2dbd0fdcd60
arm11
--- Added burst memory transfer mode
This does not explicitly query command execution but rather uses a small
delay produced by the FT2232 on certain TAP commands.
A potential failure of this process is detected afterwards and the
program terminates with an error.
'arm11 memwrite burst disable'
can be used to switch this feature off.
'arm11 memwrite error_fatal disable'
can be used to prevent the program to exit on an memory write error
--- Added support for interrupt breaking via VCR register
Use 'arm11 vcr' command to set.
--- Cleaned up the handling of
halt/resume/step/poll, target->state, target->debug_reason,
target_call_event_callbacks() at least as far as I could guess the
intended behaviour from other targets.
Did some overall positive tests with GDB.
--- Added support for breakpoints
Hardware breakpoints only. All breakpoints will be treated as hardware
breakpoints.
All ARM11's seem to have at least 6 hardware breakpoints.
--- Stepping over BKPT added
Modification to PC without touching the target.
--- Stepping over a B or BL to self will do nothing
git-svn-id: svn://svn.berlios.de/openocd/trunk@385 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- make ep93xx and at91rm9200 bitbang JTAG interfaces dependant on ARM host (thanks to Vincent Palatin)
- various whitespace fixes
- removed various warnings
- add support for Debian GNU/kFreeBSD (thanks to Uwe Hermann)
- fix OpenOCD compilation for various platforms (thanks to Uwe Hermann and Vincent Palatin)
- switched order of JTAG chain examination and validation (examine first, then multiple validation tries even if examination failed)
- added target_request subsystem to handle requests from the target (debug messages and tracepoints implemented, future enhancements might include
semihosting, all ARM7/9 only for now)
- added support for GDB vFlashXXX packets (thanks to Pavel Chromy)
- added support for receiving data via ARM7/9 DCC
- reworked flash writing. the 'flash write' command is now deprecated and replaced by 'flash write_binary' (old syntax and behaviour) and 'flash
write_image' (write image files (bin, hex, elf, s19) to a target).
- added support for AMD/ST/SST 29F400B non-cfi flashes
git-svn-id: svn://svn.berlios.de/openocd/trunk@190 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- increase memory pseudo-image cache size to 1024 byte for improved trace analysis performance
- added OpenOCD+trace as an ETM capture driver example implementation
- new usbprog driver (thanks to Benedikt Sauter)
git-svn-id: svn://svn.berlios.de/openocd/trunk@186 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added support for usbprog (thanks to Benedikt Sauter)
- make OpenOCD listen for WM_QUIT messages on windows (thanks to Pavel Chromy)
- register at_exit handler to do necessary unregistering (thanks to Pavel Chromy)
- added dummy ETM capture driver to allow ETM to be registered without a capture driver
git-svn-id: svn://svn.berlios.de/openocd/trunk@180 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- reworked etm/etb into a generic etm part with trace capture drivers (currently only etb supported)
- added XScale debug handler binary to repository
- added Thumb disassembling (thanks to Vincent Palatin for this patch)
- added support for non-CFI compatible flashes to cfi driver (currently only SST39VFxxx devices supported)
This checkin is experimental, not suitable for general use
git-svn-id: svn://svn.berlios.de/openocd/trunk@155 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed some compiler warnigns in amt_jtagaccel.c, bitbang.c, parport.c
- free working area and register stuff if str7x block write algorithm failed
- check PC after exiting a target algorithm in armv4_5.c
git-svn-id: svn://svn.berlios.de/openocd/trunk@135 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed compiler warnings throughout the code (thanks to Vincent Palatin for this patch)
- added support for accessing ETB (embedded trace buffer) registers
git-svn-id: svn://svn.berlios.de/openocd/trunk@134 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed some small memory leaks (thanks to Spencer Oliver)
- verify chip- and buswidth of cfi flash configurations
- added support for ARM966E based systems (tested only with ST micro STR9, thanks to Spencer Oliver)
git-svn-id: svn://svn.berlios.de/openocd/trunk@81 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- OpenOCD now includes the ability to diassemble instructions on its own (only ARM for now, Thumb might follow).
The command is "armv4_5 disassemble <address> <count> ['thumb']" (thumb is currently unsupported).
I've compared the produced disassembly against GDB/GNU Objdump output, and it seems to be correct, but there may still be some bugs left.
git-svn-id: svn://svn.berlios.de/openocd/trunk@68 b42882b7-edfa-0310-969c-e2dbd0fdcd60
