Stick with the name "gdb_port" even if this command
can be used for other things(disable, named pipes,
anonymous stdin/out pipe). "port" is correct for
probably more than 90% of use cases, if not more.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This will allow switching to using named pipes.
Split this out as a seperate commit to make changes
easier to follow.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
depending on whether the connection is over a socket
or pipe, the read is done differently.
pipes can return -1 when writing 0 bytes, make 0 byte
writes a successful no-op. 0 byte writes falls out
naturally of tcl server code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
pipes have different fd's for in/out. This makes the
code more orthogonal and prepares for adding pipes.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
there was special support to support pressing 'x' to quit
openocd. ctrl-c is sufficient. The main server loop is already
complicated enough.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
There is an explicit command "log_output" that can
be used to redirect log output to a file, no need
for a hack in the first place.
Before enabling pipes, use "log_output foo" to redirect
log output to the "foo" files.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
ep93xx and at91rm9200 are conditionally built only on arm and were not
updated to reflect changes in command registration handler.
This patch makes them properly compile again, fixing a build failure
experienced on Debian armel.
Signed-off-by: Luca Bruno <lucab@debian.org>
Signed-off-by: Zachary T Welch <zwelch@codesourcery.com>
In previous patch, I have introduced again the symbol
"ocd_mem2array", now replaced by "mem2array".
Fix the error.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
short story: if the JTAG clock is too high, then the
behavior will be flaky and kludging the code may
seem to make things beter, but really it's just a red
herring.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
TCL procedures mrw and mmw, originally in DaVinci target code,
are duplicated in other TCL scripts.
Moved in a common helper file, and added help/usage description.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
capture of progress output would get polling
results. This will break in the example below
where polling output would override the tcl
return value.
capture {sleep 10000; set abc def}
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
by using ctrl-z instead of line end, multi-line tcl scripts
can be handled.
Testing: send ctrl-z a couple of times to make telnet enter the
mode where it sends ctrl-z unencoded.
Programs that talk to the tcl_server can send ctrl-z to
indicate end of tcl-let to be executed without having
to worry about telnet protocols.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
with this buffering disabled fancier logging scripts will
be able to process each line as it is output.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
used /dev/mem and mmem() to memory map JTAG registers
into user space and used new configure options to exclude
eCos specific code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone (again),
Watchpoints on xscale are quirky, so I thought a little explanation in the
user's manual was warranted.
Comments gratefully received.
Last one, Øyvind :-)
Thanks,
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Hi everyone,
A while back I sent in a patch that adds support for watchpoint lengths greater
than four on xscale. It's been working well, until the other day, when it
caused an unexpected debug exception. Looking into this I realized there is a
case where it breaks: when the length arg is greater than the base address.
This is a consequence of the way the hardware works. Don't see a work-around,
so I added code to xscale_add_watchpoint() to check for and disallow this
combination.
Some more detail... xscale watchpoint hardware does not support a length
directly. Instead, a mask value can be specified (not to be confused with the
optional mask arg to the wp command, which xscale does not support). Any bits
set in the mask are ignored when the watchpoint hardware compares the access
address to the watchpoint address. So as long as the length is a power of two,
setting the mask to length-1 effectively specifies the length. Or so I thought,
until I realized that if the length exceeds the base address, *all* bits of the
base address are ignored by the comaparator, and the watchpoint range
effectively becomes 0 .. length.
Questions, comments, criticisms gratefully received.
Thanks,
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Hi everyone,
Added more LOG_ERROR messsages to watchpoint and breakpoint code, given that the
infrastructure no longer interprets returned error codes. Also changed
existing LOG_INFO and LOG_WARNING to LOG_ERROR for cases where an error is
returned.
Note that the check of the target state is superflous, since the infrastruture
code currently checks this before calling target code. Is this being
reconsidered as well? Also, should we stop returning anything other than
ERROR_OK and ERROR_FAIL?
Comments gratefully received.
Thanks,
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
do not try to interpret "retval" into a string, just
amend a bit about the context of the already reported
error.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
the new Marvell PXA270M processor has a new TAPID: 0x89265013.
Attached you will find a patch for target/pxa270.cfg that will handle this.
I have also attached a board/colibri.cfg file to support the Colibri
PXA270 module by Toradex.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone,
Version 2 of this patch. Code added to breakpoints.c was removed from previous
patch, and item 3 added, per discussion with Øyvind regarding error reporting.
Item 4 added, which I just noticed.
I tried to use a software breakpoint in thumb code on the xscale for the first
time recently, and was surprised to find that it didn't work. The result was
this patch, which does four things:
1): fix trivial cut-n-paste error that caused thumb breakpoints to not work
2): call xscale_set_breakpoint() from xscale_add_breakpoint()
3): log error on data abort in xscale_write_memory()
4): fixed incorrect error code returned by xscale_set_breakpoint() when no
breakpoint register is available; added comment
Item 2 not only makes the xscale breakpoint code consistent with other targets,
but also alerts the user immediately if an error occurs when writing the
breakpoint instruction to target memory (previously, xscale_set_breakpoint() was
not called until execution resumed). Also, calling xscale_breakpoint_set() as
part of the call chain starting with handle_bp_command() and propagating the
return status back up the chain avoids the situation where OpenOCD "thinks" the
breakpoint is set when in reality an error ocurred.
Item 3 provides a helpful message for a common reason for failure to set sw
breakpoint.
This was thoroughly tested, mindful of the fact that breakpoint management is
somewhat dicey during single-stepping.
Comments and criticisms of course gratefully received.
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone,
I figured since I was poking around in the breakpoint code on other arches, I'd
add this change to those arches that don't do it already. This patch propagates
the return code of <arch>_set_breakpoint() up the call stack. This ensures that
the higher layer breakpoint infrastructure is aware that an error ocurred, in
which case the breakpoint is not recorded.
Normally I wouldn't touch code that I can't test, but the code is very
uniform across architectures, and the change is rather benign, so I figured
after careful inspection that it is safe. If the maintainers or others think
this is imprudent, the patch can be dropped.
Also changed the error code to something more appropriate in two cases where
hardware resources are unavailable.
Comments and criticisms of course gratefully received.
Mike
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
you can now set a variable in a script like set version [version].
Also version takes an optional argument "git" to show git version
of source. If git is not installed during the build, then this
will yield an error that is ignored during the build and "version git"
returns an empty string.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Commands that output progress output and no return value
will have the progress output captured.
Commands that do not output progress output(tcl commands)
will return the tcl return value instead.
The advantage here is that it is no longer necessary to
consider which command one is capturing, it works for
either.
Example #1: capture progress output:
set foo [capture help]
Example #2: capture tcl return value
set foo [capture {set abc def}]
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
for non_cfi cfi chips free() was invoked on rodata.
The mystery is why this bug has survived for so long.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
sizeof() is a bit less scary than seing assumption
about size of type, no bug as such.
Use NULL instead of 0 for pointers. More obvious that
it is a pointer from code inspection.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Hi everyone,
This simple patch fixes a problem I noticed on the xscale where incorrect values
are sometimes reported by the reg command. The problem can occur when
requesting the value of registers in the xscale-specific register cache. With a
couple of exceptions, none of the registers in the xscale register cache are
automatically retrieved on debug entry. This is probably fine, as they are
unlikely to be needed on a regular basis during a typical debug session, and
they can be retrieved when explicitly requested by name using the reg command.
The problem is that once this is done, the register remains marked as valid for
the remainder of the OpenOCD session, and the reg command will henceforth always
report the same value because it is obtained from the cache and is never again
retrieved from the debug handler on the target.
The fix is to mark all registers in the xscale register cache as invalid on
debug entry (before the two exceptions are retrieved), thus forcing retrieval
(when requested) from the target across resumptions in execution, and avoiding
the reporting of stale values.
Small addition change by Øyvind: change 'i' to unsigned to fix compiler
warning for xscale_debug_entry() fn.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
I a mail conversation with Øyvind we stated that speed may not be set at
all on case CLOCK_MODE_KHZ and CLOCK_MODE_RCLK. Also there isn't proper
error propagation adapter_khz_to_speed or jtag_rclk_to_speed.
So jtag_get_speed may need some rewrite for error propagation.
CC: Øyvind Harboe <oyvind.harboe@zylin.com>
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Do not fail startup if communication with target is
not possible.
OpenOCD supports launching without a target connected
or the target powered down.
The user will typically power up the target and issue
a "reset init" + load his application after OpenOCD
is started then.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Someone called David Carne popped up on IRC and offered a fix (as he's not
on this list so can;t post here). I am just passing it on. (thanx David)
10:54 < davidc__> Basically; the Numonyx M29W160ET has an incorrect CFI PRI
block; it describes the erase blocks backwards
10:54 < davidc__> the linked patch has a fixup for that part [really trivial]:
