Stick with the name "gdb_port" even if this command
can be used for other things(disable, named pipes,
anonymous stdin/out pipe). "port" is correct for
probably more than 90% of use cases, if not more.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This will allow switching to using named pipes.
Split this out as a seperate commit to make changes
easier to follow.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
depending on whether the connection is over a socket
or pipe, the read is done differently.
pipes can return -1 when writing 0 bytes, make 0 byte
writes a successful no-op. 0 byte writes falls out
naturally of tcl server code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
pipes have different fd's for in/out. This makes the
code more orthogonal and prepares for adding pipes.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The gdb server incorrectly reports the memory map if we have
multiple targets with multiple flash banks.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This warning was only reproducable with
Cygwin.
Cygwin now builds without warnings for the basic
case.
Signed-off-by: Oyvind Harboe <oyvind.harboe@zylin.com>
if step/continue fails, then the error should be
reported to the calling fn.
The calling fn decides if the connection has to be
aborted or if packet processing can continue.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
GDB and OpenOCD has two different error number
spaces and no mapping exists between them.
If a specific error number is to be reported
to GDB then this has to be done at the calling
site, rather than as a generic routine that
tries to map "retval" to GDB error number speak.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The gdb_memory_map cmd for example fell through and returned
ERROR_COMMAND_SYNTAX_ERROR on success - behaviour is now as expected.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
reproducable when "./configure --enable-maintainer-mode CFLAGS=-D_DEBUG_GDB_IO_"
Signed-off-by: Jun Ma <sync.jma@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This stops GDB from launching with an empty memory map,
making gdb load w/flashing fail for no obvious reason.
The error message points in the direction of the gdb-attach
event that can be set up to issue a halt or "reset init"
which will put GDB in a well defined stated upon attach
and thus have a robust flash autoprobe.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
by ack'ing memory writes immediately and reporting either
at next memory write or stepi/continue time. GDB will then
send off a new packet that is ready by the time the previous
packet has been written to target memory.
On faster adapters this can be as much as 10% improvement.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Rather than issuing a halt and then stepi/resume, just
wait for target to halt.
Issue a sterner warning via gdb console that any gdb
register changes will be ignored in this case.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Report each region of same-size sectors separately, instead of
incorrectly reporting that every sector has the same size.
This is a longstanding bug on NOR flash chips with non-uniform
sector sizes. It was largely hidden by other bugs in flash
handling. When some of those were recently fixed, this one was
exposed as a regression on str710.
[oyvind.harboe@zylin.com: update the loop to behave on str7 ]
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Put the memory map logic into its own subroutine.
This will make it a bit easier to package bugfixes,
and simplifies the query packet handling.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make most methods static; net minor object code shrink.
Likewise various data symbols; no net change.
Shrink some overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add a NOR flash mechanism where erase_address ranges can be padded
out to sector boundaries, triggering a diagnostic:
> flash erase_address 0x0001f980 16
address range 0x0001f980 .. 0x0001f98f is not sector-aligned
Command handler execution failed
in procedure 'flash' called at file "command.c", line 647
called at file "command.c", line 361
>
> flash erase_address pad 0x0001f980 16
Adding extra erase range, 0x0001f800 to 0x0001f97f
Adding extra erase range, 0x0001f990 to 0x0001fbff
erased address 0x0001f980 (length 16) in 0.095975s (0.163 kb/s)
>
This addresses what would otherwise be something of a functional
regression. An earlier version of the interface had a dangerous
problem: it would silently erase data outside the range it was
told to erase. Fixing that bug turned up some folk who relied on
that unsafe behavior. (The classic problem with interface bugs!)
Now they can get that behavior again. If they really need it,
just specify "pad".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It looks like a bugfix from normal breakpoints was not
copied over.
Do not use clever mathematics and assumptions to convert from
GDB enum for break/watchpoints to OpenOCD enum.
Drop connection upon unknown breakpoint type, this code path
was not really considered by the previous code I think.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add file comments to a few files. Make the GDB server use
more conventional (pointer-free) hex digit conversion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Specifically for the port commands, clarify that the number
is optional, and omitting it causes the current number to be
displayed.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The gdb_port command can be invoked during normal execution
to report the port used for gdb, whereas it was listed as
CONFIG stage only, which caused an error when excuting
it to return the reported error.
Also in line with the grander goal of making more commands
available during all "modes" (perhaps retiring config mode),
there is no particular reason to limit gdb_port to the
config stage.
Regression was introduced in:
b3bf1d12b2 aka
v0.4.0-rc1-32-gb3bf1d1
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Most commands are usable only at runtime; so don't bother saying
that, it's noise. Moreover, tokens like EXEC are cryptic. Be
more clear: highlight only the commands which may (also) be used
during the config stage, thus matching the docs more closely.
There are
- Configuration commands (per documentation)
- And also some commands that valid at *any* time.
Update the docs to note that "help" now shows this mode info.
This also highlighted a few mistakes in command configuration,
mostly commands listed as "valid at any time" which shouldn't
have been. This just fixes ones I noted when sanity testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's less accepting of signed char ... insisting that e.g. tolower()
not receive one as a parameter.
It's probably good to phase out such usage, given the number of bugs
that lurk in the vicinity (assumptions that char is unsigned), so fix
these even though such usage is actually legal.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Use a separate variable for iterating GDB service port numbers than
the one set by the user. Restores the behavior of returning the
original port number and only incrementing the port used on success.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "flash.h"
the following form should be used.
#include <flash/flash.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "target_request.h"
the following form should be used.
#include <target/target_request.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "register.h"
the following form should be used.
#include <target/register.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "image.h"
the following form should be used.
#include <target/image.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "breakpoints.h"
the following form should be used.
#include <target/breakpoints.h>
The exception is from .c files in the same directory.
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "jtag.h"
the following form should be used.
#include <jtag/jtag.h>
The exception is from .c files in the same directory.
Rework gdb_init to create flexible APIs (gdb_target_add_{one,all}) and
static helper (gdb_target_start) for starting GDB services. Eliminates
duplicated code and provides general mechanisms for adding GDB services.
The 'init' command is updated to call the new API, and later patches can
decouple its policy of adding all targets therein.
Provides the new capability to use both piped and TCP servers when
multiple targets are defined. The first target fills the pipe, and
others will be started on TCP ports (unless disabled, i.e. gdb_port=0).
Several of the sites now using target_type_name() really
ought to be using an instance-specific name. Create a
function called target_name(), accessing the instance's
own (command) name.
Use it in several places that really should be displaying
instance-specific names. Also in several places which
were already doing so, but which had no wrapper to call.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
There are two names that may matter on a per-target basis.
One is a per-instance name (for example, "at91sam7s.cpu").
The other is the name of its type (for example, "arm7tdmi"),
which is shared among multiple targets.
Currently target_get_name() returns the type name, which is
misleading and is rarely appropriate for target diagnostics.
Rename that as target_type_name().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Updates all command parsing of simple "enable" and "disable" arguments.
A few case in the tree use a tri-state or extended arguments, which
cannot use this simple macro.
Simlifies the xscale icache/dcache command handler logic.
No need to indirect from registered integers to pointers.
Just stash the pointers directly in the register struct,
and don't even bother registering.
This is a small code shrink, speeds register access just
a smidgeon, and gets rid of another rude exit() path.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Don't include "target.h" from more headers than necessary. This
avoids needless interdependencies and duplicated include paths.
Don't needlessly include it in source files, either.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
