Remove double readout of DCB_DHCSR in target poll. The return value
of the endreset event is handled and not ignored in target poll.
Change-Id: I8fe026418dadcf0b0dcbb09acee871ad950937a2
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/1181
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
SAM4L requires additional steps to be taken right after SYSRESETREQ is
issued in order to function robustly:
- CMSIS-DAP DAP driver needs to explicitly check for sticky bit
errors since it is possible for adapter to perform successful
write opration, report no errors and then, under the hood, do
some other things that will result in sticky bit being set.
- Debugger needs to wait for security system to finish
intialization and assert CDBGPWRUPACK before proceeding
This change is related to commit http://openocd.zylin.com/#/c/1995/
Change-Id: I741c95a809bfd60d930cec9482239e4796a62326
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-on: http://openocd.zylin.com/2088
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Andrey Yurovsky <yurovsky@gmail.com>
This is used for the emulated DCC channel which is only maintained as long
as target->dbg_msg_enabled is set. Skip the saving and restoring if not
enabled to save one dap_run() per core register access.
Note that we could've probably queued all core register accesses in the
same transaction if the armv7 register framework hadn't required
synchronous register accesses.
Change-Id: I4fe6d713261ee5db42422203eb63035fdcc48891
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1848
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This eliminates most of the warnings reported when building for
arm-none-eabi (newlib).
Hsiangkai, there're many similar warnings left in your nds32 files, I
didn't have the nerve to clean them all, probably you could pick it
up.
Change-Id: Id3bbe2ed2e3f1396290e55bea4c45068165a4810
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1674
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the fpb_enabled is not set then as part of cortex_m3_set_breakpoint we
enable the fpb, however we do not signal the fpb as being enabled.
This issue only effects the hla target as the current cortex_m code enables
the fpb during cortex_m3_endreset_event.
Change-Id: I44d3fc65916c131b7a226869dd16aed5afb441b4
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1634
Tested-by: jenkins
We changed the actual target name quite a while ago.
This changes the actual target function names/defines to also match
this change.
Change-Id: I4f22fb107636db2279865b45350c9c776e608a75
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1626
Tested-by: jenkins
Accessing one byte of memory using a 16-bit access is not well defined.
The current implementation is forgiving and rounds up, but it should not
be relied upon.
Also, I suspect this code might fail if the byte order differs between
target and host, but I have no way of verifying it so I left it as it is.
Change-Id: I8d6a511151a194ed419f141703201f0632d84fc8
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1657
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Now that we support the target description format we do not need
these hacks anymore, we can now tell gdb what registers we support.
Change-Id: Ie774231d296420b35efcf708bc4435475c87ff5e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1617
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
We already set cpsr in armv7m_build_reg_cache, so lets use it for all other
accesses to this field.
Change-Id: I19b3b21ecf1571bbea12e1be664845e6544f6fa1
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1539
Tested-by: jenkins
soft_reset_halt was only really intended for the older arm arch, eg. armv4/5.
Newer arch such as armv7m/mips do not need this as they have better alternatives.
Change-Id: Ifb360680b7e4bfa5365f3c79d82574bded952b45
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1442
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This file is used by all the Cortex-M family not just Cortex-M3.
Change-Id: Ie8680535b220c66bb8fcd862510407a46a73e8a0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1429
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This should cover all the cases when RESET_SRST_NO_GATING is set
without RESET_HAS_SRST. This might happen when RESET_SRST_NO_GATING is
automatically set by a target code (and not from tcl).
However, there're some other places (mips_m4k, arm7_9_common) where
adding RESET_SRST_PULLS_TRST would lead to trying to use SRST even if
it's not present. Currently it's impossible for the user to enable
that flag without enabling SRST.
Change-Id: Ib1c6f68feed0b8057d55afd5f260bb22ab332ced
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1405
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Rename cortex_m3 target to use a more correct cortex_m name.
This also adds a deprecated_name var so that older scripts issue a warning
to update the target name.
cfg files have also been updated to the new target name.
Change-Id: Ia8429f38e88da677249c5caa560c50f8ce56ea10
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1129
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Sometimes the target may have breakpoint registers set from a previous
debug session, we can either sync them or as we have chosen here clear them.
Change-Id: I439a623ebbf010246a70e5596d04aa7d546da731
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1363
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Remove dummy implementations from all targets except arm7_9 and mips, which
are the only ones with real implementations. Replace with a single default
implementation simply calling target_write_memory().
Change-Id: I9228104240bc0b50661be20bc7909713ccda2164
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1213
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This removes the armv7m::core_cache and uses the generic arm::core_cache.
Change-Id: If854281b31486cea8be005008f6a71a691b4c208
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/968
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This simplifies the armv7m_core_reg structure ready for the move to using
the generic struct arm_reg.
Change-Id: I8edb9d77cc54965d49cd2e754568ebcea4cf6964
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/967
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
To simplify things change over to using the generic core_mode struct rather
than maintaining a armv7m specific one.
Change-Id: Ibf32b785d896fef4f33307fabe0d8eb266f7086f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/966
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Watchpoints were not being enabled when the hl adapter target was resumed.
This effects both stlink and icdi interfaces.
Change-Id: Ia9f8a9415be97a467cd099b63b6bc9f7f37d0c0d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/931
Tested-by: jenkins
If we halt due to a breakpoint make sure that we do not remove it during a
step, only remove breakpoints we have created.
Change-Id: I060168e54e53637d4fbf3cbcf62072efdb353807
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/947
Tested-by: jenkins
This occurs when stepping past a breakpoint on a even address with
maskisr option set to auto
With -d3 the following log message appears in this case:
"Debug : Interrupt handlers didn't complete within time,
leaving target running"
Cause : Given a breakpoint is set on the lower half word and the PC is on
the upper half word. When another breakpoint is now set on the current PC
then resuming the core will not result in a break on the newly set
breakpoint. This has been observed on a STM32F1x, STM32F2x (CM3) but not
on a STM32F0x (CM0). It's not clear if this is a STM32F1/F2 only or a
general CM3 problem.
Change-Id: I384813f3bfdf935373b5e23cdb2d7f243c70cc00
Signed-off-by: Peter Horn <peter.horn@bluewin.ch>
Reviewed-on: http://openocd.zylin.com/864
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If the target does not support SYSRESETREQ we fall back to using VECTRESET.
This however does not reset the peripherals and we issue a warning to the user
to suggest using a reset-init script.
Also suggest that using hardware srst will give them the same functionality
as using SYSRESETREQ.
Change-Id: Ie1781c4b849fed66c52222e6539735537c879fb3
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/802
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Purely cosmetic but use the same style as Cortex-A target, this makes
searching refs easier.
Change-Id: I732ad9701f561e2312c5d191f5aaffd3a2f2393d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/731
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The ADIv5 spec guarentees that tar_autoincr_block will be 10bits.
Make this the default for Cortex-M family until we detect a Cortex-M3/M4,
we then change autoincrement to 12bits.
Change-Id: Ie8c89134aa036879bdd8a3c312cee9715dbc6913
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/730
Tested-by: jenkins
Reviewed-by: simon qian <simonqian.openocd@gmail.com>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
This enables us to better handle some of the low level functions that the
stlink does not support. It also enables us to share a few more of the
standard cortex_m3 functions if necessary.
Change-Id: I7a2c57450122012ec189245d8879d8967913e00e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/637
Tested-by: jenkins
Some targets support connecting while the target's srst is asserted.
Tested on stm32 family.
Change-Id: I9df43623025e37832155aeee7aa099b844b85f16
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/606
Tested-by: jenkins
Add swd_init_reset and swd_add_reset.
Add adapter_assert_reset and adapter_deassert_reset, and call them instead
of JTAG reset functions.
Change-Id: Ib2551c6fbb45513e0ae0dc331cfe3ee3f922298a
Signed-off-by: Simon Qian <simonqian.openocd@gmail.com>
Reviewed-on: http://openocd.zylin.com/526
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch determine all cpu types and not only
the cortex M3 and the stm32 target use the common
target examine function from the cortex_m sources.
Change-Id: If689dd994b3855284b927fc4b206f420cf32b6c7
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/511
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
arm7_9_prepare_reset_halt is long since gone and the functionality
is implemented in the target's assert_reset handler.
Change-Id: Ib03c730cb39d68e5e3bb42f92af13daf8074e4e2
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/515
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This move will enable use to share with regmaps with the stlink target.
Change-Id: If8f41c7c53323d5074cb22ec3440530c1e402004
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/377
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
we should have caught them all - hopefully.
Change-Id: I35435317fccaf5ad0216244d69f76db6857bb582
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/381
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Change this functions to make it accessible for other
target implementations.
Change-Id: Ib41fc793cfb4de5439af026c2e8b52e7a9507c85
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/278
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This rename is in preparation for cortex_m4 support.
Change-Id: Ic08c298ec6ed2aabc2c39db67191f68b3a51f550
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/147
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
