These events have been deprecated for a number of years, update any
remaining scripts to the new events.
Change-Id: Ic31ff388545ac8b3a500045699ca92c541b13f12
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/634
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Tested-by: jenkins
Reviewed-by: Bill Traynor <wmat@alphatroop.com>
This patch let openocd running and only close the gdb connection
on error.
Change-Id: Ifb88e16834b51207cc4c82210eab904ed8d30b71
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/523
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch fix the compare for the list size and the register index.
Change-Id: I36d5e078f57d2a9f7823cfdf0d537762e00f6929
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/516
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch checks the received register length with the local
configured register length and disconnect on a length missmatch.
Change-Id: I6b112c6b55a9ffb4526f582a384ffa91dc8b792f
Signed-off-by: Mathias K <kesmtp@freenet.de>
Reviewed-on: http://openocd.zylin.com/517
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
we should have caught them all - hopefully.
Change-Id: I35435317fccaf5ad0216244d69f76db6857bb582
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/381
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Lets be consistent and use strndup to allocate the debug buffer.
Change-Id: I535ad270ebfeae6e09d28372ab3749c822971223
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/245
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Compile error is encountered when _DEBUG_GDB_IO_ is set,
due to duplicate variables.
Fixed by renaming the variable.
Change-Id: I729c06e317fdb899142c9ceaf543b7f580088807
Signed-off-by: James Zhao <jamzhao@gmail.com>
Reviewed-on: http://openocd.zylin.com/243
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
The calculation for reg_packet_size in gdb_get_registers_packet() could
generate a wrong result in the case of multiple registers whose size is
not a multiple of 8.
The current calculation sums the sizes for all registers then rounds the result
up to the next multiple of 8.
Instead it should round each register size up individually and sum the results for all registers.
Change-Id: Idfb5e5eeee0e69a6889dbe9769c0bf17feacb63b
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/200
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
gdb_memory_map() correctly calculates the target specific number of flash banks, but then uses the total number (all targets) instead of the target specific number to construct its GDB response, causing a crash.
Change-Id: I3f8639b3e90303a59753ebe140ce4fff96fd5db0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/199
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
- works on Cortex-M3 with ThreadX and FreeRTOS
Compared to original patch a few nits were fixed:
- remove stricmp usage
- unsigned compare fix
- printf formatting fixes
- fixed a bug with overrunning a memory buffer allocated with malloc.
gdb connect can fail when the flash has not been probed.
During gdb connect, the flash layout is reported, but this
can not be automatically detected for a target that is
powered up and OpenOCD supports connecting to gdb server
even if the target is powered down.
The solution is to turn of the gdb_memory_map feature.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Stick with the name "gdb_port" even if this command
can be used for other things(disable, named pipes,
anonymous stdin/out pipe). "port" is correct for
probably more than 90% of use cases, if not more.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This will allow switching to using named pipes.
Split this out as a seperate commit to make changes
easier to follow.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
depending on whether the connection is over a socket
or pipe, the read is done differently.
pipes can return -1 when writing 0 bytes, make 0 byte
writes a successful no-op. 0 byte writes falls out
naturally of tcl server code.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
pipes have different fd's for in/out. This makes the
code more orthogonal and prepares for adding pipes.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The gdb server incorrectly reports the memory map if we have
multiple targets with multiple flash banks.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
This warning was only reproducable with
Cygwin.
Cygwin now builds without warnings for the basic
case.
Signed-off-by: Oyvind Harboe <oyvind.harboe@zylin.com>
if step/continue fails, then the error should be
reported to the calling fn.
The calling fn decides if the connection has to be
aborted or if packet processing can continue.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
GDB and OpenOCD has two different error number
spaces and no mapping exists between them.
If a specific error number is to be reported
to GDB then this has to be done at the calling
site, rather than as a generic routine that
tries to map "retval" to GDB error number speak.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
The gdb_memory_map cmd for example fell through and returned
ERROR_COMMAND_SYNTAX_ERROR on success - behaviour is now as expected.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
reproducable when "./configure --enable-maintainer-mode CFLAGS=-D_DEBUG_GDB_IO_"
Signed-off-by: Jun Ma <sync.jma@gmail.com>
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
This stops GDB from launching with an empty memory map,
making gdb load w/flashing fail for no obvious reason.
The error message points in the direction of the gdb-attach
event that can be set up to issue a halt or "reset init"
which will put GDB in a well defined stated upon attach
and thus have a robust flash autoprobe.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
by ack'ing memory writes immediately and reporting either
at next memory write or stepi/continue time. GDB will then
send off a new packet that is ready by the time the previous
packet has been written to target memory.
On faster adapters this can be as much as 10% improvement.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Rather than issuing a halt and then stepi/resume, just
wait for target to halt.
Issue a sterner warning via gdb console that any gdb
register changes will be ignored in this case.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Report each region of same-size sectors separately, instead of
incorrectly reporting that every sector has the same size.
This is a longstanding bug on NOR flash chips with non-uniform
sector sizes. It was largely hidden by other bugs in flash
handling. When some of those were recently fixed, this one was
exposed as a regression on str710.
[oyvind.harboe@zylin.com: update the loop to behave on str7 ]
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Put the memory map logic into its own subroutine.
This will make it a bit easier to package bugfixes,
and simplifies the query packet handling.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make most methods static; net minor object code shrink.
Likewise various data symbols; no net change.
Shrink some overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Add a NOR flash mechanism where erase_address ranges can be padded
out to sector boundaries, triggering a diagnostic:
> flash erase_address 0x0001f980 16
address range 0x0001f980 .. 0x0001f98f is not sector-aligned
Command handler execution failed
in procedure 'flash' called at file "command.c", line 647
called at file "command.c", line 361
>
> flash erase_address pad 0x0001f980 16
Adding extra erase range, 0x0001f800 to 0x0001f97f
Adding extra erase range, 0x0001f990 to 0x0001fbff
erased address 0x0001f980 (length 16) in 0.095975s (0.163 kb/s)
>
This addresses what would otherwise be something of a functional
regression. An earlier version of the interface had a dangerous
problem: it would silently erase data outside the range it was
told to erase. Fixing that bug turned up some folk who relied on
that unsafe behavior. (The classic problem with interface bugs!)
Now they can get that behavior again. If they really need it,
just specify "pad".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It looks like a bugfix from normal breakpoints was not
copied over.
Do not use clever mathematics and assumptions to convert from
GDB enum for break/watchpoints to OpenOCD enum.
Drop connection upon unknown breakpoint type, this code path
was not really considered by the previous code I think.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Add file comments to a few files. Make the GDB server use
more conventional (pointer-free) hex digit conversion.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make "usage" messages use the same EBNF as the User's Guide;
no angle brackets. Improve and correct various helptexts.
Specifically for the port commands, clarify that the number
is optional, and omitting it causes the current number to be
displayed.
Don't use "&function"; a function's name is its address.
Remove a couple instances of pointless whitespace; shrink a
few overlong lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The gdb_port command can be invoked during normal execution
to report the port used for gdb, whereas it was listed as
CONFIG stage only, which caused an error when excuting
it to return the reported error.
Also in line with the grander goal of making more commands
available during all "modes" (perhaps retiring config mode),
there is no particular reason to limit gdb_port to the
config stage.
Regression was introduced in:
b3bf1d12b2 aka
v0.4.0-rc1-32-gb3bf1d1
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
