Atmel introduced 6 new Cortex-M4 processors on 2011-10-26
SAM4S16C - 1024KB flash LQFP100/BGA100
SAM4S16B - 1024KB flash LQFP64/QFN64
SAM4S16A - 1024KB flash LQFP48/QFN48
SAM4S8C - 512KB flash LQFP100/BGA100
SAM4S8B - 512KB flash LQFP64/QFN64
SAM4S8A - 512KB flash LQFP48/QFN48
The SAM4S processors still suffer from the "6 waitstates needed
to program device" errata.
Other relevant changes are:
1. Address of flash memory starts at 0x400000.
2. EWP (Erase page and write page) only works for the first two 8KB "sectors"
3. Because of the EWP not working for all the sectors, normal page writes have
to be used. The default_flash_blank_check is used to check if lockregions
should be erased.
4. The EA (Erase All) command takes 7.3s to complete. (Previous timeout was
500 ms)
5. There are 128 lockable regions of 8KB each.
Implemented default blank checking, and page erase for load_image scenarios.
This is to compensate for the EWP flash commands only working on the
first 2 8KB sectors.
Change-Id: I7c5a52b177f7849a107611fd0f635fc416cfb724
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Reviewed-on: http://openocd.zylin.com/528
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
even the AT91EB40a's flash is covered by CFI and nobody ever submitted
any other drivers based on eCos code. It's just possible that this
idea was missing documentation and "marketing", but it's in git if
somebody wants to resurrect it.
Change-Id: I66449aa6e0997301f9d67f28098789bfc891d6e9
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Reviewed-on: http://openocd.zylin.com/502
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Use consistent names for the stm32 family flash drivers, eg.
stm32x -> stm32f1x
stm32f2xxx -> stm32f2x
this makes it easier to add support for newer stm32 families.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Use "git revert <commit>" to revert this commit, then build and
repair and post patch to the mailing list.
Warnings generated with:
nios2-elf-gcc (GCC) 3.4.6 (Altera Nios II 9.1 b222)
openocd/src/target/dsp5680xx.c: In function 'eonce_rx_upper_data':
openocd/src/target/dsp5680xx.c:252: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'eonce_rx_lower_data':
openocd/src/target/dsp5680xx.c:268: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'eonce_pc_store':
openocd/src/target/dsp5680xx.c:508: warning: dereferencing type-punned
pointer will break strict-aliasing rules
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_read':
openocd/src/target/dsp5680xx.c:736: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c:737: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_write_8':
openocd/src/target/dsp5680xx.c:823: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_write':
openocd/src/target/dsp5680xx.c:938: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c:941: warning: cast increases required
alignment of target type
openocd/src/target/dsp5680xx.c: In function 'dsp5680xx_f_wr':
openocd/src/target/dsp5680xx.c:1355: warning: cast increases required
alignment of target type
Hi,
I took the stm32x NOR flash driver and adapted it for the Ember EM357
chip. This chip is very similar to em351 and stm32w so the driver
should be easily extended to support those as well if anyone can get
their hands on some of those for testing.
changelog:
Added NOR flash driver em357
Best regards,
Erik Botö
Add support and documentation for STMicroelectronics
SPEAr Serial Memory Interface (SMI).
Code tested on SPEAr3xx only.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
This adds a virtual flash bank driver that allows virtual banks to
be defined that refer to an existing flash bank.
For example the real address for bank0 on the pic32 is 0x1fc00000
but the user program will either be in kseg0 (0xbfc00000) or
kseg1 (0x9fc00000).
This also means that gdb will be aware of all the read only flash
addresses.
Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
Move the bulk of the flash.h file into flash/nor/core.h, leaving an
empty husk that will be removed in the next patch.
The NOR driver structure is an implementation detail, so move it into
its own private header file <flash/nor/driver.h> along with helper
declaration for finding them by name.
Splits the exec mode commands out of flash.c into the flash/nor/ files.
The routines used by these high-level commands are moved into nor/core.c,
with their internal declarations placed in nor/imp.h.
Fixes distribution of <flash/nor/core.h> header.
The newly moved flash TCL routines access the internals of the module
too much. Fix the layering issues by adding new core NOR flash APIs:
<flash/nor/core.h>:
- flash_driver_find_by_name() - self-descriptive
<flash/nor/imp.h>:
- flash_bank_add() - encapsulates adding banks to bank list
- flash_bank_list() - encapsulates retreiving bank list
This allows the externs in flash/nor/imp.h to be removed, and
these mechanisms may now be re-used by other flash module code.
Moves the top-level 'flash' command handlers into flash/nor/tcl.c,
with flash/nor/imp.h providing an internal implementation header
to share non-public API components.
Includes the src directory in the search path, so header files may be
migrated from:
#include "foo.h"
to
#include <module/foo.h>
which is more conducive for installation.
