Build fixes: it failed abysmally with PPDEV enabled. Swapped
a build-time error with a FIXME comment in the affected macros.
Cleanup: remove "&" before function pointers, and excess indent,
for the interface struct declaration.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Rename DAP_IR_* as JTAG_DP_* since those symbols are specifically
for JTAG-DP (or SWJ-DP in JTAG mode), and won't work with SWD.
Define the JTAG ABORT and IDCODE instructions for completeness;
add a comment about where to (someday) use ABORT.
Fix messaging which assumes everything is an SWJ-DP; say "JTAG-DP"
instead, it's at least more appropriate for all JTAG transports.
Shrink the affected lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Fix: don't print the BASE address except if it's a MEM-AP;
that's an unlikely error, but there's no point getting it wrong.
Tweaks: comments, capitalization.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Make some private functions "static". Remove their public declarations,
and what is now an obviously unused function. Shrinks this object's size
(about 5% on x86_64) while making the code's scope easier to understand.
Shrink the affected lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Instead of magic numbers, use their AP_REG_* constants. Rename
the ROM address symbol as BASE to match ARM's documentation.
Comment various other symbols in the header; add some missing ones.
Remove an unused struct. Add some doxygen for stuff including the
DAP structure and initialization.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Shrink some lines, add some comments, simplify some tests.
During debug startup, log the core revision level too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most commands are usable only at runtime; so don't bother saying
that, it's noise. Moreover, tokens like EXEC are cryptic. Be
more clear: highlight only the commands which may (also) be used
during the config stage, thus matching the docs more closely.
There are
- Configuration commands (per documentation)
- And also some commands that valid at *any* time.
Update the docs to note that "help" now shows this mode info.
This also highlighted a few mistakes in command configuration,
mostly commands listed as "valid at any time" which shouldn't
have been. This just fixes ones I noted when sanity testing.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This makes it so that the usage/help command properly uses the whole command,
including subcommand, in the search for help information. This previously
caused erroneous output from the usage command handler.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
I wanted to make it so I can be ignorant of a commands invocation string, so
I tried to use CMD_CURRENT (aka cmd->current) which is supposed to house a
pointer to the current command. It turns out that this wasn't being set.
This patch adds the current command structure to the command invocation
structure before sending it along to the command handler.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The relevant cable config is already in OpenOCD, but not a config for
the JTAG adapter. I have tested with FlashLINK on ARM926.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This adds the .settings folder and the .cproject file put down
by Eclipse from the eyes of Git.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Handlers for commands
- arm7_9 semihosting <enable | disable>
- $_TARGETNAME arp_reset assert 1
didn't check if target has already been examined, and could
segfault when using the NULL pointer "arm7_9->eice_cache".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Remove useless space/tab at end of lines.
Remove spaces in indentation and replace with tab.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The handler for "arm9tdmi vector_catch ..." did not check
if target has already been examined. Without this fix it
segfaults when using NULL pointer "arm7_9->eice_cache".
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Print "ssize_t" as "%ld" (+ cast to long) not as "%zu".
Official MinGW (gcc 3.4.5) doesn't understand "z" flag.
Signed-off-by: Freddie Chopin <freddie_chopin@op.pl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Most of this patch updates documentation and comments for various
Luminary boards, supporting two bug fixes by helping to make sense
of the current mess:
- Recent rev C lm3s811 eval boards didn't work. They must use
the ICDI layout, which sets up some signals that the older
boards didn't need. This is actually safe and appropriate
for *all* recent boards ... so just make "luminary.cfg" use
the ICDI layout.
- "luminary-lm3s811.cfg", was previously unusable! No VID/PID;
and the wrong vendor string. Make it work, but reserve it
for older boards where the ICDI layout is wrong.
- Default the LM3748 eval board to "luminary.cfg", like the
other boards. If someone uses an external JTAG adapter, all
boards will use the same workaround (override that default).
The difference between the two FT2232 layouts is that eventually
the EVB layout will fail cleanly when asked to enable SWO trace,
but the ICDI layout will as cleanly be able to enable it. Folk
using "luminary.cfg" with Rev B boards won't see anything going
wrong until SWO support is (someday) added.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Otherwise the new alignment checking algorithm thinks that the
address is not aligned, because it is way beyond the last sector.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This config is only lightly tested, and doesn't work well yet;
but it's a start.
* Notably missing is PLL configuration, since each DaVinci
does that just a bit differently; and thus DDR2 setup.
* The SRST workaround needed for the goof in the CPLD's VHDL
depends on at least the not-yet-merged patch letting ARM9
(and ARM7) chips perform resets that don't use SRST.
So this isn't yet suitable for debugging U-Boot.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Resolve a regression when using newish automagic "write_image"
modes, by always padding to the end of affected sectors.
Also document some issues associated with those automagic options,
in the User's Guide and also some related code comments.
We might need similar padding at the *beginning* of some sectors,
but this is a minimalist fix for the problems which have currently
been reported (plus doc updates).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The 10-pin JTAG layout used with these adapters is used by
a variety of platforms including AVR.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This updates the board configuration for the SAM9-L9260 board with the
configuration for the on-board NAND and dataflash. Included are commands
for configuring the AT91SAM9 NAND flash driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
It's less accepting of signed char ... insisting that e.g. tolower()
not receive one as a parameter.
It's probably good to phase out such usage, given the number of bugs
that lurk in the vicinity (assumptions that char is unsigned), so fix
these even though such usage is actually legal.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Misc:
- Introduce some "struct reg" temporaries, for clarity
- Shorten lines
- Add some missing whitespace
- Clean up comments
- Add notes about some fault handling issues
- Most of these errata workarounds are for *OLD* chip revisions
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
And add my copyright. MPCore is untested, but it's the
only other ARM11 core to care about.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Command "reset halt" checks if PC properly resets, issueing warning:
"PC was not 0. Does this target need srst_pulls_trst?".
Checking PC against 0 is not always correct.
Removed PC value check, as suggested by Øyvind Harboe.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: U-PROPRIET-28D9DF\PROPRIETAIRE <PROPRIETAIRE@propriet-28d9df.(none)>
This creates the TCL interface for configuring an AT91SAM9 NAND flash
controller and implements the necessary functions to correctly work with
a NAND flash device connected to the chip. This includes updates to the
driver list and the Makefile.am to support building the driver and also
houses the documentation update in openocd.texi.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
In conjunction with manual register setup, this lets the ETM trigger
cause entry to debug state. It should make it easier to test and
bugfix the ETM code, by enabling non-trace usage and isolating bugs
specific to thef ETM support. (One current issue being that trace
data collection using the ETB doesn't yet behave.)
For example, many ARM9 cores with an ETM should be able to implement
four more (simple) breakpoints and two more (simple) watchpoints than
the EmbeddedICE supports. Or, they should be able to support complex
breakpoints, incorporating ETM sequencer, counters, and/or subroutine
entry/exit criteria int criteria used to trigger debug entry.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Change handling of the CYCLE_ACCURATE, BRANCH_OUTPUT, and
TRACE_* flags; also the CONTEXTID size values.
- Convert to symbols matching the actual register bits, instead of
some random *other* bits (and then correcting that abuse).
- Get rid of a now-needless enum.
- Keep those values in etm->control, and remove etm->tracemode.
These values all affect the trace data that's recorded by a trace
pod or in the ETB. I modified the file format used to dump ETB
data; since it's fairly clear nobody can use this mechanism now,
this can't cause anyone trouble.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
