- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
While at it, fix some coding style issues.
Change-Id: Id521394d89e0bf787a6f812701c2cc0fe7e4e63f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5919
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Define a target_addr_t type to support 32-bit and 64-bit addresses at
the same time. Also define matching TARGET_PRI*ADDR format macros as
well as a convenient TARGET_ADDR_FMT.
In targets that are 32-bit (avr32, nds32, arm7/9/11, fm4, xmc1000)
be least invasive by leaving the formatting unchanged apart from the
type;
for generic code adopt TARGET_ADDR_FMT as unified address format.
Don't silently change gdb formatting here, leave that to later.
Add COMMAND_PARSE_ADDRESS() macro to abstract the address type.
Implement it using its own parse_target_addr() function, in the hopes
of catching pointer type mismatches better.
Add '--disable-target64' configure option to revert to previous 32-bit
target address behavior.
Change-Id: I2e91d205862ceb14f94b3e72a7e99ee0373a85d5
Signed-off-by: Dongxue Zhang <elta.era@gmail.com>
Signed-off-by: David Ung <david.ung.42@gmail.com>
[AF: Default to enabling (Paul Fertser), rename macros, simplify]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Matthias Welwarsky <matthias.welwarsky@sysgo.com>
Also make GPL notices consistent according to:
https://www.gnu.org/licenses/gpl-howto.html
Change-Id: I84c9df40a774958a7ed91460c5d931cfab9f45ba
Signed-off-by: Marc Schink <openocd-dev@marcschink.de>
Reviewed-on: http://openocd.zylin.com/3488
Tested-by: jenkins
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
v2:
- Split work into separate patches
The received packet will not be altered in any of the processing functions.
Some it can be made "const".
Change-Id: I7bb410224cf6daa74a6c494624176ccb9ae638ac
Signed-off-by: Christian Eggers <ceggers@gmx.de>
Reviewed-on: http://openocd.zylin.com/1919
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Fixes bug that prevented users from specifying a base address of
0x80000000 or higher in image commands (flash write_image, etm image,
xscale trace_image).
image.base_address is an offset from the start address contained in
the image file (if there is one), or from 0 (for binary files). As a
signed 32-bit int, it couldn't be greater than 0x7fffffff, which is a
problem when trying to write a binary file to flash above that
address. Changing it to a 64-bit long long keeps it as a signed
offset, but allows it to cover the entire 32-bit address space.
Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>
Changes from the flat namespace to heirarchical one. Instead of writing:
#include "fileio.h"
the following form should be used.
#include <helper/fileio.h>
The exception is from .c files in the same directory.
Use size_t instead of uint32_t when specifying file sizes. Update all
consumers up through the layers to use size_t when required. These
changes should be safe, but the higher-levels will need to be updated
further to receive the intended benefits (i.e. large file support).
Add error checking for fileio_read and file_write. Previously, all
errors were being silently ignored, so this change might cause some
problems for some people in some cases. However, it gives us the chance
to handle any errors that do occur at higher-levels, rather than burying
our heads in the sand.
Add 'const' keyword to 'char *' parameters to allow command handlers to
pass constant string arguments. These changes allow the 'args' command
handler to be changed to 'const' in a subsequent patch.
The Hex parser uses a fixed number of sections. When the
number of sections in the file is greater than that, the
stack get corrupted and a CHECKSUM ERROR is detected
which is very confusing.
This checks the number of sections read, and increases
IMAGE_MAX_SECTIONS so it works on my file.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
- cleaned up headers to match rest of code
- added missing svn props for previously added files
git-svn-id: svn://svn.berlios.de/openocd/trunk@987 b42882b7-edfa-0310-969c-e2dbd0fdcd60
More precise, less code.
- removed unused code in fileio.c
- Windows should now find debug_handler.bin
git-svn-id: svn://svn.berlios.de/openocd/trunk@390 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- adds support for the Altium universal JTAG cable
- adds support for "wiggler2" cable (basically a wiggler with added LED, documentation coming soon)
- adds LED support. The LED is turned on during data transfer - works fine on Altium and wiggler2.
- adds PORT_EXIT pattern that is written to port when exiting, in order to turn off power on cables that get their power from parallel port data lines
- move port writes (with the system-specific ifdefs) to one central function
- increased image cache size to 2KB (might require more adaptive cache handling, e.g. LRU)
git-svn-id: svn://svn.berlios.de/openocd/trunk@204 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- make ep93xx and at91rm9200 bitbang JTAG interfaces dependant on ARM host (thanks to Vincent Palatin)
- various whitespace fixes
- removed various warnings
- add support for Debian GNU/kFreeBSD (thanks to Uwe Hermann)
- fix OpenOCD compilation for various platforms (thanks to Uwe Hermann and Vincent Palatin)
- switched order of JTAG chain examination and validation (examine first, then multiple validation tries even if examination failed)
- added target_request subsystem to handle requests from the target (debug messages and tracepoints implemented, future enhancements might include
semihosting, all ARM7/9 only for now)
- added support for GDB vFlashXXX packets (thanks to Pavel Chromy)
- added support for receiving data via ARM7/9 DCC
- reworked flash writing. the 'flash write' command is now deprecated and replaced by 'flash write_binary' (old syntax and behaviour) and 'flash
write_image' (write image files (bin, hex, elf, s19) to a target).
- added support for AMD/ST/SST 29F400B non-cfi flashes
git-svn-id: svn://svn.berlios.de/openocd/trunk@190 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- increase memory pseudo-image cache size to 1024 byte for improved trace analysis performance
- added OpenOCD+trace as an ETM capture driver example implementation
- new usbprog driver (thanks to Benedikt Sauter)
git-svn-id: svn://svn.berlios.de/openocd/trunk@186 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- added str9x programming using flash controller tap (str9xpec), including option bytes and device lock/unlock
- inttypes.h now used for long long printf style declarations
git-svn-id: svn://svn.berlios.de/openocd/trunk@174 b42882b7-edfa-0310-969c-e2dbd0fdcd60
- fixed bug in ARM926EJ-S cache handling that caused cache linefills to be disabled after first debug entry
- added support for auto image type detection (thanks to Vincent Palatin)
- further work on ETM trace decoding (tested with a ETB interface using an ETM in normal 16-bit port mode, still experimental)
git-svn-id: svn://svn.berlios.de/openocd/trunk@169 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This checkin is still experimental, not recommended for general use
git-svn-id: svn://svn.berlios.de/openocd/trunk@159 b42882b7-edfa-0310-969c-e2dbd0fdcd60
