Without the explicit dir at the end the repository will be cloned to "code".
Change-Id: Icd8b55b4ba74f23b214c3844e2fb785377768119
Signed-off-by: Freddie Chopin <freddie.chopin@gmail.com>
Reviewed-on: http://openocd.zylin.com/1349
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Tested-by: jenkins
As requested, here is the target configuration that I'm using for an
STLink-V2-attached STM32W108C8. For some reason, it only seems to work
with "reset_config trst_only".
Change-Id: Icbff4f83343e1f505d8afdfc53ff6f8b7496cac9
Signed-off-by: Ben Nahill <bnahill@gmail.com>
Reviewed-on: http://openocd.zylin.com/1347
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The em357 driver only supported one page configuration (192k in 96 2048k)
pages. This is fine for em357 chips since that's the size they have, but
ST's STM32W chips (pretty much the same) have different flash
configurations available (64, 128, 192, 256k). I can't find anywhere
that would indicate the size of the chip anywhere in memory so the
selection must be manual, using the 'size' parameter. For backwards
compatibility, any size not known to be in use defaults to the 192k
configuration. I don't have any em357 devices to test, but I also found
that I had to re-assert the FPEC clock enable before performing an
erase. This is a single line and shouldn't break any configurations.
My testing so far has only been with a 64k device with 8k of RAM.
Change-Id: Ic0ac400a9696efaa09d1407dd4a4d456bc2c318b
Signed-off-by: Ben Nahill <bnahill@gmail.com>
Reviewed-on: http://openocd.zylin.com/1336
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
Disable polling the target before we issue a 'reset run'. This stops errors or
warnings if the target disables the SWD or JTAG interface as part of the
application code.
Change-Id: I5019dffdad41a8e210003ece1caf89069ee0f223
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1331
Tested-by: jenkins
We need to make sure that srst is asserted before we attempt to switch into
jtag or swd mode otherwise we receive a error (-9) - invalid device id.
Change-Id: I625166c751cfba8e8a5290f40122bb9afc9dbb39
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1315
Tested-by: jenkins
If parport_toggling_time is called before the adapter speed has been
configured then the call fails. Probably not the best fix, but does at least
enable parport_toggling_time to be used again.
This regression was added in commit 740b9e25b4
Change-Id: I90300916d6bda5ef053c557e5ac136c4f002bdd1
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1309
Tested-by: jenkins
Update to latest jimtcl commit 2c1eba991e21a6f0b531fb0f83e21f9e6ee7c515.
This fixes issues when building on certain versions of Mac OSX.
Change-Id: I551477752d7913c84e6deb60b889d0c14bd200a0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1311
Tested-by: jenkins
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
The final bit was incorrectly added as output data, even if no data was
to be written. Changed it to match handling of other bits.
Change-Id: I91e5ba0c932876bfb579c22e6c7ef0300baa1534
Signed-off-by: Yann Vernier <yann.vernier@orsoc.se>
Reviewed-on: http://openocd.zylin.com/1049
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add command to fix CSW_SPROT in register AP_CSW.
This solves dap apmem access in non secure access.
Change-Id: I7cfcb6434d75f5cfd4a2630a059901cdeea010ce
Signed-off-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Reviewed-on: http://openocd.zylin.com/1276
Tested-by: jenkins
Reviewed-by: mike brown
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
After calling mips32_cp0_read() nothing has been queued, the call to jtag_exec_queue() is unnecessary.
Change-Id: Ie25438045a8e9b6b1b170df7b52609d45f284b5a
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1190
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In current devel code there are 3 functions (related to m4k code) that need to restore register 8 from pracc stack:
mips32_pracc_read_u32()
mips32_cp0_read()
mips32_pracc_write_mem_generic()
And mips32_pracc_read_mem() needs to restore regs 8 and 9 from pracc stack.
Values in this registers should be the same as read by mips32_pracc_read_regs() when entering debug
mode and can be modified by mips32_pracc_write_regs() when leaving debug mode.
There is no need to read their values from the processor registers every time.
The fields reg8 and reg9 are added to struct mips_ejtag to store these register values
and the call to mips32_save_context() is shifted in mips_m4k_debug_entry() in order
to store them before any other function needs to restore these registers.
For the same reason in function mips_m4k_step() the call to mips_m4k_set_breakpoint(), if needed,
should be made after calling mips_m4k_debug_entry().
For single word write the number of pracc accesses are now 9 or 8, from 13 or 12 in current code,
single word read takes now 10 instead of 12.
This patch is really the first in a set of patches for an alternate m4k pracc code
much faster that current code. At least for me with pic32mx works fine.
Change-Id: Ibd9df5e8b9f78ce05a180949ba6a561c761b61d6
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1146
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In this function after loading the handler code and the jump code there is a call
to wait_for_pracc_rw() to verify that a pracc access is pending.
Next the address is read to verify that the handler is running, the address should be at
fastdata area.
Next, another call is made to wait_for_pracc_rw(). This call is not needed, we now already
that a pracc access is pending.
Better we call this function before loading the end address to be sure it is loaded correctly.
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Change-Id: If311450ea634786fc28cf1a8e18ed24ce5257d20
Reviewed-on: http://openocd.zylin.com/1142
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
By default pic32mx starts after any reset with 1 wait state for RAM access/exec.
It can be changed to 0 wait states by clearing the BMXWSDRM bit (bit 6) in BMXCON register.
With 0 wait states near doubles the execution speed. CRC check sum can be done much faster
increasing verify_image speed. Fast data transfer also works with a bit higher scan rate, up to 1500 Khz.
This option can be set at any time with
mww 0xbf882004 0x40
or cleared with
mww 0xbf882008 0x40.
Some numbers for FTDI/HS with current devel code and a elf file:
Core clock / wait states verify_image speed
------------------------------------|------------------------------
4 Mhz / 1 21 KiB/s
4 Mhz / 0 36 KiB/s
8 Mhz / 1 37 KiB/s
8 Mhz / 0 57 KiB/s
Change-Id: I4092ad0f3753f72f77108718d0ed3a3ab84e3b23
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1141
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Xiaofan <xiaofanc@gmail.com>
To show up the fail try to step with the core clock set to 31.25Khz
and with a ftdi/hs adapter or with a wiggler, -not with ft2232-.
The scan frequency should be set to 300Khz or higher, at lower frequency probably will not fail.
The code exits with error because the pracc address is at 0x0.
It also fails when using the "all" register, but in this case the code works without any message because the
pracc address is at 0xff202004 when it fails.
I never saw this fail with the core clock set to 500Khz or higher, but ...
The workaround simply puts a 1 ms delay after the execution of the DERET instruction.
Change-Id: I38e8c01a9c39aedd3282140543b83a0844d8ad29
Signed-off-by: Salvador Arroyo <sarroyofdez@yahoo.es>
Reviewed-on: http://openocd.zylin.com/1139
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Added support for ARMv7-M targets in arm_nandwrite and
arm_nandread.
Change-Id: Iab1d78d401f735e191c6a8519f3619035a300fae
Signed-off-by: Henrik Nilsson <henrik.nilsson@bytequest.se>
Reviewed-on: http://openocd.zylin.com/1188
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
Fixes system hang for devices that don't ignore
transactions to bad addresses.
Change-Id: Ia98344d7efc12951ef79dbc82b8f792b70a22cee
Signed-off-by: Evan Hunter <ehunter@broadcom.com>
Reviewed-on: http://openocd.zylin.com/1115
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Moved JTAG code out of transport-neutral file (arm_adi_v5.c) into
transport specific file (adi_v5_jtag.c).
Added ap_block_read to dap_ops interface (arm_adi_v5.h) to support
the move.
Change-Id: I796d3984f138aad052b97c77ac9c12ffd1158f74
Signed-off-by: mike brown <mike@theshedworks.org.uk>
Reviewed-on: http://openocd.zylin.com/1277
Tested-by: jenkins
Reviewed-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
These were missed when git was moved to the new SF platform during Nov 2012.
Change-Id: I7b4ae9dea010d95f9bf4c26841b5b724f41768be
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1248
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Tested-by: jenkins
makeinfo has a long outstanding bug that means @anchors are not correctly
formatted for split html, see:
http://lists.gnu.org/archive/html/bug-texinfo/2012-06/msg00000.html
The issue relates to using spaces or hyphens in the @anchor name.
Issue also reported via Trac #44
Change-Id: Id72e23375dd167674b2ae5b314e8242b90a72a5f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1244
Tested-by: jenkins
Reviewed-by: Freddie Chopin <freddie.chopin@gmail.com>
The command 'at91sam3 info' ignores PLLA DIV values >1. This patch fixes it.
Tested on a SAM3S4C chip.
Change-Id: I051f41bb3dcefe1ac785fbcb48477a807daa16a2
Signed-off-by: Thomas Schmid <thomas.schmid@gmail.com>
Reviewed-on: http://openocd.zylin.com/1307
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
The commit "gdbserver: use common hexify/unhexify routines" [3d62c3d]
mis-replaced a call to "str_to_hex" with a call to "unhexify". "hexify"
should have been used instead.
Change-Id: I5f5904b1b422f819a6308e2c0740ea43d22c7d0b
Signed-off-by: Christian Gudrian <christian.gudrian@gmx.de>
Reviewed-on: http://openocd.zylin.com/1308
Tested-by: jenkins
Reviewed-by: Peter Stuge <peter@stuge.se>
This regression was caused due to the recent addition of R4 support and
the removal of the bulk_write_memory handler.
Change-Id: Ide692737f235c0e9906becb6f3502ba52c5907aa
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1246
Tested-by: jenkins
The only caller was arm_nandwrite(). Replace that call with
target_write_buffer() instead, which in turn may end up calling the same
bulk_write_memory target API function.
Change-Id: If34c7474df5cf14af3b732fb4774816818f28e79
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1214
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Remove dummy implementations from all targets except arm7_9 and mips, which
are the only ones with real implementations. Replace with a single default
implementation simply calling target_write_memory().
Change-Id: I9228104240bc0b50661be20bc7909713ccda2164
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1213
Tested-by: jenkins
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This patch adds support for usbprog-jtag and usbvlab that are mostly compatible
to opendous except for IN and OUT endpoints and usb transfer mode.
Change-Id: I44557c2449fe7473295038efa6ae4fc8d80ec7bf
Signed-off-by: Stefan Mahr <stefan.mahr@sphairon.com>
Reviewed-on: http://openocd.zylin.com/687
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
usb_blaster_device_desc was allocated, but never freed.
Change-Id: I764bd092c71b8c260b98aab0e7a1710fd7bfa9fd
Signed-off-by: Stefan Mahr <stefan.mahr@sphairon.com>
Reviewed-on: http://openocd.zylin.com/1224
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Tested-by: jenkins
If command parport_cable is not executed, parport_cable points to
const char array in read-only memory as default. On exit free()
will try to free this read-only memory. This patch uses strdup to
allocate memory when defining default setting.
Change-Id: I290e707ac6a37e9dc1b45c85ca51d8bd6aac6761
Signed-off-by: Stefan Mahr <stefan.mahr@sphairon.com>
Reviewed-on: http://openocd.zylin.com/1223
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Appending bits to TAP buffer doesn't check if there's enough space left.
This patch adds this check to fix TAP overflow error.
Change-Id: If80d5ab4a24983ad24f3cab31f9676d1590ebf5d
Signed-off-by: Stefan Mahr <stefan.mahr@sphairon.com>
Reviewed-on: http://openocd.zylin.com/1216
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
It was listed in the ft2232 based cables supported. Moreover, the
ft2232_channel option, which was added to support this cable, was explained.
Change-Id: I82ebc7bc10d6472f96ab150e78d623a617edccd2
Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar>
Reviewed-on: http://openocd.zylin.com/1098
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
This config file add support to the opendous cable based on the chip ft2232H,
using the ft2232 interface driver.
Change-Id: I8171a0c475af8d61e081844ee86466a392138fb0
Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar>
Reviewed-on: http://openocd.zylin.com/1096
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
With this option a different channel of the ft2232 chip can be selected using
a previously existing layout. It was made for a partner called Salvador
Tropea.
Change-Id: Ia0dedb2f50e232d089e73788735edc8f47ee23e6
Signed-off-by: Rodrigo Melo <rmelo@inti.gob.ar>
Reviewed-on: http://openocd.zylin.com/1095
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The kinetis datasheets specify the flash registers as bytes rather
than as words, as the previous implementation did. This also makes
a few code sections slightly less endian-magical.
Change-Id: If8f4adfc7f4341085ae5b6eacbf7d74bbd74cf08
Signed-off-by: Alex Austin <alex.austin@spectrumdsi.com>
Reviewed-on: http://openocd.zylin.com/1192
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add url to show where the http password is configured.
Also add note that password can also be saved to url git config.
Change-Id: I3c1a022580e5f73372b0c50e8d1d2f0b1498966f
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1207
Tested-by: jenkins
This adds a program proc that simplifies using OpenOCD as a standalone
programmer.
Change-Id: I6ece492cd878c170b734e8bb2e09fe8c4557d5a6
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1199
Tested-by: jenkins
Reviewed-by: Jörg Fischer <turboj@gmx.de>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Øyvind Harboe <oyvindharboe@gmail.com>
Freddie Chopin
Ben Nahill
Spencer Oliver
Andreas Fritiofson
Peter Dietzsch
Yann Vernier
Michel JAOUEN
Salvador Arroyo
Henrik Nilsson
Evan Hunter
mike brown
Thomas Schmid
Christian Gudrian
Stefan Mahr
Rodrigo Melo
Drasko DRASKOVIC
Alex Austin
Øyvind Harboe