We changed the actual target name quite a while ago.
This changes the actual target function names/defines to also match
this change.
Change-Id: I4f22fb107636db2279865b45350c9c776e608a75
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1626
Tested-by: jenkins
Create a single pair of relatively simple functions to handle all variants
of MEM-AP transfers. This replaces the many separate functions that
handled different access sizes and packed or non-packed transfers, which
were all implemented rather differently.
With this single implementation, performance should be more consistent,
regardless of transfer type.
Change-Id: I89960e437fc6ba68a389c074fab8eac91abcf844
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1658
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Accessing one byte of memory using a 16-bit access is not well defined.
The current implementation is forgiving and rounds up, but it should not
be relied upon.
Also, I suspect this code might fail if the byte order differs between
target and host, but I have no way of verifying it so I left it as it is.
Change-Id: I8d6a511151a194ed419f141703201f0632d84fc8
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1657
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The word count returned from max_tar_block_size() was compared with the
count of half-word/bytes in the u16 and u8 packed access functions,
causing an infinite loop if the access actually crossed the boundary.
Change max_tar_block_size() to return a byte count, and scale at the call
site.
Change-Id: I2fe9b5941eb485f3d8219cfdd29fb71e02006de4
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1649
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
For packed and/or unaligned accesses, the write functions reordered the
source buffer in place. Causing in the best case a segfault, in the worst
case silent data corruption.
Rewrite the data fetching to directly match the byte lane mapping
according to IHI0031C, without destroying the buffer.
Also slightly clean up variable usage and harmonize all the write
functions.
Change-Id: I9a01cfc5578653f9ec02043ff6b61a7a20f90d67
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1646
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Add support for OpenRISC target. This implementation
supports the adv_debug_sys debug unit core. The mohor
dbg_if is not supported. Support for mohor TAP core
and Altera Virtual JTAG core are also provided.
Change-Id: I3b1cfab1bbb28e497c4fca6ed1bd3a4362609b72
Signed-off-by: Franck Jullien <franck.jullien@gmail.com>
Reviewed-on: http://openocd.zylin.com/1547
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
It's been like this since the check was added, in 5aa93a5e.
Change-Id: Iaa0586e0cd1ce57ad92735dcc3e51108a133fe96
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1640
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Due to issues reported when using the jtag mode of the stlink (see Trac #61),
the functionality/checking has been moved to the driver.
This change also fixes unaligned 32bit memory read/write for the stlink.
From testing this change also brings a 3KiB/s speed increase, this is due
to the larger read/write packets.
Change-Id: I8234110e7e49a683f4dadd54c442ecdc3c47b320
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1632
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
This is the first part in moving the adapter specific api back into the
driver.
The next task is to also move the hla read/write buffer size handling.
Change-Id: I86a19144b50b6de18659bfcd05b3729b2cafc051
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1621
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Now that we support the target description format we do not need
these hacks anymore, we can now tell gdb what registers we support.
Change-Id: Ie774231d296420b35efcf708bc4435475c87ff5e
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1617
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Add support for the default gdb register description type "int" and "float".
When this is given to gdb it will use the bitsize to determine the reg size.
Change-Id: Iaeed594d1feece54044128eae1baff9858bdcae0
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1622
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Half-word and byte writes using mwh/mwb has been completely broken since
bf71e34cbf, because it dispatched all writes, regardless of access size,
to target_write_buffer(), which uses as large accesses as possible.
Partially revert the commit by changing back to the correct write method.
Change-Id: I60731fc576bf4a076a7da02bee7879e121c21d17
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1628
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Currently we try and use MEM-AP packed transfers as much as possible for
8/16bit transfers. However not all targets support packed transfers, so
check before using.
Change-Id: I66256007f25ccd0c583f23db5acf6d1aa8b5e57d
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1602
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
.soft_reset_halt is not necessary for nds32 target.
Remove the dependency.
Change-Id: Ic3b126d6c7eb995583a661b762627e736222fcaa
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1612
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
As GDB uses file-I/O protocol to access memory, use DMA to access
if no DCache. This commit improves the performance of Andes
Virtual Hosting.
Change-Id: I36bb2154b9f497fc4237625836cf8c7115330a60
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1580
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Modify handle_nds32_memory_access_command: do not use DCache
setting to block user's setting.
Change-Id: I2d33f893773e2a2e3e2f26edde5938ef5902609d
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1579
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
If multiple read watchpoints are hit at the same time, report
any one of these hit watchpoints.
Change-Id: I8d4439aa80e4b62bb7d48bbdc0450920e2008a2e
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1576
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Do not turn on/off polling as leave/enter debug mode.
Enable polling after gdb attached, and disable polling
after gdb detached.
Change-Id: Id64459b86f44937af7ea5ccfe2cd13e31732eecf
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1574
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
1. gprof uses 2-bytes as minimum bucket size.
2. As user wants to use gprof --sum to summarize multiple
profiling data files, the range MUST be the same.
Add new arguments to specify profiling range.
Change-Id: Ie7e6afa6a4d82250e2d194a0eed2b428c1479ea1
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1572
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Profiling could be target-specific. Add .profiling interface
to target_type.
Change-Id: Ic0eea9db742971db1350a474fbbb5ed24565922b
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1571
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
I do not know what is the reasonable number of buckets.
If there are enough buckets, the result will be accurate.
I propose increase the maximum number of buckets to 128K.
If the size of program text section is less than 256KB, every
two bytes will be occupied by one buckets.
(The minimum size of one buckets is 2 bytes in gprof implementation.)
Change-Id: If9147743cefdc36f40f21e6dc73b9b28f28c9e1e
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1608
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
1. high_pc should be (maximum sample + 1) (Refer to gprof source code)
2. bucket index should be
sample offset
--------------- x (number of bucket)
sample range
For example, if minimum sample is 0 and maximum sample is 5
and the number of bucket is 3.
a = sampled_address - 0
b = 3
c = 6
(a, b, c refer to source code variables)
sampled_address = 0, => a = 0, => bucket_index = 0
sampled_address = 1, => a = 1, => bucket_index = 0
sampled_address = 2, => a = 2, => bucket_index = 1
sampled_address = 3, => a = 3, => bucket_index = 1
sampled_address = 4, => a = 4, => bucket_index = 2
sampled_address = 5, => a = 5, => bucket_index = 2
Change-Id: Ia9fa0e4d9c7183e3e9d7ceaf73e63729f07aa2ce
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1607
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Change variable name 'length' to 'numBuckets'. It is more readable.
Change-Id: I913cba0746f887adf6da401a46cd5e9ea88d2c6d
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1606
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Rewrite the target_*_buffer_default to generate as large accesses as
possible while maintaining natural alignment.
These versions are easy to extend to generate 8-byte accesses to support
64-bit targets, although it requires some conformity from all target
implementations (i.e. they need to refuse unsupported access sizes with
some defined error code, so we can try again with a smaller one).
Change-Id: I00ddcbb1d2fd33f9f8b99cb448cc93505a2421fc
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1221
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The only remaining user is arm7_9 so remove it from the target API and add
it to struct arm7_9_common to support all its variants with minimal
changes. Many of the variants are likely not correct in the cache/mmu
handling when the bulk write is triggered. This patch does nothing to
change that, except for arm946e, where it was easier to do what might be
the right thing.
Change-Id: Ie73ac07507ff0936fefdb90760046cc8810ed182
Signed-off-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-on: http://openocd.zylin.com/1220
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
We already set cpsr in armv7m_build_reg_cache, so lets use it for all other
accesses to this field.
Change-Id: I19b3b21ecf1571bbea12e1be664845e6544f6fa1
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1539
Tested-by: jenkins
Make sure the target support target requests before we enable any receivers.
Change-Id: I8ce42922eaff76fb5e7a114da716f2a6585a6ab5
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1536
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Let the default handler issue an unsupported warning rather than using
empty handler routines that may/may not issue a unsupported warning.
Change-Id: Iafe3e45146981a4cfae39771c3ab7370ac86da48
Signed-off-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-on: http://openocd.zylin.com/1535
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Hsiangkai Wang <hsiangkai@gmail.com>
If target does not support semi-hosting function, it has
no need to provide .get_gdb_fileio_info callback. OpenOCD
will use default function target_get_gdb_fileio_info_default.
The default function just return ERROR_FAIL and gdb_server
will treat every halted condition as normal halted and
return "Txx" to gdb.
Change-Id: I9ddb2be3a1145eae2ef5b712bdea89eb2e0fbc20
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1586
Tested-by: jenkins
Reviewed-by: Nemui Trinomius <nemuisan_kawausogasuki@live.jp>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
After the target was reset we can be sure it's not running any
algorithm.
This fixes the following failure scenario:
On my STM32F103 board after I start the firmware and then stop and try
to "load" in gdb (before doing mon reset halt), I get
Error: timeout waiting for algorithm, a target reset is recommended
However, target reset doesn't help as the flag is still there ("Error:
Target is already running an algorithm"), so I have no choice but to
restart the OpenOCD process.
I'm not sure yet what exactly prevents load from working after my
firmware is initialised, most probably some interrupt is firing and my
handler produces a fault due to garbled RAM.
Change-Id: Idd977f2780a64d84800e3abd412cffc1ab6801b0
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1512
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Enable reading the SWO trace output via STLinkv2 dongles that support
it.
This adds an optional initialization parameter "trace" with which the user
specifies a destination file where SWO trace output is appended as it comes in
as well as the trace module's source clock rate.
STLink will be configured for a 2MHz SWO data rate (STLink's highest
supported rate) if the source clock is > 2MHz, otherwise the source
clock is used as the data rate directly.
For example:
trace swo.log 168000000
If "trace" is specified with a usable file path, the stlink_usb driver will
attempt to configure and read SWO trace data as follows:
- on _run(), the target's TPI and TMI are configured and the STLinkv2 is told
to enable tracing. Only generic ARM TPI and TMI registers are
configured, any MCU-specific settings (ex: pin routing) are the
responsibility of the target firmware. The configuration applied is
based on the STLinkv2's capabilities (UART emulation).
- on _v2_get_status(), the trace data (if any) is fetched from the
STLink after the target status is checked and the target is found to
be running.
- on _halt(), the STLink is told to disable tracing.
When fetching trace data, the entire trace frame is written to the output file
and that data is flushed. An external tool may be used to parse the
trace data into a more human-readable format.
Tested on ARM Cortex M4F and M3 MCUs (STM32F407 and STM32L152).
Change-Id: Ic3983d46c82ba77010c23b0e18ce7b275d917f12
Signed-off-by: Andrey Yurovsky <yurovsky@gmail.com>
Reviewed-on: http://openocd.zylin.com/1524
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Currently, there is no way to notify gdb that program has exited.
Add new target_debug_reason called DBG_REASON_EXIT to notify gdb
the condition has occured. If the debug reason is DBG_REASON_EXIT,
gdb_server will send 'W' packet to tell gdb the process has exited.
Change-Id: I7a371da292716a3e6ac4cc2c31b009a651fe047a
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1242
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
The File I/O remote protocol extension allows the target to use the
host's file system and console I/O to perform various system calls.
To use the function, targets need to prepare two callback functions:
* get_gdb_finish_info: to get file I/O parameters from target
* gdb_fileio_end: pass file I/O response to target
As target is halted, gdb_server will try to get file-I/O information
from target through target_get_gdb_fileio_info(). If the callback function
returns ERROR_OK, gdb_server will initiate a file-I/O request to gdb.
After gdb finishes system call, gdb will pass response of the system call
to target through target_gdb_fileio_end() and continue to run(continue or step).
To implement the function, I add a new data structure in struct target,
called struct gdb_fileio_info, to record file I/O name and parameters.
Details refer to GDB manual "File-I/O Remote Protocol Extension"
Change-Id: I7f4d45e7c9e967b6d898dc79ba01d86bc46315d3
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1102
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
In GDB remote serial protocol, the stop reply packet could contain more
detail stop reason. The currently defined stop reasons are listed below.
* watch
* rwatch
* awatch
* library
* replaylog
This commit adds stop reason, watch/rwatch/awatch, in stop reply packet for
just hit watchpoint. As manual indicates, at most one stop reason should be present.
The function needs target to implement new hook, hit_watchpoint. The hook will fill
the hit watchpoint in second parameter. The information will assist gdb to locate
the watchpoint. If no such information, gdb needs to scan all watchpoints by itself.
Refer to GDB Manual, D.3 Stop Reply Packets
Change-Id: I1f70a1a9cc772e88e641b6171f1a009629a43bd1
Signed-off-by: Hsiangkai Wang <hsiangkai@gmail.com>
Reviewed-on: http://openocd.zylin.com/1092
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Documentation says they should be given values in milliseconds,
DEFAULT_HALT_TIMEOUT matches that too.
Change-Id: Ic1a30fa90f75b412c43fe50ba187d01c3d0a5fba
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1504
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
When I do not have the JTAG adapter connected to the target, I often
end up always reading 1s from the chain. If the OpenOCD is configured
to connect to an ETM-equipped target (i.MX25 ARM9 in my case), this
results in writing garbage values in the etm reg_cache as the ETM bit
fields for the comparators, counters and outputs are wider than the
amount of entries in the corresponding arrays. This later results in a
segfault in the first etm_reg_lookup() call.
Change-Id: Ied81fdbf3a53a3dd749e2e5e97adf86c012df575
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-on: http://openocd.zylin.com/1505
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
EJTAG 1.5, 2.0 and 2.5 have different breakpoint register addresses.
This patch add support of EJTAG 2.0, which is part some broadcom
SoCs.
This work was testet on Broadcom BCM7401.
Change-Id: I4b0ee23871fa9205f9001b7c9165e7b6ebe9ccbf
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1464
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
Split function mips32_configure_break_unit
to mips32_configure_ibs and mips32_configure_dbs
to make code more readable.
This will probably make work easyer with differnet EJTAG versions.
Change-Id: I666f949fd7bc3656bdf75e7bcaadb164f15855dd
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Reviewed-on: http://openocd.zylin.com/1463
Tested-by: jenkins
Reviewed-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
On some CPUs, like bcm7401 with EJTAG v2.0 we can have situation where
CPU do not stops execution. For example, all CP0 commands will have this issue.
In this case we should some hove recover our session. Currently
jump to 0xff20.0200 seems to be good option. If it brake some thing on
newer EJTAG, then check for EJTAG v2.0 should be added.
Change-Id: Icd8841f38a1a85e0f7682b6dc358af8dfaae0744
Signed-off-by: Oleksij Rempel <bug-track@fisher-privat.net>
Reviewed-on: http://openocd.zylin.com/1353
Tested-by: jenkins
Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
