STM32L5 have 512 Kbytes of Flash memory with dual bank architecture.
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
NON-SECURE flash is located at 0x8000000 like L4 devices, so no
big change is needed (secure flash will be subject of another change).
Note: flash driver name is set stm32l5x, in order to extend the commands
with specific L5 commands (to manage TZEN for example ...)
Note: this works only when TZEN=0
Change-Id: Ie758abb4aa19a3f29eeb0702d7dcb43992e4c639
Signed-off-by: Michael Jung <mijung@gmx.net>
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5510
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
This change is a preparation for STM32L5 support on top of L4 driver
STM32L5 flash is quite similar to L4 flash, mainly register names
and offsets and some bits are changed.
flash_regs table is introduced within stm32l4_flash_bank struct in order
to get correct register offsets, by using the driver internal function
'stm32l4_get_flash_reg_by_index'.
To use efficiently register indexes, stm32l4 _[get|read|write]_flash_reg
functions are surcharged to accept register indexes.
IMPORTANT: stm32l4_write_option is not surcharged, and they always accept
the option register offset.
tested on NUCLEO-G474RE and STM32L4R9I-DISCO
Change-Id: I739d3e97d63b831af6aa569c5629db0000209551
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5509
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
PSoC6 erases flash to 0x00 not more common 0xff, so a device
with erased flash loads xPSR.T=0 from the zeroed reset vector.
Wrong thumb bit value caused a target algorithm failed with HardFault.
The low level write to xPSR solved the problem only if xPSR cached
copy was not marked dirty.
Later commit 49bd64347a fixed T setting
for all Cortex-M target algorithms.
Since 49bd64 this part of code is useless as xPSR target_start_algorithm()
sets always xPSR dirty so the effect of the low level write is eliminated
(and proper setting of thumb bit is ensured in target_start_algorithm())
Change-Id: I68aea5e921fbc6203f2fe91a45f10d22869327de
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5875
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Register xPSR is indexed directly with its value 16 or with the
incorrect enum ARMV7M_xPSR.
Replace them with the new enum ARMV7M_REGSEL_xPSR.
Change-Id: I86600e7f78e39002ce45f66d4792d5067c1f541b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5873
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Add space around operators;
use BIT() macro in place of left shifting constant 1;
remove space between cast operator and value;
do not check a pointer before free() it;
add parenthesis around parameters in macros;
fix indentation using only TABs;
remove line continuation '\' at code lines out of macros.
Change-Id: I809e8ee72d7bfe49d0edf10afb36efe2458de77c
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Fixes: e44539d66c ("Flash, FRAM and EEPROM driver for STM32 QUAD-/OCTOSPI interface")
Reviewed-on: http://openocd.zylin.com/5932
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
- write speed up to 150 kByte/s on STM32F469I-disco (due to
SWD clock and USB connection), up to 1 MByte/s on Nucleo-F767ZI
with external STLink-V3 or Nucleo-G474RE with two W25Q256FV in
dual 4-line mode or STM32H73BI-Disco in octal mode
- tested with STM32L476G-disco (64MBit flash, 3-byte addr),
STM32F412G-Disco, STM32F469I-Disco, STM32F746G-Disco, and
STM32L476G-Disco (all 128Mbit flash, 3-byte addr),
STM32F723E-Disco, STM32F769I-Disco (512Mbit flash, 4-byte addr)
STM32L4R9I-Disco, STM32L4P5G-Disco (512MBit octo-flash, DTR, 4-byte addr)
STM32H745I-Disco, STM32H747I-Disco (two 512MBit flash, 4-byte addr)
STM32H73BI-Disco, STM32H735G-Disco (512MBit octo-flash, DTR, 4-byte addr)
- suitable cfg for Discovery boards included
- limited parsing of SFDP data if flash device not hardcoded
(tested only in single/quad mode as most devices either don't
support SFDP at all or have empty(!) SFDP memory)
- 'set' command for auto detection override (e. g. for EEPROMs)
- 'cmd' command for arbitrary SPI commands (reconfiguration, testing etc.)
- makefile for creation of binary loader files
- tcl/board/stm32f469discovery.cfg superseded by stm32f469i-disco.cfg
- tcl/board/stm32f7discovery.cfg removed as name is ambiguous
(superseded by stm32f746g-disco.cfg vs. stm32f769i-disco.cfg)
- dual 4-line mode tested on Nucleo-F767ZI, Nucleo-H743ZI and Nucleo-H7A3ZI-Q
with two W25Q256FV, and on Nucleo-L496ZP-P and Nucleo-L4R5ZI
with two W25Q128FV, sample cfg files included and on STM32H745I-Disco,
STM32H747I-Disco, STM32H750B-Disco
- read/verify/erase_check uses indirect read mode to work around silicon bug in
H7, L4+ and MP1 memory mapped mode (last bytes not readable, accessing last
bytes causes debug interface to hang)
- octospi supported only in single/dual 1-line, 2-line, 4-line
and single 8-line modes, (not in hyper flash mode)
Requirements:
GPIOs must be initialized appropriately, and SPI flash chip be configured
appropriately (1-line ..., QPI, 4-byte addresses ...). This is board/chip
specific, cf. included cfg files. The driver infers most parameters from
current setting in CR, CCR, ... registers.
Change-Id: I54858fbbe8758c3a5fe58812e93f5f39514704f8
Signed-off-by: Andreas Bolsch <hyphen0break@gmail.com>
Reviewed-on: http://openocd.zylin.com/4321
Tested-by: jenkins
Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
While at it, fix some coding style issues.
Change-Id: Id521394d89e0bf787a6f812701c2cc0fe7e4e63f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5919
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Functions and variables that are not used outside the file should
be declared as static.
Change-Id: I52d46ed6d4c9b98a7152eb23274c836416f409a3
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5893
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Warning: line 679, column 4
4th function call argument is an uninitialized value
Change-Id: If62d96e1595be945c8e17885bb402e820fb1ec7b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5903
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Jonathan McDowell <noodles-openocd@earth.li>
HWID is a part of 32 bit CONFIGID register. hwid member of struct nrf5_info
was typed uint32_t to enable direct CONFIGID read and masked afterwards.
Change to uint16_t to unify with hwid in struct nrf5_device_spec
and RM description.
Change-Id: Ib720d3ce23c301aee41d074ea78a6f00a23aed68
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5589
Tested-by: jenkins
nRF52 devices indicate a flash error by emitting hard fault
exception (unlike nRF51 series).
Change error message when NVMC READY read fails. A hard fault
from flash erase/write operation is detected here.
Check exit point of the flash write algo to ensure a failed
write is recognised.
Change-Id: I637eda268a6bf45f7f41bcb9dcd82db8f5cb41b4
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5587
Tested-by: jenkins
nRF51 devices have a clumsy flash protection based on UICR CLENR0.
A code running in RAM can write to a protected flash region without
any hint the protection gets violated.
NVMC flash page erase obeys protection setting but fails absolutely
silently.
Before this change the first problem was not addressed in the code.
To justify the second one, protection was loaded during probe,
after protection setting and after a mass erase.
Move protection updates to the beginning of erase/write operation
and limit them to nRF51 series only. Check for protected sectors
before write.
The change also fixes the problem of 'nrf5 mass_erase' on
nRF52833/840 devices. They use ACL flash protection, which is not
supported in nrf5 driver. mass_erase then looked like it failed.
Change-Id: Ie58cda68eb104d410b02777c3df5b343408e2666
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5522
Tested-by: jenkins
Protection setting has not ever worked. UICR CLENR0 register cannot
be simply written but has to programmed because it resides in UICR
page of the flash.
Enable flash programming before writing CLENR0 and set back to r/o
afterwards.
Inform the user that reset might be required.
Change-Id: Ib0f96c74ba3583ac33f4394ddb57d8c8895adf53
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5586
Tested-by: jenkins
Add support for ATSAMG55x19 Rev.B.
Both chips have nearly the same cidr, however, Rev.B has an incremented version.
Change-Id: I5939c41fa5d54c4d3bfb850964974b878f709d13
Signed-off-by: Benedikt-Alexander Mokroß <mokross@gessler.de>
Reviewed-on: http://openocd.zylin.com/5825
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Tested-by: jenkins
STM32H72x/73x flash is similar to STM32H74x/75x,
except STM32H72x/73x devices have only one single flash bank.
Change-Id: I3d3422dc60234f8273172924f426200210f388cc
Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com>
Reviewed-on: http://openocd.zylin.com/5792
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Modify the format strings to properly handle uint32_t data types.
Change the type of variable retval in 'nor/ambiqmicro.c' to match
both the value to carry and the returned type of the function.
Fix the prototype mismatch of function lpc2900_address2sector()
between the header and the C file.
Change-Id: I68ffba9bd83eec8132f83bff3af993861fd09d84
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5816
Tested-by: jenkins
The function free() can be called with a NULL pointer as argument,
no need to check the argument before. If the pointer is NULL, no
operation is performed by free().
Remove the occurrences of pattern:
if (ptr)
free(ptr);
There are cases where the pointer is set to NULL after free(), but
then re-assigned within few lines. Drop the setting to NULL when
this is evident. Anyway, the compiler will remove the useless
assignment so no reason to be too much aggressive in this change.
Change-Id: I55b2ce7cbe201410016398933e34d33a4b66e30b
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5811
Tested-by: jenkins
Either of protect and protect_check driver callbacks can be NULL. In
virtual_protect, reuse flash_driver_protect which checks for that case
and generates a nice error message and return code. In
virtual_protect_check, there is no corresponding flash_driver_*
function, so add the NULL check directly.
Change-Id: Ia63d85ede640a8382cf5cad0760f5d1ffe4d7cfe
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5782
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: I677bc4487fc2eff2c32e14ca2db5470fddaa63b5
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5778
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
* use proper type codes
* add 0x in front of hex values
* remove some concatenated empty strings
Change-Id: I06a8344d0ed62de7a0f3e2dd8fba69b17eeb3626
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5783
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
this flash is used on the Digilent CMODA7 FPGA board
Change-Id: I6749ca3fbebf2e384051a26a3fd253da5d6e25fb
Signed-off-by: Michael Betz <michibetz@gmail.com>
Reviewed-on: http://openocd.zylin.com/5787
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Fix typos and duplicated words in comments and strings.
Change-Id: I64282c7018462deefeeb8e5f4d0d81942425b3fc
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5758
Tested-by: jenkins
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-by: Christopher Head <chead@zaber.com>
* use proper type codes
* add 0x in front of hex values
* remove some concatenated empty strings
Change-Id: I77e8dd161887f02ecf8019b43d3e8e7cc122ad0e
Signed-off-by: Christopher Head <chead@zaber.com>
Reviewed-on: http://openocd.zylin.com/5780
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Kinetis Flash Configuration Field needs special handling to prevent unwanted
locking of the device. Warn user about any difference between generated
FCF and FCF data in the programmed file. Inform user that re-programming
of already programmed FCF may fail on devices with FTFE flash module.
While on it remove useless setting of is_erased flag after erase.
Change-Id: I3911f436674547fa12ef3886c7d5e8cd889f9e2b
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Fixes: https://sourceforge.net/p/openocd/tickets/270/
Reported-by: Noel Diviney <vk3avm@users.sourceforge.net>
Reviewed-on: http://openocd.zylin.com/5753
Tested-by: jenkins
Since e22c6484ea the trial/error allocation shows
"not enough working area available(requested 2048)" message
on klx.cfg. The message is not clear if it means a problem or not.
Replace with new style allocation using target_get_working_area_avail()
Change-Id: I87fe1e38248fcac29982b72aaba12217a0552f38
Signed-off-by: Tomas Vanek <vanekt@fbl.cz>
Reviewed-on: http://openocd.zylin.com/5752
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
The checkpatch script from Linux kernel v5.1 complains about using
space before comma, before semicolon and between function name and
open parenthesis.
Fix them!
Issue identified using the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types SPACING -f {} \;
The patch only changes amount and position of whitespace, thus
the following commands show empty diff
git diff -w
git log -w -p
git log -w --stat
Change-Id: I1062051d7f97d59922847f5061c6d6811742d30e
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5627
Tested-by: jenkins
It is an error to prefix with "0x" the print of values in decimal.
Replace the incorrect decimal format specifier with PRIx32.
Issue identified by checkpatch script from Linux kernel v5.1 using
the command
find src/ -type f -exec ./tools/scripts/checkpatch.pl \
-q --types PRINTF_0XDECIMAL -f {} \;
Change-Id: I2eb867ef654527b2737ba573a405ec8f97c6a739
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-on: http://openocd.zylin.com/5624
Tested-by: jenkins
Reviewed-by: Andreas Fritiofson <andreas.fritiofson@gmail.com>
Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
Change-Id: Ib9c567e2287f2a99172bd3bd35a81e3205cea421
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/5749
Tested-by: jenkins
Reviewed-by: Christopher Head <chead@zaber.com>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
